Airworthiness directives: de Havilland,
[Federal Register: July 22, 2002 (Volume 67, Number 140)]
[Rules and Regulations]
[Page 47684-47687]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr22jy02-4]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 98-CE-124-AD; Amendment 39-12828; AD 2002-14-28]
RIN 2120-AA64
Airworthiness Directives; de Havilland Inc. Models DHC-2 Mk. I, DHC-2 Mk. II, and DHC-2 Mk. III Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
[[Page 47685]]
SUMMARY: This amendment adopts a new airworthiness directive (AD) that applies to certain de Havilland Inc. (de Havilland) Models DHC-2 Mk. I, DHC-2 Mk. II, and DHC-2 Mk. III airplanes. This AD establishes a life limit for the front fuselage struts and requires you to repetitively replace the front fuselage struts every 15 years or repetitively inspect the struts for corrosion or fatigue damage and replace when the damage exceeds a certain level. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Canada. The actions specified by this AD are intended to prevent structural failure of the front fuselage caused by corrosion or fatigue damage to the struts that develops over time, which could result in reduced or loss of control of the airplane.
EFFECTIVE DATE: This AD becomes effective on September 6, 2002.
ADDRESSES: You may get the service information referenced in this AD from Bombardier Inc., Bombardier Regional Aircraft Division, 123 Garratt Boulevard, Downsview, Ontario, Canada M3K 1Y5; telephone: (416) 633-7310. You may view this information at the Federal Aviation Administration (FAA), Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 98-CE-124-AD, 901 Locust, Room 506, Kansas City, Missouri 64106.
FOR FURTHER INFORMATION CONTACT: Mr. Jon Hjelm, Aerospace Engineer, New York Aircraft Certification Office, 10 Fifth Street, 3rd Floor, Valley Stream, New York 11581-1200; telephone: (516) 256-7523; facsimile: (516) 568-2716.
SUPPLEMENTARY INFORMATION:
Discussion
What Events Have Caused This AD?
Transport Canada, which is the airworthiness authority for Canada, notified FAA that an unsafe condition may exist on certain de Havilland Models DHC-2 Mk. I, DHC-2 Mk. II, and DHC-2 Mk. III airplanes. Transport Canada reports numerous incidents of corrosion of the front fuselage struts. Further analysis of the front fuselage struts reveals that these parts are not life limited and incur corrosion and fatigue damage over time.
What Is The Potential Impact if FAA Took No Action?
Corrosion damage, if not detected and corrected, could result in failure of the front fuselage and possible reduced or loss of control of the airplane.
Has FAA Taken Any Action to This Point?
We issued a proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an AD that would apply to certain de Havilland Models DHC-2 Mk. I, DHC-2 Mk. II, and DHC-2 Mk. III airplanes. This proposal was published in the Federal Register as a notice of proposed rulemaking (NPRM) on March 28, 2002 (67 FR 14886). The NPRM proposed to establish a life limit for the front fuselage struts and would require you to repetitively replace the front fuselage struts every 15 years or repetitively inspect the struts for corrosion or fatigue damage and replace when the damage exceeds a certain level.
Was the Public Invited To Comment?
The FAA encouraged interested persons to participate in the making of this amendment. We did not receive any comments on the proposed rule or on our determination of the cost to the public.
FAA's Determination
What is FAA's Final Determination on This Issue?
After careful review of all available information related to the subject presented above, we have determined that air safety and the public interest require the adoption of the rule as proposed except for minor editorial corrections. We have determined that these minor corrections:
--Provide the intent that was proposed in the NPRM for correcting the unsafe condition; and --Do not add any additional burden upon the public than was already proposed in the NPRM.
Cost Impact
How Many Airplanes Does This AD Impact?
We estimate that this AD affects 354 airplanes in the U.S. registry.
What Is the Cost Impact of This AD on Owners/Operators of the Affected Airplanes?
We estimate the following costs to accomplish the replacement:
Total cost Labor cost
Parts cost
Total cost per airplane
on U.S. Operators
108 workhours x $60 an hour = $6,480 $2,352 per airplane...... $8,832 per airplane per
$3,126,528 per airplane.
replacement.
Compliance Time of This AD
What Will Be the Compliance Time of This AD?
