Air pollution control; locomotives and locomotive engines: Equations, etc.; CFR correction,
[Federal Register: November 29, 2001 (Volume 66, Number 230)]
[Corrections]
[Page 59602-59608]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr29no01-69]
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Part 92
Control of Air Pollution From Locomotives and Locomotive Engines; Republication
CFR Correction
Editorial Note: On Monday, November 26, 2001, this rule document FR Doc. 01-55530appeared on 66 FR 58953-58964. Due to additional text being inadvertently added, it is being reprinted in its entirety.
In Title 40 of the Code of Federal Regulations, Parts 87 to 99, revised as of July 1, 2001, part 92 is corrected in Sec. 92.120 by revising equations (1) and (2) in paragraph (c)(2)(v), in Sec. 92.121 by revising paragraphs (b)(2)(vi), (b)(2)(ix), (b)(2)(xi)(A), and (b)(4)(iv), and by revising Sec. 92.132 to read as follows:
Sec. 92.120 NDIR analyzer calibration and checks.
* * * * *
(c)* * *
(2)* * *
(v)* * *
y = Ax4+ Bx3+ Cx2+ Dx + E (1) y = x/(Ax4+ Bx3+ Cx2+ Dx + E) (2)
where:
y = concentration. x = chart deflection.
* * * * *
Sec. 92.121 Oxides of nitrogen analyzer calibration and check.
* * * * *
(b)* * *
(2)* * *
(vi) Turn on the NOXgenerator O2(or air) supply and adjust the O2(or air) flow rate so that the NO indicated by the analyzer is about 10 percent less than indicated in step in paragraph (b)(2)(v) of this section. Record the concentration of NO in this NO + O2mixture. * * * * *
(ix) Switch off the NOXgeneration, but maintain gas flow through the system. The oxides of nitrogen analyzer will indicate the total NOXin the NO + O2mixture. Record this value. * * * * *
(xi)* * *
(A) Percent Efficiency=(1 + (a - b)/(c - d))(100)
where:
a=concentration obtained in paragraph (b)(2)(viii) of this section. b=concentration obtained in paragraph (b)(2)(ix) of this section. c=concentration obtained in paragraph (b)(2)(vi) of this section. d=concentration obtained in paragraph (b)(2)(vii) of this section.
* * * * *
(4)* * *
(iv) Calculate the concentration of the converter checking gas using the results from step in paragraph (b)(4)(iii) of this section and the converter efficiency from paragraph (b)(2) of this section as follows:
Concentration=(((X-Y)(100))/Efficiency) + Y
* * * * *
Sec. 92.132 Calculations.
(a) Duty-cycle emissions. This section describes the calculation of duty-cycle emissions, in terms of grams per brake horsepower hour (g/ bhp-hr). The calculation involves the weighted summing of the product of the throttle notch mass emission rates and dividing by the weighted sum of the brake horsepower. The final reported duty-cycle emission test results are calculated as follows:
(1)(i) Eidc=((Mij)(Fj))/ ((BHPj)(Fj))
Where:
Eidc=Duty-cycle weighted, brake-specific mass emission rate of pollutant i (i.e., HC, CO, NOXor PM and, if appropriate, THCE or NMHC) in grams per brake horsepower-hour; Mij=the mass emission rate pollutant i for mode j; Fj=the applicable weighting factor listed in Table B132-1 for mode j; BHPj=the measured brake horsepower for mode j.
(ii) Table B132-1 follows:
Table B132-1--Weighting Factors for Calculating Emission Rates
Locomotive not equipped Locomotive equipped with with multiple idle multiple idle notches Throttle notch setting
Test mode
notches
-------------------------
Line-haul Switch Line-haul Switch
Low Idle.......................................
1a
NA
NA
0.190
0.299
[[Page 59603]]
Normal Idle....................................
1
0.380
0.598
0.190
0.299 Dynamic Brake..................................
2
0.125
0.000
0.125
0.000 Notch 1........................................
3
0.065
0.124
0.065
0.124 Notch 2........................................
4
0.065
0.123
0.065
0.123 Notch 3........................................
5
0.052
0.058
0.052
0.058 Notch 4........................................
6
0.044
0.036
0.044
0.036 Notch 5........................................
7
0.038
0.036
0.038
0.036 Notch 6........................................
8
0.039
0.015
0.039
0.015 Notch 7........................................
9
0.030
0.002
0.030
0.002 Notch 8........................................
10
0.162
0.008
0.162
0.008
(2) Example: For the line-haul cycle, for locomotives equipped with normal and low idle, and with dynamic brake, the brake-specific emission rate for HC would be calculated as:
EHCdc=[(MHCla) (0.190) + (MHC1) (0.190) + (MHC2) (0.125) + (MHC3) (0.065) + (MHC4) (0.065) + (MHC5) (0.052) + (MHC6) (0.044) + (MHC7) (0.038) + (MHC8) (0.039) + (MHC9) (0.030) + (MHC10) (0.162)]/[(BHP1a) (0.190) + (BHP1) (0.190) + (BHP2) (0.125) + (BHP3) (0.065) + (BHP4) (0.065) + (BHP5) (0.052) + (BHP6) (0.044) + (BHP7) (0.038) + (BHP8) (0.039) + (BHP9) (0.030) + (BHP10) (0.162)]
(3) In each mode, brake horsepower output is the power that the engine delivers as output (normally at the flywheel), as defined in Sec. 92.2.
