Separate Parts In This Issue Part III Environmental Protection Agency,
[Federal Register: May 30, 2007 (Volume 72, Number 103)]
[Proposed Rules]
[Page 30168-30207]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr30my07-28]
[[Page 30168]]
ENVIRONMENTAL PROTECTION AGENCY
[EPA-HQ-OAR-2002-0064; FRL-8316-7]
RIN 2060-AK26
Protection of Stratospheric Ozone: Listing of Substitutes for Ozone-Depleting Substances--n-Propyl Bromide in Adhesives, Coatings, and Aerosols
AGENCY: Environmental Protection Agency.
ACTION: Notice of Proposed Rulemaking.
SUMMARY: Pursuant to the U.S. Environmental Protection Agency's (EPA or ``we'') Significant New Alternatives Policy (SNAP) program, this action proposes to list n-propyl bromide (nPB) as an unacceptable substitute for methyl chloroform, chlorofluorocarbon (CFC)-113, and hydrochlorofluorocarbon (HCFC)-141b when used in adhesives or in aerosol solvents because nPB in these end uses poses unacceptable risks to human health when compared with other substitutes that are available. In addition, EPA takes comment on alternate options that would find nPB acceptable subject to use conditions in adhesives or in aerosol solvents. This action also proposes to list nPB as acceptable, subject to use conditions, as a substitute for methyl chloroform, CFC- 113, and hydrochlorofluorocarbon (HCFC)-141b in the coatings end use. This proposal supersedes EPA's proposal of June 3, 2003 on the acceptability of nPB as a substitute for ozone-depleting substances for aerosols and adhesives.
DATES: Comments must be received in writing by July 30, 2007. Under the Paperwork Reduction Act, comments on the information collection provisions must be received by the Office of Management and Budget (OMB) on or before June 29, 2007. Any person interested in requesting a public hearing, must submit such request on or before June 29, 2007. If a public hearing is requested, a separate notice will be published announcing the date and time of the public hearing and the comment period will be extended until 30 days after the public hearing to allow rebuttal and supplementary information regarding any material presented at the public hearing. Inquiries regarding a public hearing should be directed to the contact person listed below.
ADDRESSES: Submit your comments, identified by Docket ID No. EPA-HQ- OAR-2002-0064, by one of the following methods:
http://www.regulations.gov. Follow the on-line
instructions for submitting comments.
E-mail: A-And-R-Docket@epa.gov.
Mail: Air and Radiation Docket, Environmental Protection Agency, Mailcode 6102T, 1200 Pennsylvania Ave., NW., Washington DC 20460, Attention Docket ID No. EPA-HQ-OAR-2002-0064. In addition, please mail a copy of your comments on the information collection provisions to the Office of Information and Regulatory Affairs, Office of Management and Budget (OMB), Attn: Desk Officer for EPA, 725 17th St., NW., Washington, DC 20503.
Hand Delivery: EPA Docket Center, (EPA/DC) EPA West, Room 3334, 1301 Constitution Ave., NW., Washington, DC, Attention Docket ID No. EPA-HQ-OAR-2002-0064. Such deliveries are only accepted during the Docket's normal hours of operation, and special arrangements should be made for deliveries of boxed information.
Instructions: Direct your comments to Docket ID No. EPA-HQ-OAR- 2002-0064. EPA's policy is that all comments received will be included in the public docket without change and may be made available online at http://www.regulations.gov, including any personal information
provided, unless the comment includes information claimed to be Confidential Business Information (CBI) or other information whose disclosure is restricted by statute. Do not submit information that you consider to be CBI or otherwise protected through http://www.regulations.gov
or e-mail. The http://www.regulations.gov Web site is an ``anonymous
access'' system, which means EPA will not know your identity or contact information unless you provide it in the body of your comment. If you send an e-mail comment directly to EPA without going through http://www.regulations.gov , your e-mail address will be automatically captured
and included as part of the comment that is placed in the public docket and made available on the Internet. If you submit an electronic comment, EPA recommends that you include your name and other contact information in the body of your comment and with any disk or CD-ROM you submit. If EPA cannot read your comment due to technical difficulties and cannot contact you for clarification, EPA may not be able to consider your comment. Electronic files should avoid the use of special characters, any form of encryption, and be free of any defects or viruses. For additional instructions on submitting comments, go to Section I.B. of the SUPPLEMENTARY INFORMATION section of this document.
Docket: All documents in the docket are listed in the http://www.regulations.gov index. Although listed in the index, some
information is not publicly available, i.e., CBI or other information whose disclosure is restricted by statute. Certain other material, such as copyrighted material, is not placed on the Internet and will be publicly available only in hard copy form. Publicly available docket materials are available either electronically in http://www.regulations.gov or in hard copy at the Air and Radiation Docket,
EPA/DC, EPA West, Room 3334, 1301 Constitution Ave., NW., Washington, DC. The Public Reading Room is open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number for the Public Reading Room is (202) 566-1744, and the telephone number for the Air and Radiation Docket is (202) 566-1742.