The replacement compliance time of this AD is ``initially replace upon accumulating 15 years from the date of installation of the front fuselage struts or within the next 12 calendar months after the effective date of this AD, whichever occurs later, and thereafter at intervals not to exceed 15 years.'' If the repetitive inspection option is used, then the repetitive compliance time interval will be at 1 and 5 years depending on the method used (provided certain corrosion or damage limits are not exceeded).
Why Is the Compliance Time Presented in Calendar Time Instead of Hours Time-in-Service (TIS)?
The compliance of this AD is presented in calendar time instead of hours TIS. The need for establishing a life limit for the front fuselage struts as specified in this AD is the result of reports of corrosion found in this area on the affected airplanes. Corrosion can occur regardless of whether the aircraft is in operation. In order to ensure that the unsafe condition specified in this AD does not go undetected if the airplane was not in operation for an extended period of time, the compliance is presented in calendar time instead of hours TIS.
Regulatory Flexibility Determination and Analysis
What Are the Requirements of the Regulatory Flexibility Act?
The Regulatory Flexibility Act of 1980 was enacted by Congress to assure that small entities are not unnecessarily or disproportionately burdened by government regulations. This Act establishes ``as principle of regulatory issuance that agencies shall endeavor, consistent with the objectives of the rule and of applicable statutes, to fit regulatory and informational
[[Page 47686]]
requirements to the scale of the businesses, organizations, and governmental jurisdictions subject to regulation.'' To achieve this principle, the Act requires agencies to solicit and consider flexible regulatory proposals and to explain the rationale for their actions. The Act covers a wide range of small entities, including small businesses, not-for-profit organizations, and small governmental jurisdictions.
Agencies must perform a review to determine whether a proposed or final rule will have a significant economic impact on a substantial number of small entities. If the determination is that the rule will, the Agency must prepare a regulatory flexibility analysis as described in the RFA.
However, if an agency determines that a proposed or final rule is not expected to have a significant economic impact on a substantial number of small entities, section 605(b) of the RFA provides that the head of the agency may so certify and a regulatory flexibility analysis is not required. The certification must include a statement providing the factual basis for this determination, and the reasoning should be clear.
What Is FAA's Determination?
The FAA has determined that this AD could have a significant economic impact on a substantial number of small entities. However, we have determined that we should continue with this action in order to address the unsafe condition and ensure aviation safety.
You may obtain a copy of the complete Regulatory Flexibility Analysis (entitled ``Final Regulatory Flexibility Analysis'') that was prepared for this AD from the Docket file at the location listed under the ADDRESSES section of this document.
Regulatory Impact
Does This AD Impact Various Entities?
The regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132.
Does This AD Involve a Significant Rule or Regulatory Action?
For the reasons discussed above, I certify that this action (1) is not a ``significant regulatory action'' under Executive Order 12866; (2) is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) could have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the final evaluation prepared for this action is contained in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
-
The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
-
FAA amends Sec. 39.13 by adding a new AD to read as follows:
2002-14-28 de Havilland Inc.: Amendment 39-12828; Docket No. 98-CE- 124-AD.
(a) What airplanes are affected by this AD? This AD affects all serial numbers of Models DHC-2 Mk. I, DHC-2 Mk. II, and DHC-2 Mk. III airplanes that are certificated in any category.
(b) Who must comply with this AD? Anyone who wishes to operate any of the airplanes identified in paragraph (a) of this AD must comply with this AD.
(c) What problem does this AD address? The actions specified by this AD are intended to prevent structural failure of the front fuselage caused by corrosion or fatigue damage to the struts that develops over time, which could result in reduced or loss of control of the airplane.
(d) What actions must I accomplish to address this problem? To address this problem, you must accomplish the following:
Actions
Compliance
Procedures
(1) Replace each front
Initially replace In accordance with fuselage strut with a new upon accumulating the applicable strut. Part numbers for 15 years on each maintenance manual, existing and replacement front fuselage
as specified in de front fuselage struts parts strut or within the Havilland Parts are presented in paragraph next 12 calendar Service Manual 1-2- (e) of this AD.
months after
2, Part 5, September 6, 2002 Temporary Revision (the effective date 2-22; and de of this AD),
Havilland Parts whichever occurs Service Manual 1-2T- later. Repetitively 2, Part 5, replace thereafter Temporary Revision upon accumulating 2T-6, both dated 15 years on each August 3, 1998. front fuselage strut.