(i) For locomotive testing (or engine testing using a locomotive alternator/generator instead of a dynamometer), brake horsepower is calculated as:
BHP=HPout/Aeff+ HPacc
Where:
HPout=Measured horsepower output of the alternator/ generator. Aeff=Efficiency of the alternator/generator. HPacc=Accessory horsepower.
(ii) For engine dynamometer testing, brake horsepower is determined from the engine speed and torque.
(4) For locomotive equipped with features that shut the engine off after prolonged periods of idle, the measured mass emission rate Mi1(and Mi1aas applicable) shall be multiplied by a factor equal to one minus the estimated fraction reduction in idling time that will result in use from the shutdown feature. Application of this adjustment is subject to the Administrator's approval.
(b) Throttle notch emissions. This paragraph (b) describes the calculation of throttle notch emissions for all operating modes, including: idle (normal and low, as applicable); dynamic brake; and traction power points. The throttle notch (operating mode) emission test results, final reported values and values used in paragraph (a)(1) of this section are calculated as follows:
(1) Brake specific emissions (Eij) in grams per brake horsepower-hour of each species i (i.e., HC, CO, NOXor PM and, if appropriate, THCE or NMHC) for each mode j:
(i) EHC mode=HC grams/BHP-hr=MHC mode/ Measured BHP in mode.
Where:
MHC mode=Mass HC emissions (grams per hour) for each test mode.
(ii) ETHCE mode=THCE grams/BHP-hr=MTHCE mode/ Measured BHP in mode.
Where:
MTHCE mode(Total hydrocarbon equivalent mass emissions (grams per hour) for each test mode): =MHCj+ (Mij) (MWCp)/ MWCi Mij=the mass emission rate oxygenated pollutant i for mode j. MWCi=the molecular weight of pollutant i divided by the number of carbon atoms per molecule of pollutant i. MWCp=the molecular weight of a typical petroleum fuel component divided by the number of carbon atoms per molecule of a typical petroleum fuel component=13.8756.
(iii) ENMHC mode=NMHC grams/BHP- hr=MNMHC mode/Measured BHP in mode.
Where:
MNMHC mode=Mass NMHC emissions (grams per hour) for each test mode.
(iv) ECO mode=CO grams/BHP-hr=MCO mode/ Measured BHP in mode.
Where:
MCO mode=Mass CO emissions (grams per hour) for each test mode.
(v) ENOx mode=NOXgrams/BHP- hr=MNOx mode/Measured BHP in mode.
Where:
MNOx mode=Mass NOXemissions (grams per hour) for each test mode.
(vi) EPM mode=PM grams/BHP-hr=MPM mode/ Measured BHP in mode.
Where:
MPM mode=Mass PM emissions (grams per hour) for each test mode.
(vii) EAL mode=Aldehydes grams/BHP- hr=MAL mode/Measured BHP in mode.
(vii) EAL mode=Aldehydes grams/BHP- hr=MAL mode/Measured BHP in mode.
Where:
MAL mode=Total aldehyde mass emissions (grams per hour) for each test mode.
(2) Mass Emissions--Raw exhaust measurements. For raw exhaust measurements mass emissions (grams per hour) of each species for each mode:
(i) General equations. (A) The mass emission rate, MX mode(g/hr), of each pollutant (HC, NOX, CO2, CO, CH4CH3OH, CH3CH2OH, CH2O, CH3CH2O) for each operating mode for raw measurements is determined based on one of the following equations:
MX mode=(DX/106)(DVol)(MWX/ Vm) MX mode=(WX/106)(WVol)(MWX/ Vm)
Where:
X designates the pollutant (e.g., HC), DX is the concentration of pollutant X (ppm or ppmC) on a dry basis, MWXis the molecular weight of the pollutant (g/mol), DVol is the total exhaust flow rate (ft3/hr) on a dry basis, WX is the concentration of pollutant X (ppm or ppmC) on a wet basis, WVol is the total exhaust flow rate (ft3/hr) on a wet basis, Vmis the volume of one mole of gas at standard temperature and pressure (ft3/mol).
(B) All measured volumes and volumetric flow rates must be corrected to standard temperature and pressure prior to calculations.
(ii) The following abbreviations and equations apply to this paragraph (b)(2):
=Atomic hydrogen/carbon ratio of the fuel. =Atomic oxygen/carbon ratio of the fuel. CMWf=Molecular weight of the fuel per carbon atom, or carbon molecular weight (g/moleC)=(12.011 + 1.008+ 16.000). DCO=CO concentration in exhaust, ppm (dry). DCO2=CO2concentration in exhaust, percent (dry). DHC=HC carbon concentration in exhaust, ppm C (dry).
