Airworthiness Directives; The Boeing Company Airplanes

Federal Register, Volume 81 Issue 39 (Monday, February 29, 2016)

Federal Register Volume 81, Number 39 (Monday, February 29, 2016)

Rules and Regulations

Pages 10074-10077

From the Federal Register Online via the Government Publishing Office www.gpo.gov

FR Doc No: 2016-04138

-----------------------------------------------------------------------

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 39

Docket No. FAA-2016-3981; Directorate Identifier 2015-NM-053-AD; Amendment 39-18417; AD 2016-04-23

RIN 2120-AA64

Airworthiness Directives; The Boeing Company Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

-----------------------------------------------------------------------

SUMMARY: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8 airplanes. This AD requires an inspection of the station 337 (door number 1) outboard partitions for a tie rod and quick release pins, and to ensure that both partition supports are engaged in the structural bracket at each outboard partition, and corrective actions if necessary. This AD was prompted by reports of missing right and left outboard partition tie rods at door number 1. We are issuing this AD to detect and correct partitions with missing tie rods or release pins or with supports that are not engaged in the structural bracket. These partitions could come loose during a high-acceleration event and strike the flight attendant seats in the door 1 location, causing serious injury to the seat occupants, or could affect safe egress from the airplane.

Page 10075

DATES: This AD is effective March 15, 2016.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of March 15, 2016.

We must receive comments on this AD by April 14, 2016.

ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

Fax: 202-493-2251.

Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this final rule, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-

5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com. You may view this referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221. It is also available on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA 2016-

3981.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2016-

3981; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Francis Smith, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW., Renton, WA 98057-

3356; phone 425-917-6596; fax 425-917-6590; email: francis.smith@faa.gov.

SUPPLEMENTARY INFORMATION:

Discussion

We have received reports of missing right and left outboard partition tie rods at station 337 (door number 1) on Model 787-8 airplanes as a result of a manufacturing escape (i.e., insufficient documentation to show engineering details). We are issuing this AD to detect and correct partitions with missing tie rods or release pins or with supports that are not engaged in the structural bracket. These partitions could come loose during a high-acceleration event and strike the flight attendant seats in the door 1 location, causing serious injury to the seat occupants, or could affect safe egress from the airplane.

Related Service Information Under 1 CFR Part 51

We reviewed Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014. The service bulletin describes procedures for an inspection of the station 337 outboard partitions for a tie rod and quick release pins, and also to determine that both partition supports are engaged in the structural bracket, and corrective actions. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section.

FAA's Determination

We are issuing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design.

AD Requirements

This AD requires accomplishing the actions specified in the service information described previously, except as discussed under ``Differences Between the AD and the Service Information.''

The phrase ``corrective actions'' is used in this AD. ``Corrective actions'' are actions that correct or address any condition found. Corrective actions in an AD could include, for example, repairs.

Differences Between the AD and the Service Information

Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014, specifies to do the general visual inspection ``in accordance with the Tasks in Table 6'' of the service information. However ``Table 6'' does not exist. The tasks are identified in Table 4 of the service information. Therefore, this AD requires that the inspection be done in accordance with the tasks in Table 4 of the Accomplishment Instructions of Boeing Service Bulletin B787-81205-

SB250081-00, Issue 001, dated December 9, 2014.

FAA's Justification and Determination of the Effective Date

Since there are currently no domestic operators of this product, we find that notice and opportunity for prior public comment are unnecessary and that good cause exists for making this amendment effective in less than 30 days.

Comments Invited

This AD is a final rule that involves requirements affecting flight safety and was not preceded by notice and an opportunity for public comment. However, we invite you to send any written data, views, or arguments about this AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket Number FAA-2016-3981; Directorate Identifier 2015-NM-053-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this AD. We will consider all comments received by the closing date and may amend this AD because of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this AD.

Costs of Compliance

We estimate that this AD affects 0 airplanes of U.S. registry.

We estimate the following costs to comply with this AD:

Page 10076

Estimated Costs

----------------------------------------------------------------------------------------------------------------

Cost per Cost on U.S.

