Airworthiness directives: Stemme GmbH & Co.,

[Federal Register: April 16, 2004 (Volume 69, Number 74)]

[Proposed Rules]

[Page 20566-20568]

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

[DOCID:fr16ap04-21]

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

[Docket No. 2003-CE-58-AD]

RIN 2120-AA64

Airworthiness Directives; Stemme GmbH & Co. Models S10, S10-V, and S10-VT Sailplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for all Stemme GmbH & Co. Models S10, S10-V, and S10-VT sailplanes. This proposed AD would require you to remove the drive shaft assembly and ship it to the service department of Stemme GmbH & Co. The engine is mounted behind the two side-by-side seats. The engine combined with the carbon fiber drive shaft turn the centrifugally extended propeller. After an initial visual inspection, the service department will perform an operational check to determine whether the drive shaft can be further used or must be replaced. Once corrective action is identified, a drive shaft will be shipped to you for installation. This proposed AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. We are issuing this proposed AD to detect and correct incorrectly glued drive shafts, which could result in drive shaft failure. During self-takeoff or critical periods of landing, failure of the drive shaft could lead to loss of control of the sailplane.

DATES: We must receive any comments on this proposed AD by May 26, 2004.

ADDRESSES: Use one of the following to submit comments on this proposed AD:

By mail: FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-58-AD, 901 Locust, Room 506, Kansas City, Missouri 64106.

By fax: (816) 329-3771.

By e-mail: 9-ACE-7-Docket@faa.gov. Comments sent electronically must contain ``Docket No. 2003-CE-58-AD'' in the subject line. If you send comments electronically as attached electronic files, the files must be formatted in Microsoft Word 97 for Windows or ASCII.

You may get the service information identified in this proposed AD from Stemme GmbH & Co. AG, Flugplatzstra[beta]e F 2, Nr. 7, D-15344 Strausberg, Germany.

You may view the AD docket at FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-58-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Office hours are 8 a.m. to 4 p.m., Monday through Friday, except Federal holidays.

FOR FURTHER INFORMATION CONTACT: Gregory Davison, Aerospace Engineer, Small Airplane Directorate, ACE-112, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4130; facsimile: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Comments Invited

How do I comment on this proposed AD? We invite you to submit any written relevant data, views, or arguments regarding this proposal. Send your comments to an address listed under ADDRESSES. Include ``AD Docket No. 2003-CE-58-AD'' in the subject line of your comments. If you want us to acknowledge receipt of your mailed comments, send us a self- addressed, stamped postcard with the docket number written on it. We will date-stamp your postcard and mail it back to you.

Are there any specific portions of this proposed AD I should pay attention to? We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. If you contact us through a nonwritten communication and that contact relates to a substantive part of this proposed AD, we will summarize the contact and place the summary in the docket. We will consider all comments received by the closing date and may amend this proposed AD in light of those comments and contacts.

Discussion

What events have caused this proposed AD? The Luftfahrt-Bundesamt (LBA), which is the airworthiness authority for Germany, recently notified FAA that an unsafe condition may exist on all Stemme GmbH & Co. Models S10, S10-V, and S10-VT sailplanes. The LBA reports that two drive shafts have failed during normal operation of the sailplane. The flanges of the drive shafts started to rotate within the carbon fibre reinforced plastics-tube (CFRP-tube), while the drive shafts still appeared to be intact when looking at them from the outside. The metal flanges on both ends of the drive shafts might not have been properly glued to the CFRP-tube.

What are the consequences if the condition is not corrected? Incorrectly glued drive shafts could result in drive shaft failure. This failure could lead to loss of control of the sailplane.

Is there service information that applies to this subject? Stemme GmbH & Co. has issued Service Bulletin No. A31-10-058, dated November 8, 2001.

What are the provisions of this service information? The service bulletin includes procedures for the inspection of the drive shaft.

What action did the LBA take? The LBA classified this service bulletin as mandatory and issued German AD Number 2002-113, dated May 2, 2002, to ensure the continued airworthiness of these sailplanes in Germany.

[[Page 20567]]

Did the LBA inform the United States under the bilateral airworthiness agreement? These Stemme GmbH & Co. Models S10, S10-V, and S10-VT sailplanes are manufactured in Germany and are type-certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement.

Under this bilateral airworthiness agreement, the LBA has kept us informed of the situation described above.

FAA's Determination and Requirements of This Proposed AD

What has FAA decided? We have examined the LBA's findings, reviewed all available information, and determined that AD action is necessary for products of this type design that are certificated for operation in the United States.

Since the unsafe condition described previously is likely to exist or develop on other Stemme GmbH & Co. Models S10, S10-V, and S10-VT sailplanes of the same type design that are registered in the United States, we are proposing AD action to detect and correct incorrectly glued drive shafts that could result in drive shaft failure. This failure could lead to loss of control of the sailplane.

What would this proposed AD require? This proposed AD would require you to incorporate the actions in the previously-referenced service bulletin.

How does the revision to 14 CFR part 39 affect this proposed AD? On July 10, 2002, we published a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs FAA's AD system. This regulation now includes material that relates to altered products, special flight permits, and alternative methods of compliance. This material previously was included in each individual AD. Since this material is included in 14 CFR part 39, we will not include it in future AD actions.

