Airworthiness Directives; Dassault Aviation Airplanes

Federal Register, Volume 83 Issue 106 (Friday, June 1, 2018)

Federal Register Volume 83, Number 106 (Friday, June 1, 2018)

Proposed Rules

Pages 25417-25419

From the Federal Register Online via the Government Publishing Office www.gpo.gov

FR Doc No: 2018-11679

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

Docket No. FAA-2018-0496; Product Identifier 2018-NM-031-AD

RIN 2120-AA64

Airworthiness Directives; Dassault Aviation Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

-----------------------------------------------------------------------

SUMMARY: We propose to adopt a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 2000 and FALCON 2000EX airplanes. This proposed AD was prompted by reports of metallic debris found in the wing slat piccolo tubes; investigation revealed that the debris originated from the flow guide of the ball joint of the wing anti-ice valve. This proposed AD would require repetitive inspections for metallic debris and damage of the flow guide of the ball joint of the wing anti-ice valve, and related investigative and corrective actions if necessary. We are proposing this AD to address the unsafe condition on these products.

DATES: We must receive comments on this proposed AD by July 16, 2018.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this NPRM, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; internet http://www.dassaultfalcon.com. You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

Examining the AD Docket

You may examine the AD docket on the internet at http://

Page 25418

www.regulations.gov by searching for and locating Docket No. FAA-2018-

0496; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th Street, Des Moines, WA 98198; telephone and fax 206-231-3226.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2018-0496; Product Identifier 2018-NM-031-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this NPRM. We will consider all comments received by the closing date and may amend this NPRM based on those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this NPRM.

Discussion

The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued EASA Airworthiness Directive 2018-0022, dated January 29, 2018 (referred to after this as the Mandatory Continuing Airworthiness Information, or ``the MCAI''), to correct an unsafe condition for certain Dassault Aviation Model FALCON 2000 and FALCON 2000EX airplanes. The MCAI states:

Occurrences were reported on Falcon 2000 and Falcon 2000EX aeroplanes, where metallic debris was found in slat piccolo tubes. The technical investigation revealed that debris originated from the flow guide of the ball joint located downstream of the wing anti-ice valve. It was also determined that small debris gathers at the end of the piccolo tube, but larger pieces of debris may stop before, in the distribution piping, restricting the airflow and potentially leading to undetected insufficient wing anti-ice capability.

This condition, if not detected and corrected, could lead to undetected significant ice accretion on the wing, possibly resulting in loss of control of the aeroplane.

To address this potential unsafe condition, Dassault Aviation issued Service Bulletin (SB) F2000EX-413 for Falcon 2000EX and SB F2000-441 for Falcon 2000, providing applicable instructions.

For the reasons described above, this EASA AD requires repetitive detailed inspections for discrepancies including cracks and loss of material of the affected ball joint and, depending on findings, accomplishment of applicable related investigative and corrective actions * * *.

Related investigative actions include, for any loss of material, borescope inspections of anti-ice pipes for debris, nicks, and damage. Corrective actions include replacing any cracked or damaged ball joint, and removing debris from the flow guide. You may examine the MCAI in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-0496.

Related Service Information Under 1 CFR Part 51

Dassault Aviation has issued Service Bulletins F2000-441, dated June 20, 2017; and F2000EX-413, dated July 10, 2017. This service information describes procedures for repetitive inspections for metallic debris and damage of the flow guide of the anti-ice ball joint of the wing. The service information also describes procedures for replacing the ball joint and pipe, and performing borescope inspections of damaged wing anti-ice pipes and removal of any debris from the flow guide. These documents are distinct since they apply to different airplane models. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of these same type designs.

Costs of Compliance

We estimate that this proposed AD affects 348 airplanes of U.S. registry. We estimate the following costs to comply with this proposed AD:

Estimated Costs for Required Actions

----------------------------------------------------------------------------------------------------------------

Cost per Cost on U.S.