Action Labor cost Parts cost product operators

----------------------------------------------------------------------------------------------------------------

Inspection........................ 3 work-hours x $85 per $0 $255 $0

hour = $255.

----------------------------------------------------------------------------------------------------------------

We estimate the following costs to do any necessary repairs that would be required based on the results of the inspection. We have no way of determining the number of aircraft that might need these repairs:

On-Condition Costs

----------------------------------------------------------------------------------------------------------------

Cost per

Action Labor cost Parts cost product

----------------------------------------------------------------------------------------------------------------

Corrective action......................... 1 work-hour x $85 per hour = $85.. $1,027 $1,112

----------------------------------------------------------------------------------------------------------------

According to the manufacturer, some of the costs of this AD may be covered under warranty, thereby reducing the cost impact on affected individuals. We do not control warranty coverage for affected individuals. As a result, we have included all costs in our cost estimate.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation Programs'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: ``General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a ``significant regulatory action'' under Executive Order 12866,

(2) Is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),

(3) Will not affect intrastate aviation in Alaska, and

(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

0

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 Amended

0

2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):

2016-04-23 The Boeing Company: Amendment 39-18417; Docket No. FAA-

2016-3981; Directorate Identifier 2015-NM-053-AD.

(a) Effective Date

This AD is effective March 15, 2016.

(b) Affected ADs

None.

(c) Applicability

This AD applies to The Boeing Company Model 787-8 airplanes, certificated in any category, as identified in Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014.

(d) Subject

Air Transport Association (ATA) of America Code 25, Equipment/

furnishings.

(e) Unsafe Condition

This AD was prompted by reports of missing right and left outboard partition tie rods at station 337 (door number 1). We are issuing this AD to detect and correct partitions with missing tie rods or release pins or with supports that are not engaged in the structural bracket. These partitions could come loose during a high-

acceleration event and strike the flight attendant seats in the door 1 location, causing serious injury to the seat occupants, or could affect safe egress from the airplane.

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Inspection and Corrective Actions

Within 60 months after the effective date of this AD: Do a general visual inspection of the applicable station 337 outboard partitions for a tie rod and quick release pins, and to ensure that both partition supports are engaged in the structural bracket at each outboard partition; and do all applicable corrective actions; in accordance with the Accomplishment Instructions of Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014; except where Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014, specifies to do the general visual inspection ``in accordance with the Tasks in Table 6,'' this AD requires that the inspection be done in accordance with the tasks in Table 4 of the Accomplishment Instructions of Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014. Do all applicable corrective actions before further flight.

(h) Alternative Methods of Compliance (AMOCs)

(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as

Page 10077

appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (i) of this AD. Information may be emailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov.

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

(3) An AMOC that provides an acceptable level of safety may be used for any repair, modification, or alteration required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Seattle ACO, to make those findings. To be approved, the repair method, modification deviation, or alteration deviation must meet the certification basis of the airplane, and the approval must specifically refer to this AD.

(i) Related Information

For more information about this AD, contact Francis Smith, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle ACO, 1601 Lind Avenue SW., Renton, WA 98057-

3356; phone 425-917-6596; fax 425-917-6590; email: francis.smith@faa.gov.

(j) Material Incorporated by Reference

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise.

(i) Boeing Service Bulletin B787-81205-SB250081-00, Issue 001, dated December 9, 2014.

(ii) Reserved.

(3) For Boeing service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; telephone 206-544-5000, extension 1; fax 206-766-5680; Internet https://www.myboeingfleet.com.

(4) You may view this service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, WA. For information on the availability of this material at the FAA, call 425-227-1221.

(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.

Issued in Renton, Washington, on February 18, 2016.

Dionne Palermo,

Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.

FR Doc. 2016-04138 Filed 2-26-16; 8:45 am

BILLING CODE 4910-13-P

VLEX uses login cookies to provide you with a better browsing experience. If you click on 'Accept' or continue browsing this site we consider that you accept our cookie policy. ACCEPT