[[Page 59604]]
DNOX=NOXconcentration in exhaust, in ppm (dry). DVol=Total exhaust flow rate (ft3/hr) on a dry basis; or =(Vm)(Wf)/((CMWf) (DHC/ 106+ DCO/106+ DCO2/100)). K=Water gas equilibrium constant=3.5. Kw=Wet to dry correction factor. MF=Mass flow-rate of fuel used in the engine in lb/ hr=Wf/453.59. MWC=Atomic weight of carbon=12.011. MWCO=Molecular weight of CO=28.011. MWH=Atomic weight of hydrogen=1.008. MWNO2=Molecular weight of nitrogen dioxide (NO2)=46.008. MWO=Molecular weight of atomic oxygen=16.000. T=Temperature of inlet air ( deg.F). Vm=Volume of one mole of gas at standard temperature and pressure (ft3/mole). Wf=Mass flow-rate of fuel used in the engine, in grams/ hr=(453.59) x (Mflbs/hr). WCO2=CO2concentration in exhaust, percent (wet). WHC=HC concentration in exhaust, ppm C (wet). WVol=Total exhaust flow rate (ft3/hr) on a wet basis; or =(Vm)(Wf)/((CMWf)(WHC/ 106+ WCO/106WCO2/100)).
(iii) Calculation of individual pollutant masses. Calculations for mass emission are shown here in multiple forms. One set of equations is used when sample is analyzed dry (equations where the concentrations are expressed as DX), and the other set is used when the sample is analyzed wet (equations where the concentrations are expressed as WX). When samples are analyzed for some constituents dry and for some constituents wet, the wet concentrations must be converted to dry concentrations, and the equations for dry concentrations used. Also, the equations for HC, NMHC, CO, and NOXhave multiple forms that are algebraically equivalent: An explicit form that requires intermediate calculation of Vmand DVol or WVol; and an implicit form that uses only the concentrations (e.g., DCO) and the mass flow rate of the fuel. For these calculations, either form may be used.
(A) Hydrocarbons and nonmethane hydrocarbons.
(1) Hydrocarbons. (i) For petroleum-fueled engines:
MHC mode =(DHC)CMWf(DVol)(106)/Vm =((DHC/106)(Wf)/((DCO/106) + (DCO2/100) + (DHC/106) + (DX/ 106))) MHC mode
=(WHC)CMWf(WVol)(106)/Vm
=((WHC/106)(Wf)/((WCO/106) + (WCO2/100) + (WHC/106) + ((WX/ 106)))
(ii) For alcohol-fueled engines:
DHC=FID HC - (rx)(DX) WHC=FID HC - (rx)(WX)
Where:
FID HC=Concentration of ``hydrocarbon'' plus other organics such as methanol in exhaust as measured by the FID, ppm carbon equivalent. rx=FID response to oxygenated species x (methanol, ethanol, or acetaldehyde). DX=Concentration of oxygenated species x (methanol, ethanol, or acetaldehyde) in exhaust as determined from the dry exhaust sample, ppm carbon (e.g., DCH3OH, 2(DCH3CH2OH)). WX=Concentration of oxygenated species x (methanol, ethanol, or acetaldehyde) in exhaust as determined from the wet exhaust sample, ppm carbon. DX=The sum of concentrations DX for all oxygenated species. WX=The sum of concentrations WX for all oxygenated species.
(2) Nonmethane hydrocarbons:
MNMHC mode=(DNMHC)CMWf(DVol) (106)/ Vm =((DNMHC/106)(Wf)/((DCO/106) + (DCO2/100) + (DHC/106))) MNMHC mode=(WNMHC)CMWf(WVol) (106)/ Vm =((WNMHC/106)(Wf)/((WCO/106) + (WCO2/100) + (WHC/106)))
Where:
DNMHC=FID HC - (rCH4)(DCH4) WNMHC=FID HC - (rCH4)(WCH4) FID HC=Concentration of ``hydrocarbon'' plus other organics such as methane in exhaust as measured by the FID, ppm carbon equivalent. rCH4=FID response to methane. DCH4=Concentration of methane in exhaust as determined from the dry exhaust sample, ppm. WCH4=Concentration of methane in exhaust as determined from the wet exhaust sample, ppm.
(B) Carbon monoxide:
MCO mode=(DCO)MWCO(DVol)/106/ Vm =((MWCO(DCO/106)(Wf)/ ((CMWf)(DCO/106) + (DCO2/100) + DHC/ 106) + (DX/106))) MCO mode=(WCO)MWCO(DVol)(106)/ Vm + ((MWCO(WCO/106)(Wf)/ ((CMWf)(WCO/106) + (WCO2/100) + WHC/ 106) + (WX/106)))
(C) Oxides of nitrogen:
MNOx mode=(DNOX)MWNO2(DVol)(106)/ Vm =((MWNO2(DNOX/106)(Wf)/ ((CMWf)(DCO/106) + (DCO2/100) + (DHC/ 106) + (DX/106))) MNOx mode=(WNOX)MWNO2(DVol)(106)/ Vm =((MWNO2(WNOX/106)(Wf)/ ((CMWf)(WCO/106) + (WCO2/100) + (WHC/ 106) + (WX/106)))
(D) Methanol:
MCH3OH mode=(DCH3OH/106)32.042(DVol)/ Vm MCH3OH mode=(WCH3OH/106)32.042(WVol)/ Vm
Where:
DCH3OH=(Vm)(106)[(C1x AV1 ) + (C2x AV2)]/DVolMS. WCH3OH=(Vm)(106)[(C1x AV1 ) + (C2x AV2)]/WVolMS. Ci=concentration of methanol in impinger i (1 or 2) in mol/ml. AVi=Volume of absorbing reagent in impinger i (1 or 2) in ml. DVolMS=Volume (standard ft3) of exhaust sample drawn through methanol impingers (dry). WVolMS=Volume (standard ft3) of exhaust sample drawn through methanol impingers (wet).
