Airworthiness standards: Special conditions— Boeing Model 747-400 airplane,

[Federal Register: January 10, 2006 (Volume 71, Number 6)]

[Rules and Regulations]

[Page 1485-1488]

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

[DOCID:fr10ja06-3]

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration

14 CFR Part 25

[Docket No. NM323; Special Conditions No. 25-311-SC]

Special Conditions: Boeing Model 747-400 Airplane; Large Non- Structural Glass in the Passenger Compartment

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final special conditions.

SUMMARY: These special conditions are issued for a Boeing Model 747-400 airplane modified by Lufthansa Technik AG. This airplane will have a novel or unusual design feature associated with the installation of large non-structural glass items in the cabin area of an executive interior occupied by passengers and crew. The installation of these items in a passenger compartment, which can be occupied during taxi, takeoff, and landing, is a novel or unusual design feature with respect to the material used. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.

Effective Date: January 3, 2006.

FOR FURTHER INFORMATION CONTACT: Alan Sinclair, Airframe/Cabin Safety Branch, ANM-115, Transport Airplane Directorate, Aircraft Certification Service, 1601 Lind Avenue SW., Renton, Washington, 98055-4056; telephone (425) 227-2195; facsimile (425) 227-1232, e-mail address alan.sinclair@faa.gov.

SUPPLEMENTARY INFORMATION:

Background

On September 8, 2003, Lufthansa Technik AG, Weg beim J[auml]ger 193, D-22335, Hamburg, Germany, applied for a supplemental type certificate (STC) for large non-structural glass items in the cabin area of the executive interior occupied by passengers and crew in a Boeing Model 747-400 airplane. The Boeing Model 747-400 airplane is approved under Type Certificate No. A20WE, and is a large transport category airplane with upper and main passenger decks. The airplane is limited to 660 passengers or less, depending on the interior configuration. This specific Model 747-400 configuration includes seating provisions for 105 passengers.

Type Certification Basis

Under the provisions of Sec. 21.101, Lufthansa Technik must show that the Boeing Model 747-400 airplane, as changed, continues to meet the applicable provisions of the regulations incorporated by reference in Type Certificate No. A20WE or the applicable regulations in effect on the date of application for the change. The regulations incorporated by reference in the type certificate are commonly referred to as the ``original type certification basis.'' The regulations incorporated by reference in Type Certificate No. A20WE are as follows: Amendments 25-1 through 25-59 with exceptions for the Boeing Model 747-400. In addition, the certification basis includes certain special conditions, exemptions, or later amended sections of the applicable part that are not relevant to these special conditions. The U.S. type certification basis for the Model 747-400 is established in accordance with Sec. Sec. 21.17 and 21.29 and the type certification application date.

If the Administrator finds that the applicable airworthiness regulations

[[Page 1486]]

(i.e., 14 CFR part 25, as amended) do not contain adequate or appropriate safety standards for the Boeing Model 747-400 airplane because of a novel or unusual design feature, special conditions are prescribed under the provisions of Sec. 21.16.

In addition to the applicable airworthiness regulations and special conditions, the Boeing Model 747-400 airplane must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34 and the noise certification requirements of 14 CFR part 36.

Special conditions, as defined in Sec. 11.19, are issued in accordance with Sec. 11.38 and become part of the type certification basis in accordance with Sec. 21.101.

Special conditions are initially applicable to the model for which they are issued. Should Lufthansa Technik apply for a supplemental type certificate to modify any other model included on the same type certificate to incorporate the same or similar novel or unusual design feature, the special conditions would also apply to the other model under the provisions of Sec. 21.101.

Novel or Unusual Design Features

The Boeing Model 747-400 will incorporate the following novel or unusual design feature, the installation of large non-structural glass items, typically in the form of glass sheets in the cabin area of an executive interior occupied by passengers and crew.

These installations would be for aesthetic purposes, not for safety, in components other than windshields or windows. For these special conditions, a large glass item is 4 kg (approximately 10 pounds) and greater in mass. This limit was established as the mass at which a glass component could be expected to potentially cause widespread injury if it were to shatter or break free from its retention system.

