Airworthiness Directives:
Federal Register: September 27, 2010 (Volume 75, Number 186)
Proposed Rules
Page 59170-59172
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
DOCID:fr27se10-38
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration 14 CFR Part 39
Docket No. FAA-2010-0942; Directorate Identifier 2010-CE-049-AD
RIN 2120-AA64
Airworthiness Directives; British Aerospace Regional Aircraft
Models Jetstream Series 3101 and Jetstream Model 3201 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
As a result of the fatigue-testing programme on the Jetstream fatigue test specimen, it has been identified that failure of the undercarriage jack mounting shaft assembly can occur.
This condition, if not corrected, could lead to a Main Landing
Gear (MLG) collapse on the ground or during landing and consequently damage to the aeroplane or injury to the occupants.
The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.
DATES: We must receive comments on this proposed AD by November 12, 2010.
ADDRESSES: You may send comments by any of the following methods:
Page 59171
Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (telephone (800) 647-5527) is in the
ADDRESSES section. Comments will be available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Taylor Martin, Aerospace Engineer,
FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City,
Missouri 64106; telephone: (816) 329-4138; fax: (816) 329-4090; e-mail: taylor.martin@faa.gov.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2010-0942;
Directorate Identifier 2010-CE-049-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments.
We will post all comments we receive, without change, to http:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.
Discussion
The European Aviation Safety Agency (EASA), which is the Technical
Agent for the Member States of the European Community, has issued AD
No.: 2010-0162, dated August 4, 2010 (referred to after this as ``the
MCAI''), to correct an unsafe condition for the specified products. The
MCAI states:
As a result of the fatigue-testing programme on the Jetstream fatigue test specimen, it has been identified that failure of the undercarriage jack mounting shaft assembly can occur.
This condition, if not corrected, could lead to a Main Landing
Gear (MLG) collapse on the ground or during landing and consequently damage to the aeroplane or injury to the occupants.
BAE SYSTEMS have now defined safe life limits for these components.
For the reasons described above, this AD requires the application of safe life limits to these components.
You may obtain further information by examining the MCAI in the AD docket.
Relevant Service Information
BAE Systems has issued British Aerospace Jetstream Series 3100 & 3200 Service Bulletin 05-JA090143, dated April 30, 2009; and British
Aerospace Regional Aircraft has issued British Aerospace Jetstream
Series 3100 & 3200 Service Bulletin 32-JA990142, dated March 26,1999.
The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.
FAA's Determination and Requirements of the Proposed AD
This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with this State of Design Authority, they have notified us of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all information and determined the unsafe condition exists and is likely to exist or develop on other products of the same type design.
Differences Between This Proposed AD and the MCAI or Service
Information
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.
Costs of Compliance
We estimate that this proposed AD will affect 80 products of U.S. registry. We also estimate that it would take about 15 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Required parts would cost about $10,000 per product.
Based on these figures, we estimate the cost of the proposed AD on
U.S. operators to be $902,000, or $11,275 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation: 1. Is not a ``significant regulatory action'' under Executive Order 12866; 2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with
Page 59172
this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended] 2. The FAA amends Sec. 39.13 by adding the following new AD:
British Aerospace Regional Aircraft: Docket No. FAA-2010-0942;
Directorate Identifier 2010-CE-049-AD.
Comments Due Date
(a) We must receive comments by November 12, 2010.
Affected ADs
(b) None.
Applicability
(c) This AD applies to British Aerospace Regional Aircraft
Models Jetstream Series 3101 and Jetstream Model 3201 airplanes, all serial numbers, certificated in any category.
Subject
(d) Air Transport Association of America (ATA) Code 32: Landing
Gear.
Reason
(e) The mandatory continuing airworthiness information (MCAI) states:
As a result of the fatigue-testing programme on the Jetstream fatigue test specimen, it has been identified that failure of the undercarriage jack mounting shaft assembly can occur.
This condition, if not corrected, could lead to a Main Landing
Gear (MLG) collapse on the ground or during landing and consequently damage to the aeroplane or injury to the occupants.
BAE SYSTEMS have now defined safe life limits for these components.
For the reasons described above, this AD requires the application of safe life limits to these components.
Actions and Compliance
(f) Unless already done, do the following actions:
(1) Within 30 days after the effective date of this AD, establish the number of landings accumulated since installation of each left and right main landing gear radius rod mounting shaft assemblies following paragraph 2.(A) of BAE Systems British
Aerospace Jetstream Series 3100 & 3200 Service Bulletin 05-JA090143, dated April 30, 2009.
(2) Replace the left and right main landing gear radius rod mounting shaft assembly with an airworthy assembly following British
Aerospace Jetstream Series 3100 & 3200 Service Bulletin 32-JA990142, dated March 26, 1999, within the following:
(i) For Model Jetstream Series 3101: Within 38,220 total landings accumulated on each main landing gear radius rod mounting shaft assembly or within 1,000 landings after the effective date of this AD, whichever occurs later; and
(ii) For Model Jetstream Model 3201: Within 31,038 total landings accumulated on each main landing gear radius rod mounting shaft assembly or within 1,000 landings after the effective date of this AD, whichever occurs later.
(3) After replacing each main landing gear radius rod mounting shaft assembly as required by paragraph (f)(2) of this AD, repetitively thereafter replace each assembly with an airworthy assembly at intervals not to exceed the following life limits:
(i) For Model Jetstream Series 3101: Within 38,220 total landings; and
(ii) For Model Jetstream Model 3201: Within 31,038 total landings.
(4) For operators that do not have landing records, determine the number of landings by multiplying the number of hours time-in- service (TIS) accumulated on each main landing gear radius rod mounting shaft assembly by 0.75. For the purpose of this AD:
(i) 1,000 landings equals 1,333 hours TIS;
(ii) 31,038 landings equals 41,384 hours TIS; and
(ii) 38,220 landings equals 50,960 hours TIS.
(5) Compliance with the life limits set in paragraph (f)(3) of this AD may be done by incorporating these limits into the limitations section of the aircraft maintenance manual. You may do this by inserting a copy of this AD into the limitations section of aircraft maintenance manual.
FAA AD Differences
Note: This AD differs from the MCAI and/or service information as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Standards Office, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. Send information to Attn: Taylor Martin, Aerospace Engineer, FAA, Small
Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4138; fax: (816) 329-4090; e-mail: taylor.martin@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned
OMB Control Number 2120-0056.
Related Information
(h) Refer to MCAI European Aviation Safety Agency (EASA) AD No.: 2010-0162, dated August 4, 2010; BAE Systems British Aerospace
Jetstream Series 3100 & 3200 Service Bulletin 05-JA090143, dated
April 30, 2009; and British Aerospace Regional Aircraft British
Aerospace Jetstream Series 3100 & 3200 Service Bulletin 32-JA990142, dated March 26, 1999, for related information.
Issued in Kansas City, Missouri, on September 21, 2010.
Patrick R. Mullen,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
FR Doc. 2010-24180 Filed 9-24-10; 8:45 am
BILLING CODE 4910-13-P