(E) Ethanol:
MCH3CH2OH mode=(DCH3CH2OH/106)23.035(DVol)/ Vm MCH3CH2OH mode= (WCH3CH2OH/106)23.035(WVol)/ Vm
Where:
DCH3CH2OH=(Vm)(106)[(C1x AV1 ) + (C2x AV2)]/DVolES. WCH3CH2OH=(Vm)(106)
[(C1x AV1) + (C2x AV2)] /WVolES. Ci=concentration of ethanol in impinger i (1 or 2) in mol/ml. AVi=Volume of absorbing reagent in impinger i (1 or 2) in ml. DVolES=Volume (standard ft3) of exhaust sample drawn through ethanol impingers (dry). WVolES=Volume (standard ft3) of exhaust sample drawn through ethanol impingers (wet).
(F) Formaldehyde:
MCH2O mode=(DCH2O/106)30.026(DVol)/Vm MCH2O mode=(WCH2O/106)30.026(WVol)/Vm
(1) If aldehydes are measured using impingers:
DCH2O=(Vm)(106)[(C1x AV1) + (C2x AV2)]/DVolFS WCH2O=(Vm)(106)[(C1x AV1) + (C2x AV2)]/WVolFS
(2) If aldehydes are measured using cartridges:
DCH2O=(Vm)(106)(CRx AVR)/ DVolFS
WCH2O=(Vm)(106)(CRx AVR)/ WVolFS
(3) The following definitions apply to this paragraph (b)(2)(iii)(F):
AVi=Volume of absorbing reagent in impinger i (1 or 2) in ml. AVR=Volume of absorbing reagent use to rinse the cartridge in ml. Ci=concentration of formaldehyde in impinger i (1 or 2) in mol/ml. CR=concentration of formaldehyde in solvent rinse in mol/ ml. DVolFS=Volume (standard ft3) of exhaust sample drawn through formaldehyde sampling system (dry). WVolFS=Volume (standard ft3) of exhaust sample drawn through formaldehyde sampling system (wet).
(G) Acetaldehyde:
MCH3CHO mode=(DCH3CHO/106)27.027(DVol)/ Vm
[[Page 59605]]
MCH3CHO mode=(WCH3CHO/106)27.027(WVol)/ Vm
(1) If aldehydes are measured using impingers:
DCH3CHO=(Vm)(106)[(C1x AV1) + (C2x AV2)]/DVolAS
WCH3CHO=(Vm)(106)[(C1x AV1) + C2x AV2)]/WVolAS
(2) If aldehydes are measured using cartridges:
DCH3CHO=(Vm)(106)(CRx AVR)/ DVolAS WCH3CHO=(Vm)(106)(CRx AVR)/ WVolAS
(3) The following definitions apply to this paragraph (b)(2)(iii)(G):
AVi=Volume of absorbing reagent in impinger i (1 or 2) in ml. AVR=Volume of absorbing reagent use to rinse the cartridge in ml. Ci=concentration of acetaldehyde in impinger i (1 or 2) in mol/ml. CR=concentration of acetaldehyde in solvent rinse in mol/ ml. DVolAS=Volume (standard ft3) of exhaust sample drawn through acetaldehyde sampling system (dry). WVolAS=Volume (standard ft3) of exhaust sample drawn through acetaldehyde sampling system (wet).
(iv) Conversion of wet concentrations to dry concentrations. Wet concentrations are converted to dry concentrations using the following equation:
DX=KWWX
Where:
WX is the concentration of species X on a wet basis. DX is the concentration of species X on a dry basis. KWis a conversion factor=WVol/DVol=1 + DH2O.
(A) Iterative calculation of conversion factor. The conversion factor KWis calculated from the fractional volume of water in the exhaust on a dry basis (DH2O=volume of water in exhaust/dry volume of exhaust). Precise calculation of the conversion factor KWmust be done by iteration, since it requires the dry concentration of HC, but HC emissions are measured wet.
(1) The conversion factor is calculated by first assuming DHC=WHC to calculate DVol:
DVol=(Vm)(Wf)/((CMWf)(DHC/ 106+ DCO/106+ DCO2/100))
(2) This estimate is then used in the following equations to calculate DVolair, then DH2O, then KW, which allows DHC to be determined more accurately from WHC:
[GRAPHIC] [TIFF OMITTED] TR16AP98.009
Where:
Y=Water volume concentration in intake air, volume fraction (dry). DVolair=Air intake flow rate (ft3/hr) on a dry basis, measured, or calculated as:
[GRAPHIC] [TIFF OMITTED] TR16AP98.010
(3) The calculations are repeated using this estimate of DHC. If the new estimate for KWis not within one percent of the previous estimate, the iteration is repeated until the difference in KWbetween iterations is less than one percent.
