Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register, Volume 79 Issue 1 (Thursday, January 2, 2014)

Federal Register Volume 79, Number 1 (Thursday, January 2, 2014)

Proposed Rules

Pages 70-72

From the Federal Register Online via the Government Printing Office www.gpo.gov

FR Doc No: 2013-31300

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

Docket No. FAA-2013-1069; Directorate Identifier 2013-NM-197-AD

RIN 2120-AA64

Airworthiness Directives; Bombardier, Inc. Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, Model CL-600-2D15 (Regional Jet Series 705) airplanes, Model CL-600-2D24 (Regional Jet Series 900) airplanes, and Model CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD was prompted by a determination that for certain slat system jam-

disconnect failure cases, the resulting slat skew could lead to failure of the eccentric pin at the slat track attachment. If the pin migrates out of the attachment lugs, this could cause certain slat panels to disconnect from the wing. This proposed AD would require replacing certain locking plates with certain anti-migration assemblies on certain left and right wing slats. We are proposing this AD to prevent failure of the eccentric pins at the slat track attachment, and consequent slat panels disconnecting from the wing, leading to the loss of the airplane.

DATES: We must receive comments on this proposed AD by February 18, 2014.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Bombardier, Inc., 400 Cocircte-Vertu Road West, Dorval, Queacutebec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Cesar Gomez, Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228-7318; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2013-1069; Directorate Identifier 2013-NM-197-AD'' at the beginning of your comments. We specifically invite

Page 71

comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Transport Canada Civil Aviation (TCCA), which is the airworthiness authority for Canada, has issued Canadian Airworthiness Directive CF-

2013-31, dated October 8, 2013 (referred to after this as the Mandatory Continuing Airworthiness Information, or ``the MCAI''), to correct an unsafe condition for the specified products. The MCAI states:

It was discovered that for certain slat system jam-disconnect failure cases, the resulting slat skew could lead to failure of the eccentric pin at the slat track 3-3 attachment. If the pin migrates out of the attachment lugs, this could cause the No. 3 slat panels to disconnect from the wing and could lead to the loss of the aeroplane.

This TCCA AD mandates the replacement of the locking plate with an anti-migration assembly on both the left and right No. 3 slats.

You may examine the MCAI in the AD docket on the Internet at http://www.regulations.gov by searching for and locating it in Docket No. FAA-2013-1069.

Relevant Service Information

Bombardier, Inc. has issued Bombardier Service Bulletin 670BA-27-

066, dated June 10, 2013. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Costs of Compliance

We estimate that this proposed AD affects 401 airplanes of U.S. registry.

We also estimate that it would take about 9 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Required parts would cost about $780 per product. Based on these figures, we estimate the cost of this proposed AD on U.S. operators to be $619,545, or $1,545 per product. According to the manufacturer, some of the costs of this proposed AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all costs in our cost estimate.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in ``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

  1. Is not a ``significant regulatory action'' under Executive Order 12866;

  2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);

  3. Will not affect intrastate aviation in Alaska; and

  4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

    We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

    List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

    The Proposed Amendment

    Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

    PART 39--AIRWORTHINESS DIRECTIVES

    0

  5. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

    Sec. 39.13 Amended

    0

  6. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):

    Bombardier, Inc.: Docket No. FAA-2013-1069; Directorate Identifier 2013-NM-197-AD.

    (a) Comments Due Date

    We must receive comments by February 18, 2014.

    (b) Affected ADs

    None.

    (c) Applicability

    This AD applies to Bombardier, Inc. airplanes, certificated in any category, identified in paragraphs (c)(1), (c)(2), and (c)(3) of this AD.

    (1) Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702) airplanes, serial numbers 10002 through 10335 inclusive.

    (2) Bombardier, Inc. Model CL-600-2D15 (Regional Jet Series 705) airplanes, and Bombardier, Inc. Model CL-600-2D24 (Regional Jet Series 900) airplanes, serial numbers 15001 through 15293 inclusive.

    (3) Bombardier, Inc. Model CL-600-2E25 (Regional Jet Series 1000) airplanes, serial numbers 19002 through 19036 inclusive.

    (d) Subject

    Air Transport Association (ATA) of America Code 27, Flight controls.

    (e) Reason

    This AD was prompted by a determination that for certain slat system jam-disconnect failure cases, the resulting slat skew could lead to failure of the eccentric pin at the slat track attachment. If the pin migrates out of the attachment lugs, this could cause certain slat panels to disconnect from the wing. We are issuing this AD to prevent failure of the eccentric pins at the slat track attachment, and consequent slat panels disconnecting

    Page 72

    from the wing, leading to the loss of the airplane.

    (f) Compliance

    You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

    (g) Replacement

    Within 6,000 flight hours or 30 months, whichever occurs first, after the effective date of this AD: Remove and replace the locking plate having part number (P/N) CC670-12076-1 with an anti-migration assembly having P/N CC670-12370-1, on both the left and right number 3 slats, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 670BA-27-066, dated June 10, 2013.

    (h) Parts Installation Prohibition

    As of the effective date of this AD, no person may install any locking plate having P/N CC670-12076-1 on any airplane.

    (i) Other FAA AD Provisions

    The following provisions also apply to this AD:

    (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office (ACO), ANE-170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone 516-

    228-7300; fax 516-794-5531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. The AMOC approval letter must specifically reference this AD.

    (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they were approved by the State of Design Authority (or its delegated agent, or the DAH with a State of Design Authority's design organization approval). For a repair method to be approved, the repair approval must specifically refer to this AD. You are required to ensure the product is airworthy before it is returned to service.

    (j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) Canadian Airworthiness Directive CF-2013-31, dated October 8, 2013, for related information. This MCAI may be found in the AD docket on the Internet at http://www.regulations.gov by searching for and locating it in Docket No. FAA-2013-1069.

    (2) For service information identified in this AD, contact Bombardier, Inc., 400 Cocircte-Vertu Road West, Dorval, Queacutebec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-

    7401; email thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.

    Issued in Renton, Washington, on December 20, 2013.

    Jeffrey E. Duven,

    Manager, Transport Airplane Directorate, Aircraft Certification Service.

    FR Doc. 2013-31300 Filed 12-31-13; 8:45 am

    BILLING CODE 4910-13-P

VLEX uses login cookies to provide you with a better browsing experience. If you click on 'Accept' or continue browsing this site we consider that you accept our cookie policy. ACCEPT