These special conditions address the novel and unusual design features for the use of large non-structural glass in the passenger cabin. These large glass items would be installed in occupied rooms or areas during taxi, take off, and landing, or rooms or areas that occupants do have to enter or pass through to get to any emergency exit. The installations of large non-structural glass items may include, but are not limited to, the following items:

Glass partitions.

Glass attached to the ceiling.

Wall/door mounted mirrors/glass panels.

Discussion

The existing part 25 regulations only address the use of glass in windshields, instrument or display transparencies, or window applications. The regulations treat glass as unique for special applications where no other material will serve and address the adverse properties of glass.

Section 25.775, ``Window and windshields,'' provides for the use of glass in airplanes, but limits glass to windshields and instrument or display transparencies. Furthermore, except for bolted-in windshields, there is limited experience with either adhesive or mechanical retention methods for large glass objects installed in an airplane subject to high loads supported by flexible restraints.

The regulations provide for the following use of glass in the passenger cabin:

  1. Glass items installed in rooms or areas in the cabin that are not occupied during taxi, take off, and landing, and occupants do not have to enter or pass through the room or area to get to any emergency exit.

  2. Glass items integrated into a functional device whose operation is dependent upon the characteristics of glass, such as instrument or indicator protective transparencies, or monitor screens such as liquid crystal display (LCD) or plasma displays. These glass items may be installed in any area in the cabin regardless of occupancy during taxi, take-off, and landing. Acceptable means for these items may depend on the size and specific location of the device.

  3. Small glass items installed in occupied rooms or areas during taxi, take off, and landing, or rooms or areas that occupants do have to enter or pass through to get to any emergency exit. For the purposes of these special conditions, a small glass item is less than 4 kg in mass, or a group of glass items weighing less than 4 kg in mass.

    The glass items in numbers one, two, and three (above) have been restricted to applications where the potential for injury is either highly localized (such as instrument faces) or the location is such that injury due to failure of the glass is unlikely (e.g., mirrors in lavatories). These glass items are subject to the inertia loads contained in Sec. 25.561 and maximum positive differential pressure for items like monitors, but are not subject to these special conditions. They have been found acceptable through project specific means of compliance requiring testing to meet the requirement Sec. 25.785(d), and by adding a protective polycarbonate layer that covers the glass exposed to the cabin.

    The use of glass in airplanes utilizes the one unique characteristic of glass, its capability for undistorted or controlled light transmittance, or transparency. Glass, in its basic form as annealed, untreated sheet, plate, or float glass, when compared to metals, is extremely notch-sensitive, has a low fracture resistance, has a low modulus of elasticity, and can be highly variable in its properties. While reasonably strong, it is not a desirable material for traditional aircraft applications because, as a solo component, it is heavy (about the same density as aluminum). In addition, when glass fails, it can break into extremely sharp fragments that have the potential for injury above and beyond simple impact, and have been known to be lethal.

    These special conditions address installing glass in much larger sizes than previously accepted and in a multitude of locations and applications, instead of using more traditional aircraft materials. In most, if not all cases, the glass will not be covered with a polycarbonate layer. Additionally, the retention of glass of this size and weight is not amenable to conventional techniques currently utilized in airplane cabins.

    These special conditions consider the unusual material properties of glass as an interior material that have limited or prevented its use in the past, and address the performance standards needed to ensure that those properties do not reduce the level of safety intended by the regulations. They address the use of large glass items installed in occupied rooms or areas during taxi, take off, and landing, or rooms or areas that occupants do have to enter or pass through to get to any emergency exit.

    These special conditions define a large glass component threshold of 4 kg, which is based on an assessment of the mass dislodged during a high ``g'' level (as defined in Sec. 25.562) event. Groupings of glass components that total more than 4 kg would also need to be included. The applicable performance standards in the regulations for the installation of these components also apply and should not adversely affect the standards provided below. For example, heat release and smoke density testing should not result in fragmentation of the component.