(B) Alternate calculation of DH2O (approximation). The following approximation may be used for DH2O instead of the calculation in paragraph (b)(2)(iv)(A) of this section:
[GRAPHIC] [TIFF OMITTED] TR16AP98.011
Where:
[GRAPHIC] [TIFF OMITTED] TR16AP98.012
Y=Water volume concentration in intake air, volume fraction (dry).
(3) Mass Emissions--Dilute exhaust measurements. For dilute exhaust measurements mass emissions (grams per hour) of each species for each mode:
(i) General equations. The mass emission rate, Mx mode (g/hr) of each pollutant (HC, NOX, CO2, CO, CH4 CH3OH, CH3CH2OH, CH2O, CH3CH2O) for each operating mode for bag measurements and diesel continuously heated sampling system measurements is determined from the following equation:
Mx mode=(Vmix)(Densityx)(Xconc )/(Vf)
Where:
x designates the pollutant (e.g., HC), Vmixis the total diluted exhaust volumetric flow rate (ft3/hr), Densityxis the specified density of the pollutant in the gas phase (g/ft3), Xconcis the fractional concentration of pollutant x (i.e., ppm/106, ppmC/ 106, or %/100), and Vfis the fraction of the raw exhaust that is diluted for analysis.
[[Page 59606]]
(ii) The following abbreviations and equations apply to paragraphs (b)(3)(i) through (b)(3)(iii)(J) of this section:
(A) DF=Dilution factor, which is the volumetric ratio of the dilution air to the raw exhaust sample for total dilution, calculated as:
[GRAPHIC] [TIFF OMITTED] TR16AP98.013
Where:
WCO2=Carbon dioxide concentration of the raw exhaust sample, in percent (wet). WCO2e=Carbon dioxide concentration of the dilute exhaust sample, in percent (wet). WCO2d=Carbon dioxide concentration of the dilution air, in percent (wet).
(B) Vmix=Diluted exhaust volumetric flow rate in cubic feet per hour corrected to standard conditions (528 deg.R, and 760 mm Hg).
(C) Vf=Fraction of the total raw exhaust that is diluted for analysis.
=((CO2conc/102) + (COconc/ 106) + (HCconc/ 106))(Vmix)(CMWf)/Vm/ Mf
(iii) Calculation of individual pollutants.
(A) MHC mode=Hydrocarbon emissions, in grams per hour by mode, are calculated using the following equations:
MHC mode=(Vmix)(DensityHC)(HCconc /106)/Vf HCconc=HCe- (HCd)(1 - (1/DF)) HCe=FID HCe- (rx)(Xe)
Where:
DensityHC=Density of hydrocarbons=16.42 g/ft3 (0.5800 kg/m3) for #l petroleum diesel fuel, 16.27 g/ ft3(0.5746 kg/m3) for #2 diesel, and 16.33 g/ ft3(0.5767 kg/m3) for other fuels, assuming an average carbon to hydrogen ratio of 1:1.93 for #1 petroleum diesel fuel, 1:1.80 for #2 petroleum diesel fuel, and 1:1.85 for hydrocarbons in other fuels at standard conditions. HCconc=Hydrocarbon concentration of the dilute exhaust sample corrected for background, in ppm carbon equivalent (i.e., equivalent propane x 3). HCe=Hydrocarbon concentration of the dilute exhaust bag sample, or for diesel continuous heated sampling systems, average hydrocarbon concentration of the dilute exhaust sample as determined from the integrated HC traces, in ppm carbon equivalent. For petroleum-fueled engines, HCeis the FID measurement. For methanol-fueled and ethanol-fueled engines: FID HCe=Concentration of hydrocarbon plus methanol, ethanol and acetaldehyde in dilute exhaust as measured by the FID, ppm carbon equivalent. rx=FID response to oxygenated species x (methanol, ethanol or acetaldehyde). Xe=Concentration of species x (methanol, ethanol or acetaldehyde) in dilute exhaust as determined from the dilute exhaust sample, ppm carbon. HCd=Hydrocarbon concentration of the dilution air as measured, in ppm carbon equivalent.
(B) MNOx mode= Oxides of nitrogen emissions, in grams per hour by mode, are calculated using the following equations:
MNOx mode=(Vmix) (DensityNO2) (NOxconc/10 \6\) /Vf NOxconc=(NOxe- NOxd(1 - (1/DF)))
Where:
DensityNO2=Density of oxides of nitrogen is 54.16 g/ft\3\ (1.913 kg/m\3\), assuming they are in the form of nitrogen dioxide, at standard conditions. NOxconc=Oxides of nitrogen concentration of the dilute exhaust sample corrected for background, in ppm. NOxe=Oxides of nitrogen concentration of the dilute exhaust bag sample as measured, in ppm. NOxd=Oxides of nitrogen concentration of the dilution air as measured, in ppm.
(C) MCO2 mode=Carbon dioxide emissions, in grams per hour by mode, are calculated using the following equations:
MCO2 mode=(Vmix) (Density CO2) (CO2conc/10\2\) /Vf
CO2conc=CO2e- CO2d(1 - (1/DF))
Where:
Density CO2=Density of carbon dioxide is 51.81 g/ft\3\ (1.830 kg/m\3\), at standard conditions. CO2conc=Carbon dioxide concentration of the dilute exhaust sample corrected for background, in percent. CO2e=Carbon dioxide concentration of the dilute exhaust bag sample, in percent. CO2d=Carbon dioxide concentration of the dilution air as measured, in percent.