Labor cost Parts cost product operators

----------------------------------------------------------------------------------------------------------------

6 work-hours x $85 per hour = $510........................... $0 $510 $177,480

----------------------------------------------------------------------------------------------------------------

We have received no definitive data that would enable us to provide cost estimates for the on-condition actions specified in this proposed AD.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ``General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

This proposed AD is issued in accordance with authority delegated by the Executive Director, Aircraft Certification Service, as authorized by FAA Order 8000.51C. In accordance with that order, issuance of ADs is normally a function of the Compliance

Page 25419

and Airworthiness Division, but during this transition period, the Executive Director has delegated the authority to issue ADs applicable to transport category airplanes to the Director of the System Oversight Division.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

  1. Is not a ``significant regulatory action'' under Executive Order 12866;

  2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);

  3. Will not affect intrastate aviation in Alaska; and

  4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

    List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

    The Proposed Amendment

    Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

    PART 39--AIRWORTHINESS DIRECTIVES

    0

  5. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

    Sec. 39.13 Amended

    0

  6. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):

    Dassault Aviation: Docket No. FAA-2018-0496; Product Identifier 2018-NM-031-AD.

    (a) Comments Due Date

    We must receive comments by July 16, 2018.

    (b) Affected ADs

    None.

    (c) Applicability

    This AD applies to Dassault Aviation Model FALCON 2000 and FALCON 2000EX airplanes, certificated in any category, all serial numbers equipped with any anti-ice pipe having part number (P/N) F2MA724561A1 or P/N F2MA724561A2, except airplanes on which Dassault Modification (mod) M5000 or Dassault mod M5001 has been embodied in production.

    (d) Subject

    Air Transport Association (ATA) of America Code 30, Ice and Rain Protection.

    (e) Reason

    This AD was prompted by reports of metallic debris found in the wing slat piccolo tubes; investigation revealed that the debris originated from the flow guide of the ball joint of the wing anti-

    ice valve. We are issuing this AD to address restricted airflow of the piccolo tubes, leading to insufficient wing anti-ice capability and significant undetected ice accretion on the wing, which could result in loss of control of the airplane.

    (f) Compliance

    Comply with this AD within the compliance times specified, unless already done.

    (g) Repetitive Inspections and Corrective Actions

    Within 25 months after the effective date of this AD: Perform a detailed inspection for discrepancies of the flow guide of the ball joint located downstream of the wing anti-ice valve, and do all applicable related investigative and corrective actions, in accordance with the Accomplishment Instructions of Dassault Aviation Service Bulletin F2000-441, dated June 20, 2017; or Dassault Aviation Service Bulletin F2000EX-413, dated July 10, 2017; as applicable. Repeat the detailed inspection thereafter at intervals not to exceed 25 months. Do all applicable corrective actions before further flight.

    (h) No Reporting Requirement

    Although the service information identified in paragraph (g) of this AD specifies to submit certain information to the manufacturer, this AD does not include that requirement.

    (i) Other FAA AD Provisions

    The following provisions also apply to this AD:

    (1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (j)(2) of this AD. Information may be emailed to: email protected. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

    (2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Dassault Aviation's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature.

    (j) Related Information

    (1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2018-0022, dated January 29, 2018, for related information. This MCAI may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-0496.

    (2) For more information about this AD, contact Tom Rodriguez, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th Street, Des Moines, WA 98198; telephone and fax 206-231-3226.

    (3) For service information identified in this AD, contact Dassault Falcon Jet Corporation, Teterboro Airport, P.O. Box 2000, South Hackensack, NJ 07606; telephone 201-440-6700; internet http://www.dassaultfalcon.com. You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.

    Issued in Des Moines, Washington, on May 22, 2018.

    James Cashdollar,

    Acting Director, System Oversight Division, Aircraft Certification Service.

    FR Doc. 2018-11679 Filed 5-31-18; 8:45 am

    BILLING CODE 4910-13-P

VLEX uses login cookies to provide you with a better browsing experience. If you click on 'Accept' or continue browsing this site we consider that you accept our cookie policy. ACCEPT