    For large glass components mounted in a cabin occupied by passengers or crew that are not otherwise protected from the injurious effects of failure of the glass component, the following apply:

    [[Page 1487]]

    Material. The glass used must be tempered or otherwise treated to ensure that when fractured, it breaks into small pieces with relatively dull edges. This must be demonstrated by testing to failure. Tests similar to ANSI/SAE Z26.1 section 5.7, Test 7 would be acceptable.

    Fragmentation. The glass component construction must control the fragmentation of the glass to minimize the danger from flying glass shards or pieces. Impact and puncture testing to failure must demonstrate this. Tests similar to ANSI/SAE Z26.1 section 5.9, Test 9 adjusted to ensure cracking the glass would be acceptable.

    Strength. The glass component, as installed in the airplane, must be strong enough to meet the load requirements for all flight and landing loads and all of the emergency landing conditions in subparts C and D of part 25. In addition, glass components that are located such that they are not protected from contact with cabin occupants must be designed for abusive loading without failure, such as impact from service carts, or occupants stumbling into, leaning against, sitting on, or performing other intentional or unintentional forceful contact. This must be demonstrated by static structural testing to ultimate load except that the critical loading condition must be tested to failure. The tested glass component must have all features that affect component strength, such as etched surfaces, cut or engraved designs, holes, and so forth.

    Retention. The glass component, as installed in the airplane, must not come free of its restraint or mounting system in the event of an emergency landing. Based on the characteristics of a large glass component, dynamic tests should be performed to demonstrate that the occupants would be protected up to the load levels required by the certification basis of the airplane. A single test for the most critical loading for the installed component would be sufficient. This may be accomplished by using already accepted methods for dynamic testing.

    Analysis may be used in lieu of testing if the applicant has validated the strength models and dynamic simulation models used, against static tests to failure and dynamic testing to the above requirements, and can predict structural failure and dynamic response and inertial load. The glass material properties must meet Sec. 25.613, ``Material strength properties and material design values.'' The effect of design details such as geometric discontinuities or surface finish must be accounted for in the test/analysis.

    Discussion of Comments

    Notice of proposed special conditions No. 25-05-08-SC for the Boeing Model 747-400 series airplanes was published in the Federal Register on August 11, 2005 (70 FR 46785). One commenter responded to the notice.

    Comment: The commenter expresses concern that the special conditions neglect to address injuries, especially head injuries to passengers because of physical movements of the airplane caused by unexpected disturbances, sudden loss of altitude, disorientation, etc.

    FAA Reply: The special conditions do not specifically call out for the protection of the passenger while moving about the cabin because the existing regulation, Sec. 25.785(d)(e), already addresses this requirement. These special conditions are additional requirements to the existing certification basis of the Boeing Model 747-400.

    Comment: The commenter expresses concern that the special conditions neglect to address injuries caused to passengers by glass breaking into a large number of small fragments. These small fragments may have dull edges and fall to the ground causing passengers to slip, fall, and harm themselves.

    FAA Reply: Special conditions 1 and 2 address this concern by requiring the glass to be tested to failure to demonstrate that glass pieces must be shown to be non-hazardous.

    Comment: The commenter expresses concern that the special conditions neglect to address disorientation of passengers because of reflections in mirrored glass panels, or because of intense sunlight through the windows on clear or mirrored glass panels.

    FAA Reply: In this case, glass does not present any additional hazards over the materials currently used in airplane interiors, such as polished metals or mirrored acrylics. The FAA is currently unaware of any instances of these materials causing such disorientation among the passengers.

    Comment: The commenter expresses concern that the special conditions neglect to address or omit the possible liability incurred by the carrier, operator, and potential third parties-not excluding the FAA, which is granting these special conditions. The commenter expresses concern that the liability incurred could be beyond the carrier's insurance coverage.