[[Page 47687]]
(2) As an alternative method Initially inspect For the detailed of compliance to the
upon accumulating inspection, use an replacements in paragraph 15 years on each inspection light, (d)(1) of this AD, you may front fuselage
inspection mirror, repetitively inspect each strut or within the and 10X magnifying front fuselage strut, as next 12 calendar glass. For the follows:.
months after
ultrasonic (i) perform a detailed
September 6, 2002 inspection, use FAA- inspection of each front (the effective date approved procedures fuselage strut and all
of this AD),
that follow a fittings attached to the whichever occurs similar calibration frame for damage
later. Accomplish and measures strut (corrosion, cracks, dents). the repetitive
thickness to that When fatigue damage is
detailed inspection detailed in found, you must replace the thereafter at
Bombardier Service damaged strut. After each intervals not to Bulletin 2/49, inspection, clean the drain exceed 12 months Revision C. holes around the bottom end and the ultrasonic fitting and protect the thickness tube with an appropriate measurement at corrosion preventive spray. intervals not to Part numbers for existing exceed 5 years. and replacement front
Accomplish the fuselage struts parts are corrosion presented in paragraph (e) prevention work of this AD.
prior to further (ii) perform an ultrasonic flight after each thickness measurement of inspection. all surface on each front Accomplish the fuselage strut. When
replacement prior minimum thickness is below to further flight 0.030 inches, you must
after damage is replace the affected strut. found or the Part numbers for existing thickness is found and replacement front
below 0.030 inches. fuselage struts parts are Then, after presented in paragraph (e) replacement either of this AD.
replace with a new strut at 15-year intervals thereafter or repetitively inspect as prescribed above beginning at 15 years after each replacement.
(3) Do not install, on any As of September 6, Not Applicable. affected airplane, any
2002 (the effective front fuselage strut unless date of this AD. it has a part number specified in the Replacement Part Number column of the chart presented in paragraph (e) of this AD.
(e) What part number front fuselage struts should I use for replacements? The following charts presents the part numbers for existing parts and replacement parts for the front fuselage strut replacements:
Installed part No.
Replacement part No.
Description
C2FS209 or C2FS3281A............. C2FS3281A
Strut Assembly Front Fuselage, Left. C2FS210 or C2FS3282A............. C2FS3282A
Strut Assembly Front Fuselage, Right.
(f) Can I comply with this AD in any other way? You may use an alternative method of compliance or adjust the compliance time if:
(1) Your alternative method of compliance provides an equivalent level of safety; and
(2) The Manager, New York Aircraft Certification Office (ACO), approves your alternative. Submit your request through an FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, New York ACO.
Note 1: This AD applies to each airplane identified in paragraph (a) of this AD, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/ operator must request approval for an alternative method of compliance in accordance with paragraph (f) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if you have not eliminated the unsafe condition, specific actions you propose to address it.
(g) Where can I get information about any already-approved alternative methods of compliance? Contact Jon Hjelm, Aerospace Engineer, FAA, New York Aircraft Certification Office, 10 Fifth Street, Third Floor, Valley Stream, New York 11581; telephone: (516) 256-7523; facsimile: (516) 256-2716.
(h) What if I need to fly the airplane to another location to comply with this AD? The FAA can issue a special flight permit under sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate your airplane to a location where you can accomplish the requirements of this AD.
(i) How do I get copies of the documents referenced in this AD? You may direct technical questions to or get copies of the documents referenced in this AD from Bombardier Inc., Bombardier Regional Aircraft Division, 123 Garratt Boulevard, Downsview, Ontario, Canada M3K 1Y5; telephone: (416) 633-7310. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.
Note 2: The subject of this AD is addressed in Canadian AD CF- 98-37R1, dated August 20, 1999.
(j) When does this amendment become effective? This amendment becomes effective on September 6, 2002.
Issued in Kansas City, Missouri, on July 15, 2002. Dorenda D. Baker, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 02-18334Filed7-19-02; 8:45 am]
BILLING CODE 4910-13-P
