Airworthiness Directives:

Federal Register Volume 76, Number 147 (Monday, August 1, 2011)

Proposed Rules

Pages 45713-45715

From the Federal Register Online via the Government Printing Office [www.gpo.gov]

FR Doc No: 2011-19330

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration 14 CFR Part 39

Docket No. FAA-2011-0720; Directorate Identifier 2010-NM-252-AD

RIN 2120-AA64

Airworthiness Directives; Bombardier Inc. Model DHC-8-400 Series

Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

There has been one reported incident where the main landing gear

(MLG) failed to extend during testing of the MLG alternate release system. Investigation revealed that the door release lever bushing was worn, causing an increase in the lateral movement of the release cable system. An increase in free-play within the release cable system would cause additional wear to the door release lever bushing and may lead to the turnbuckle fouling against the nacelle frame.

The bushing wear at the door release lever and turnbuckle fouling could cause a failure in the alternate release system, preventing the landing gear from extending in the case of a failure of the normal MLG extension/retraction system.

* * * * *

The unsafe condition is loss of control during landing. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by September 15, 2011.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue, SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New

Jersey

Page 45714

Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through

Friday, except Federal holidays.

For service information identified in this proposed AD, contact

Bombardier Inc., Q-Series Technical Help Desk, 123 Garratt Boulevard,

Toronto, Ontario M3K 1Y5, Canada; telephone 416-375-4000; fax 416-375- 4539; e-mail thd.qseries@aero.bombardier.com; Internet http://www.bombardier.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind

Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer,

Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft

Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New

York 11590; telephone (516) 228-7303; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2011-0720;

Directorate Identifier 2010-NM-252-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF- 2010-26, dated August 17, 2010 (referred to after this as ``the

MCAI''), to correct an unsafe condition for the specified products. The

MCAI states:

There has been one reported incident where the main landing gear

(MLG) failed to extend during testing of the MLG alternate release system. Investigation revealed that the door release lever bushing was worn, causing an increase in the lateral movement of the release cable system. An increase in free-play within the release cable system would cause additional wear to the door release lever bushing and may lead to the turnbuckle fouling against the nacelle frame.

The bushing wear at the door release lever and turnbuckle fouling could cause a failure in the alternate release system, preventing the landing gear from extending in the case of a failure of the normal MLG extension/retraction system.

This directive is to mandate the incorporation of a new maintenance task to prevent excessive free-play of the turnbuckle and cable within the alternate release system.

The unsafe condition is loss of control during landing. You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Bombardier has issued Temporary Revision (TR) MRB-46, dated

February 4, 2010, to Section 1-32, Systems/Powerplant Maintenance

Program, of the Maintenance Review Board (MRB) Report Part 1, of the

Bombardier Q400 Dash 8 Maintenance Requirements Manual, PSM 1-84-7. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 65 products of U.S. registry. We also estimate that it would take about 1 work-hour per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of the proposed

AD on U.S. operators to be $5,525, or $85 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation

Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in

``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation: 1. Is not a ``significant regulatory action'' under Executive Order 12866;

Page 45715

2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the

Administrator, the FAA proposes to amend 14 CFR Part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended] 2. The FAA amends Sec. 39.13 by adding the following new AD:

Bombardier Inc.: Docket No. FAA-2011-0720; Directorate Identifier 2010-NM-252-AD.

Comments Due Date

(a) We must receive comments by September 15, 2011.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Bombardier Inc. Model DHC-8-400, -401, and -402 airplanes, certificated in any category, having serial numbers 4001 and subsequent.

Subject

(d) Air Transport Association (ATA) of America Code 32: Landing

Gear.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

There has been one reported incident where the main landing gear

(MLG) failed to extend during testing of the MLG alternate release system. Investigation revealed that the door release lever bushing was worn, causing an increase in the lateral movement of the release cable system. An increase in free-play within the release cable system would cause additional wear to the door release lever bushing and may lead to the turnbuckle fouling against the nacelle frame.

The bushing wear at the door release lever and turnbuckle fouling could cause a failure in the alternate release system, preventing the landing gear from extending in the case of a failure of the normal MLG extension/retraction system.

* * * * *

The unsafe condition is loss of control during landing.

Compliance

(f) You are responsible for having the actions required by this

AD performed within the compliance times specified, unless the actions have already been done.

Actions

(g) Within 30 days after the effective date of this AD, revise the maintenance program by incorporating Task 323400-203 specified in Bombardier Temporary Revision (TR) MRB-46, dated February 4, 2010, to Section 1-32, Systems/Powerplant Maintenance Program, of the Maintenance Review Board (MRB) Report Part 1, of the Bombardier

Q400 Dash 8 Maintenance Requirements Manual, PSM 1-84-7. The initial compliance time for the actions specified in Bombardier TR MRB-46, dated February 4, 2010, is within 6,000 flight hours after the effective date of this AD. Thereafter, operate the airplane according to the procedures and compliance times in Bombardier TR

MRB-46, dated February 4, 2010.

No Alternative Actions, Intervals, and/or Critical Design Configuration

Control Limitations (CDCCLs)

(h) After accomplishing the revision required by paragraph (g) of this AD, no alternative actions (e.g., inspections), intervals, and/or CDCCLs may be used unless the actions, intervals, and/or

CDCCLs are approved as an alternative method of compliance (AMOC) in accordance with the procedures specified in paragraph (i) of this

AD.

FAA AD Differences

Note 1: This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(i) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, New

York Aircraft Certification Office (ACO), ANE-170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight

Standards District Office, as appropriate. If sending information directly to the New York ACO, Send it to ATTN: Program Manager,

Continuing Operational Safety, 1600 Stewart Avenue, Suite 410,

Westbury, NY 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this

AD.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

Related Information

(j) Refer to MCAI Canadian Airworthiness Directive CF-2010-26, dated August 17, 2010; and Bombardier Temporary Revision MRB-46, dated February 4, 2010, to Section 1-32, Systems/Powerplant

Maintenance Program, of the Maintenance Review Board Report Part 1, of the Bombardier Q400 Dash 8 Maintenance Requirements Manual, PSM 1-84-7; for related information.

Issued in Renton, Washington, on July 22, 2011.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification

Service.

FR Doc. 2011-19330 Filed 7-29-11; 8:45 am

BILLING CODE 4910-13-P