    FAA Reply: These special conditions are intended to establish a level of safety for the use of glass equal to those of the existing regulations. As such, the liability incurred would be no different than currently exists in the industry. The aircraft industry requested these special conditions, and they are required only if the applicant chooses to install structural glass.

    Applicability

    As discussed above, these special conditions are applicable to the Boeing Model 747-400 airplane. Should Lufthansa Technik apply at a later date for a change to the supplemental type certificate to include another model on the same type certificate incorporating the same novel or unusual design feature, these special conditions would apply to that model as well.

    Conclusion

    This action affects only certain novel or unusual design features on the Boeing Model 747-400 modified by Lufthansa Technik AG. It is not a rule of general applicability, and it affects only the applicant who applied to the FAA for approval of these features on the airplane.

    In an effort to address the commenters concerns, and based on the nature of the intended operation of the affected airplane, the FAA limits the application of these special conditions to airplanes operated for private use only. Therefore, the appropriate limitation has been added to the special conditions.

    List of Subjects in 14 CFR Part 25

    Aircraft, Aviation safety, Reporting and recordkeeping requirements.

    0 The authority citation for these special conditions is as follows:

    Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704.

    The Special Conditions

    0 Accordingly, pursuant to the authority delegated to me by the Administrator, the following special conditions are issued as part of the type certification basis for the Boeing Model 747-400 airplane, modified by Lufthansa Technik AG. For these special conditions, a large glass component is 4 kg (approximately 10 pounds) and greater in mass, or a grouping of glass components that total more than 4 kg.

  4. The airplane is not operated for hire or offered for common carriage. This provision does not preclude the operator from receiving remuneration to the extent consistent with 14 CFR parts 125 and 91, subpart F, as applicable.

  5. Material Fragmentation. The glass used to fabricate the component must be tempered or treated to ensure that when fractured, it breaks into small pieces with relatively dull edges. In addition, it must be shown that fragmentation of the glass is controlled to reduce the danger from flying glass shards or

    [[Page 1488]]

    pieces. This must be demonstrated by testing to failure.

  6. Component Strength. The glass component must be strong enough to meet the load requirements for all flight and landing loads including any of the applicable emergency landing conditions in subparts C & D of part 25. Abuse loading without failure, such as impact from occupants stumbling into, leaning against, sitting on, or performing other intentional or unintentional forceful contact must also be demonstrated. This must be demonstrated by static structural testing to ultimate load, except that the critical loading condition must be tested to failure in the as-installed condition. The tested glass must have all features that effect component strength, such as etched surfaces, cut or engraved designs, holes, and so forth. Glass pieces must be non-hazardous.

  7. Component Retention. The glass component, as installed in the airplane, must not come free of its restraint or mounting system in the event of an emergency landing. A test must be performed to demonstrate that the occupants would be protected from the effects of the component failing or becoming free of restraint under dynamic loading. The dynamic loading of Sec. 25.562(b)(2) is considered an acceptable dynamic event. The applicant may propose an alternate pulse, however, the impulse and peak load may not be less than that of Sec. 25.562(b)(2). As an alternative to a dynamic test, static testing may be used if the loading is assessed as equivalent or more critical than a dynamic test, based upon validated dynamic analysis. Both the primary directional loading and rebound conditions need to be assessed.

  8. Instruction for Continued Airworthiness. The instruction for continued airworthiness will reflect the fastening method used and will ensure the reliability of the methods used (e.g., life limit of adhesives, or clamp connection). Inspection methods and intervals will be defined based upon adhesion data from the manufacturer of the adhesive or actual adhesion test data, if necessary.

    Issued in Renton, Washington, on January 3, 2006. Kalene C. Yanamura, Acting Manager, Transport Airplane Directorate Aircraft Certification Service.

    [FR Doc. 06-200 Filed 1-9-06; 8:45 am]

    BILLING CODE 4910-13-P

VLEX uses login cookies to provide you with a better browsing experience. If you click on 'Accept' or continue browsing this site we consider that you accept our cookie policy. ACCEPT