(D)(1) MCO mode=Carbon monoxide emissions, in grams per hour by mode, are calculated using the following equations:
MCO mode=(Vmix)(DensityCO)(COconc /10\6\)/Vf
COconc=COe- COd(1 - (1/DF))
COd=(1 - 0.000323R)COdm
Where:
DensityCO=Density of carbon monoxide is 32.97 g/ft\3\ (1.164 kg/m\3\), at standard conditions. COconc=Carbon monoxide concentration of the dilute exhaust sample corrected for background, water vapor, and CO2extraction, ppm. COe=Carbon monoxide concentration of the dilute exhaust sample volume corrected for water vapor and carbon dioxide extraction, in ppm. COe=(1 - (0.01+ 0.005/)CO2e- 0.000323RH)COem, where is the hydrogen to carbon ratio as measured for the fuel used. COem=Carbon monoxide concentration of the dilute exhaust sample as measured, in ppm. RH = Relative humidity of the dilution air, percent. COd=Carbon monoxide concentration of the dilution air corrected for water vapor extraction, in ppm. COdm=Carbon monoxide concentration of the dilution air sample as measured, in ppm.
(2) If a CO instrument which meets the criteria specified in Sec. 86.1311 of this chapter is used and the conditioning column has been deleted, COemmust be substituted directly for COe, and COdmmust be substituted directly for COd.
(E) MCH4 mode=Methane emissions corrected for background, in gram per hour by mode, are calculated using the following equations:
MCH4 mode=(Vmix) (DensityCH4) (CH4conc/10\6\) /Vf CH4conc=CCH4e- CCH4d(1 - (1/DF))
Where:
DensityCH4=Density of methane is 18.89 g/ft\3\ at 68 deg.F (20 deg.C) and 760 mm Hg (101.3kPa) pressure. CH4conc=Methane concentration of the dilute exhaust corrected for background, in ppm. CCH4e=Methane concentration in the dilute exhaust, in ppm. CCH4d=Methane concentration in the dilution air, in ppm.
(F) MCH3OH mode=Methanol emissions corrected for background, in gram per hour by mode, are calculated using the following equations:
MCH3OH mode=(Vmix)(DensityCH3OH) (CH3OHconc/10\6\)/Vf CH3OHconc=CCH3OHe- CCH3OHd(1 - (1/ DF)) CCH3OHe=((3.817)(10- 2)(TEM) (((CS1)(AVS1)) + (CS2) (AVS2)))/((PB)(VEM)) CCH3OHd=((3.817)(10-2)(TDM)(((CD1 ) (AVD1)) + (CD2) (AVD2)))/ ((PB)(VDM))
Where:
DensityCH3OH=Density of methanol is 37.71 g/ft\3\ (1.332 kg/m\3\), at 68 deg.F (20 deg.C) and 760 mm Hg (101.3kPa) pressure. CH3OHconc=Methanol concentration of the dilute exhaust corrected for background, in ppm. CCH3OHe=Methanol concentration in the dilute exhaust, in ppm. CCH3OHd=Methanol concentration in the dilution air, in ppm. TEM=Temperature of methanol sample withdrawn from dilute exhaust, deg.R. TDM=Temperature of methanol sample withdrawn from dilution air, deg.R. PB=Barometric pressure during test, mm Hg. VEM=Volume of methanol sample withdrawn from dilute exhaust, ft \3\. VDM=Volume of methanol sample withdrawn from dilution air, ft \3\. CS=GC concentration of aqueous sample drawn from dilute exhaust, g/ml. CD=GC concentration of aqueous sample drawn from dilution air, g/ml. AVS=Volume of absorbing reagent (deionized water) in impinger through which methanol sample from dilute exhaust is drawn, ml. AVD=Volume of absorbing reagent (deionized water) in impinger through which methanol sample from dilution air is drawn, ml.
1=first impinger.
[[Page 59607]]
2=second impinger.
(G) MC2H5OH mode=Ethanol emissions corrected for background, in gram per hour by mode, are calculated using the following equations:
MCH3CH2OH mode=(Vmix)(DensityCH3CH2OH) ((CH3CH2OHconc/10 \6\))/Vf CH3CH2OHconc=CCH3CH2OHe- CCH3CH2OHd(1 - (1/DF)) CCH3CH2OHd=((2.654)(10- 2)(TDM)(((CD1 )(AVD1)) + (CD2)(AVD2)))/ ((PB)(VDM)) CCH3CH2OHe=((2.654)(10- 2)(TEM)(((CS1)(AVS1)) + (CS2)(AVS2)))/((PB)(VEM))
Where:
DensityC2H5OH=Density of ethanol is 54.23 g/ft \3\ (1.915 kg/m \3\), at 68 deg.F (20 deg.C) and 760 mm Hg (101.3kPa) pressure. CH3CH2OHconc=Ethanol concentration of the dilute exhaust corrected for background, in ppm. CCH3CH2OHe=Ethanol concentration in the dilute exhaust, in ppm. CCH3CH2OHd=Ethanol concentration in the dilution air, in ppm. TEM= Temperature of ethanol sample withdrawn from dilute exhaust, deg.R. TDM=Temperature of ethanol sample withdrawn from dilution air, deg.R. PB=Barometric pressure during test, mm Hg. VEM=Volume of ethanol sample withdrawn from dilute exhaust, ft \3\. VDM=Volume of ethanol sample withdrawn from dilution air, ft \3\. CS=GC concentration of aqueous sample drawn from dilute exhaust, g/ml. CD=GC concentration of aqueous sample drawn from dilution air, g/ml. AVS= Volume of absorbing reagent (deionized water) in impinger through which ethanol sample from dilute exhaust is drawn, ml. AVD=Volume of absorbing reagent (deionized water) in impinger through which ethanol sample from dilution air is drawn, ml.