Costs of Compliance

How many sailplanes would this proposed AD impact? We estimate that this proposed AD affects 57 sailplanes in the U.S. registry.

What would be the cost impact of this proposed AD on owners/ operators of the affected sailplanes? We estimate the following costs to remove the drive shaft, ship it to and from manufacturer's service department, and install the drive shaft after manufacturer's inspection is complete:

Shipping cost Total cost Total cost Labor cost

Parts cost to and from per

on U.S. manufacturer sailplane operators

6 workhours est. $65 per hour = $390.....................

N/A

$1,080 $1,470 $83,790

We estimate the following costs for the manufacturer to do the proposed inspection and any necessary repairs that would be required based on the results of this proposed inspection. We have no way of determining the number of sailplanes that may need this repair:

Total cost Labor cost

Parts cost per sailplane

Inspection and testing by manufacturer--$210..

N/A

$210

Replacement of drive shaft--labor is included

$5,780

$5780 in the parts cost............................

Regulatory Findings

Would this proposed AD impact various entities? We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

Would this proposed AD involve a significant rule or regulatory action? For the reasons discussed above, I certify that this proposed AD:

  1. Is not a ``significant regulatory action'' under Executive Order 12866;

  2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

  3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

    We prepared a summary of the costs to comply with this proposed AD and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include ``AD Docket No. 2003-CE-58-AD'' in your request.

    List of Subjects in 14 CFR Part 39

    Air transportation, Aircraft, Aviation safety, Safety.

    The Proposed Amendment

    Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend 14 CFR part 39 as follows:

    PART 39--AIRWORTHINESS DIRECTIVES

  4. The authority citation for part 39 continues to read as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701.

    Sec. 39.13 [Amended]

  5. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):

    Stemme GmbH & Co.: Docket No. 2003-CE-58-AD

    When Is the Last Date I Can Submit Comments on This Proposed AD?

    (a) We must receive comments on this proposed airworthiness directive (AD) by May 26, 2004.

    What Other ADs Are Affected by This Action?

    (b) None.

    What Sailplanes Are Affected by This AD?

    (c) This AD affects the following sailplane models and serial numbers that are certificated in any category:

    [[Page 20568]]

    Models

    Serial numbers

    (1) S10-VT....................... 11-001 through 11-055, 11-057, 11- 058, and 11-060 through 11-066;

    (2) S10-V........................ 14-003, 14-004, 14-007, 14-014, 14- 015, and 14-018 through 14-030, as well as conversion serial numbers 14- 028M, 14-036M, and 14-038M; and

    (3) S10.......................... 10-08 and 10-13.

    What Is the Unsafe Condition Presented in This AD?

    (d) The actions specified in this AD are intended to identify incorrectly glued drive shafts, which could result in drive shaft failure. This failure could lead to loss of control of the sailplane.

    What Must I Do To Address This Problem?

    (e) To address this problem, you must do the following:

    Action

    Compliance

    Procedures

    (1) Remove the drive shaft and ship it to Do within 50 hours time in

    Follow the procedures in the the service department of Stemme GmbH & service from the effective date Stemme GmbH & Co. Service Co. for inspection at the following

    of this AD.

    Bulletin A31-10-058, dated address: Stemme GmbH & Co. AG,

    November 8, 2001. Flugplatzstra[beta]e F 2, Nr. 7, D-15344 Strausberg, Germany. The sailplane's Component History Card and information about the current operating times (time since new, time since overhaul) must be included. (2) Install the drive shaft after Stemme Prior to further flight after Follow the procedures in the GmbH & Co. has performed the inspections, receiving the returned drive Stemme GmbH & Co. Service determined corrective action, and returned shaft.

    Bulletin A31-10-058, dated the drive shaft.

    November 8, 2001.

    May I Request an Alternative Method of Compliance?

    (f) You may request a different method of compliance or a different compliance time for this AD by following the procedures in 14 CFR 39.13. The principal inspector may add comments and will send your request to the Manager, Flight Standards, FAA. For information on any already approved alternative methods of compliance, contact Gregory M. Davison, Aerospace Engineer, Small Airplane Directorate, ACE-112, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4130; facsimile: (816) 329-4090.

    May I Get Copies of the Documents Referenced in this AD?

    (g) You may get copies of the documents referenced in this AD from Stemme GmbH & Co., Flugplatzstra[beta]e F 2, Nr. 7, D-15344 Strausberg, Germany. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

    Is There Other Information That Relates to This Subject?

    (h) LBA Airworthiness Directive No. 2002-113, dated May 2, 2002, and Stemme GmbH & Co. Service Bulletin A31-10-058, dated November 8, 2001, also address the subject of this AD.

    Issued in Kansas City, Missouri, on April 8, 2004. William J. Timberlake, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.

    [FR Doc. 04-8586 Filed 4-15-04; 8:45 am]

    BILLING CODE 4910-13-P

VLEX uses login cookies to provide you with a better browsing experience. If you click on 'Accept' or continue browsing this site we consider that you accept our cookie policy. ACCEPT