1=first impinger.
2=second impinger.
(H) MCH2O mode=Formaldehyde emissions corrected for background, in gram per hour by mode, are calculated using the following equations:
MCH2O mode=(Vmix)(DensityCH2O) ((CH2Oconc/10 \6\)/Vf CH2Oconc=CCH2Oe- CCH2Od(1 - (1/DF)) CCH2Oe=((4.069)(10-2)(CFDE)(VAE ) (Q)(TEF))/((VSE)(PB) CCH2Od=((4.069)(10- 2)(CFDA)(VAA )(Q)(TDF))/(VSA)(PB)
Where:
DensityCH2O=Density of formaldehyde is 35.36 g/ft \3\ (1.249 kg/m \3\), at 68 deg.F (20 deg.C) and 760 mmHg (101.3 kPa) pressure. CH2Oconc=Formaldehyde concentration of the dilute exhaust corrected for background, ppm. CCH2Oe=Formaldehyde concentration in dilute exhaust, ppm. CCH2Od=Formaldehyde concentration in dilution air, ppm.
CFDE=Concentration of DNPH derivative of formaldehyde from dilute exhaust sample in sampling solution, g/ml.
VAE=Volume of sampling solution for dilute exhaust formaldehyde sample, ml.
Q = Ratio of molecular weights of formaldehyde to its DNPH derivative = 0.1429.
TEF=Temperature of formaldehyde sample withdrawn from dilute exhaust, deg.R.
VSE=Volume of formaldehyde sample withdrawn from dilute exhaust, ft3.
PB=Barometric pressure during test, mm Hg.
CFDA=Concentration of DNPH derivative of formaldehyde from dilution air sample in sampling solution, g/ml.
VAA=Volume of sampling solution for dilution air formaldehyde sample, ml.
TDF=Temperature of formaldehyde sample withdrawn from dilution air, deg.R.
VSA=Volume of formaldehyde sample withdrawn from dilution air, ft3.
(I) MCH3CHO mode=Acetaldehyde emissions corrected for background, in grams per hour by mode, are calculated using the following equations:
MCH3CHO mode= (Vmix)(DensityCH3CHO)((CH3CHOconc /106)/Vf CH3CHOconc=CCH3CHOe- CCH3CHOd(1--(1/ DF)) CCH3CHOe=((2.774)(10- 2) (CADE)(VAE)(Q)(TEF))/ ((VSE)(PB) CCH3CHOd=((2.774)(10- 2) (CADA)(VAA)(Q)(TDF))/ (VSA)(PB)
Where:
Density CH3CHO=Density of acetaldehyde is 51.88 g/ ft3(1.833 kg/m3), at 68 deg.F (20 deg.C) and 760 mmHg (101.3 kPa) pressure. CH3CHOconc=Acetaldehyde concentration of the dilute exhaust corrected for background, ppm. CCH3CHOe=Acetaldehyde concentration in dilute exhaust, ppm. CCH3CHOd=Acetaldehyde concentration in dilution air, ppm. CADE=Concentration of DNPH derivative of acetaldehyde from dilute exhaust sample in sampling solution, g/ml. VAE=Volume of sampling solution for dilute exhaust acetaldehyde sample, ml. Q=Ratio of molecular weights of acetaldehyde to its DNPH derivative =0.182 TEF=Temperature of acetaldehyde sample withdrawn from dilute exhaust, deg.R. VSE=Volume of acetaldehyde sample withdrawn from dilute exhaust, ft3. PB=Barometric pressure during test, mm Hg. CADAConcentration of DNPH derivative of acetaldehyde from dilution air sample in sampling solution, g/ml. VAA=Volume of sampling solution for dilution air acetaldehyde sample, ml. TDF=Temperature of acetaldehyde sample withdrawn from dilution air, deg.R. VSA=Volume of acetaldehyde sample withdrawn from dilution air, ft3.
(J) MNMHC mode=Nonmethane hydrocarbon emissions, in grams per hour by mode.
MNMHC mode=(Vmix)(DensityNMHC) ((NMHCEconc/106))/Vf NMHCconc=NMHCe--(NMHCd)(1 - (1/DF)) NMHCe=FID HCe- (rm)(CCH4e) NMHCd=FID HCd- (rm)(CCH4d)
Where:
DensityNMHC=Density of nonmethane hydrocarbons=16.42 g/ ft3(0.5800 kg/m3) for # 1 petroleum diesel fuel, 16.27 g/ft3(0.5746 kg/m3) for #2 diesel, and 16.33 for other fuels, assuming an average carbon to hydrogen ratio of 1:1.93 for #1 petroleum diesel fuel, 1:1.80 for #2 petroleum diesel fuel, and 1:1.85 for nonmethane hydrocarbons in other fuels at standard conditions. NMHCconc=Nonmethane hydrocarbon concentration of the dilute exhaust sample corrected for background, in ppm carbon equivalent (i.e., equivalent propane x 3). NMHCe=Nonmethane hydrocarbon concentration of the dilute exhaust bag sample: FID HCe=Concentration of hydrocarbons in dilute exhaust as measured by the FID, ppm carbon equivalent. rm=FID response to methane. CCH4e=Concentration of methane in dilute exhaust as determined from the dilute exhaust sample. NMHCd=Nonmethane hydrocarbon concentration of the dilution air: FID HCd=Concentration of hydrocarbons in dilute exhaust as measured by the FID, ppm carbon equivalent. rm=FID response to methane. CCH4d=Concentration of methane in dilute exhaust as determined from the dilute exhaust sample, ppm.
(4) Particulate exhaust emissions. The mass of particulate for a test mode determined from the following equations when a heat exchanger is used (i.e., no flow compensation), and when background filters are used to correct for background particulate levels:
MPM mode=Particulate emissions, grams per hour by mode. MPM mode=(WVol)(PMconc)(1 + DF)=(Vmix)(PMconc)/Vf PMconc=PMe- PMd(1 - (1/DF)) PMe=MPMe/Vsampe/10 \3\ PMd=MPMd/Vsampd/10 \3\
Where:
PMconc=Particulate concentration of the diluted exhaust sample corrected for background, in g/ft \3\ MPMe=Measured mass of particulate for the exhaust sample, in mg, which is the difference in filter mass before and after the test. MPMd=Measured mass of particulate for the dilution air sample, in mg, which is the difference in filter mass before and after the test. Vsampe=Total wet volume of sample removed from the dilution tunnel for the exhaust particulate measurement, cubic feet at standard conditions. Vsampd=Total wet volume of sample removed from the dilution tunnel for the dilution air particulate measurement, cubic feet at standard conditions. DF=Dilution factor, which is the volumetric ratio of the dilution air to the raw exhaust sample, calculated as:
[[Page 59608]]
[GRAPHIC] [TIFF OMITTED] TR16AP98.014
(c) Humidity calculations. (1) The following abbreviations (and units) apply to paragraph (b) of this section:
BARO=barometric pressure (Pa). H=specific humidity, (g H2O/g of dry air). KH=conversion factor=0.6220 g H2O/g dry air. Mair=Molecular weight of air=28.9645. MH2O=Molecular weight of water=18.01534. PDB=Saturation vapor pressure of water at the dry bulb temperature (Pa). PDP=Saturation vapor pressure of water at the dewpoint temperature (Pa). Pv=Partial pressure of water vapor (Pa). PWB=Saturation vapor pressure of water at the wet bulb temperature (Pa). TDB=Dry bulb temperature (Kelvin). TWB=Wet bulb temperature (Kelvin). Y=Water-vapor volume concentration.
(2) The specific humidity on a dry basis of the intake air (H) is defined as:
H=((KH) (Pv)/(BARO - Pv))
(3) The partial pressure of water vapor may be determined using a dew point device. In that case:
Pv=PDP
(4) The percent of relative humidity (RH) is defined as:
RH=(Pv/PDB)100
(5) The water-vapor volume concentration on a dry basis of the engine intake air (Y) is defined as:
Y=((H)(Mair)/(MH2O)=Pv/(BARO - Pv)
(d) NOXcorrection factor. (1) NOXemission rates (MNOx mode) shall be adjusted to account for the effects of humidity and temperature by multiplying each emission rate by KNOx, which is calculated from the following equations:
KNOx=(K)(1 + (0.25(logK)2)1/2) K=(KH)(KT) KH=[C1+ C2(exp(( - 0.0143)(10.714))]/
[C1+ C2(exp(( - 0.0143)(1000H))]
C1= - 8.7 + 164.5exp( - 0.0218(A/F)wet) C2=130.7 + 3941exp( - 0.0248(A/F)wet)
Where:
(A/F)wet=Mass of moist air intake divided by mass of fuel intake. KT=1/[1-0.017(T30-TA)] for tests conducted at ambient temperatures below 30 deg.C. KT=1.00 for tests conducted at ambient temperatures at or above 30 deg.C. T30=The measured intake manifold air temperature in the locomotive when operated at 30 deg.C (or 100 deg.C, where intake manifold air temperature is not available). TA=The measured intake manifold air temperature in the locomotive as tested (or the ambient temperature ( deg.C), where intake manifold air temperature is not available).
(e) Other calculations. Calculations other than those specified in this section may be used with the advance approval of the Administrator.
[FR Doc. 01-55530Filed11-23-01; 8:45 am]
Editorial Note: On Monday, November 26, 2001, this rule document FR Doc. 01-55530appeared on 66 FR 58953-58964. Due to additional text being inadvertently added, it is being reprinted in its entirety.
[FR Doc. R1-55530Filed11-28-01; 8:45 am]
BILLING CODE 1505-01-D