FOR FURTHER INFORMATION CONTACT: Margaret Sheppard, Stratospheric Protection Division, Office of Atmospheric Programs, Mail Code 6205J, Environmental Protection Agency, 1200 Pennsylvania Ave., NW., Washington, DC 20460; telephone number (202) 343-9163; fax number (202) 343-2362 e-mail address: sheppard.margaret@epa.gov. Notices and rulemakings under the SNAP program are available on EPA's Stratospheric Ozone World Wide Web site at http://www.epa.gov/ozone/snap/regs.
SUPPLEMENTARY INFORMATION:
Table of Contents
-
General Information
-
Does this action apply to me?
-
What should I consider as I prepare my comments for EPA?
-
What acronyms and abbreviations are used in the preamble? II. How does the Significant New Alternatives Policy (SNAP) program work?
-
What are the statutory requirements and authority for the SNAP program?
-
How do the regulations for the SNAP program work?
-
Where can I get additional information about the SNAP program? III. What is EPA proposing today?
-
What is n-propyl bromide?
-
What industrial end uses are included in our proposed decision?
-
What is the proposed text for EPA's listing decisions?
-
What does an unacceptability determination on adhesives and aerosols mean?
-
What is the scope of the proposed determination for coatings?
[[Page 30169]]
-
-
What criteria did EPA consider in preparing this proposal?
-
Availability of Alternatives to Ozone-Depleting Substances
-
Impacts on the Atmosphere and Local Air Quality
-
Ecosystem and Other Environmental Impacts
-
Flammability and Fire Safety
-
Health impacts and exposure V. How did EPA assess impacts on human health?
-
Newly Available Exposure Data
-
Newly Available Data on Health Effects
-
Evaluation of Acceptable Exposure Levels for the Workplace
-
Other Analyses of nPB Toxicity
-
Community Exposure Guideline VI. What listing is EPA proposing for each end use, and why?
-
Aerosol Solvents
-
Adhesives
-
Coatings VII. What other regulatory options did EPA consider?
-
Alternative Option for Comment: Acceptable With Use Conditions Requiring Exposure Limit and Monitoring
-
Regulatory Options Where nPB Would Be Acceptable With Use Conditions Requiring Specific Equipment VIII. What are the anticipated costs of this regulation to the regulated community? IX. How do the decisions for EPA's June 2003 proposal compare to those for this proposal? X. How can I use nPB as safely as possible? XI. Statutory and Executive Order Reviews
-
Executive Order 12866: Regulatory Planning and Review
-
Paperwork Reduction Act
-
Regulatory Flexibility Act
-
Unfunded Mandates Reform Act
-
Executive Order 13132: Federalism
-
Executive Order 13175: Consultation and Coordination With Indian Tribal Governments
-
Executive Order 13045: Protection of Children From Environmental Health and Safety Risks
-
Executive Order 13211: Actions That Significantly Affect Energy Supply, Distribution, or Use
-
-
National Technology Transfer and Advancement Act XII. References
-
General Information
-
Does this action apply to me?
This proposed rule would regulate the use of n-propyl bromide as an aerosol solvent and as a carrier solvent in adhesives and coatings. Businesses in these end uses that currently might be using nPB, or might want to use it in the future, include:
Businesses that manufacture electronics or computer equipment.
Businesses that require a high level of cleanliness in removing oil, grease, or wax, such as for aerospace applications or for manufacture of optical equipment.
Foam fabricators that glue pieces of polyurethane foam together or foam cushion manufacturers that glue fabric around a cushion.
Furniture manufacturers that use adhesive to attach wood parts to floors, tables and counter tops.
A company that manufactures ammunition for the U.S. Department of Defense. Regulated entities may include:
Table 1.--Potentially Regulated Entities, by North American Industrial Classification System (NAICS) Code or Subsector
NAICS code or Category
subsector
Description of regulated entities
Industry......................................
331 Primary Metal Manufacturing. Industry......................................
332 Fabricated Metal Product Manufacturing. Industry/Military.............................
332992 Small Arms Ammunition Manufacturing. Industry......................................
333 Machinery Manufacturing. Industry......................................
334 Computer and Electronic Product Manufacturing. Industry......................................
335 Equipment Appliance, and Component Manufacturing. Industry......................................
336 Transportation Equipment Manufacturing. Industry......................................
337 Furniture and Related Product Manufacturing. Industry......................................
339 Miscellaneous Manufacturing. Industry......................................
326150 Urethane and Other Foam Product (except Polystyrene) Manufacturing.
This table is not intended to be exhaustive, but rather a guide regarding entities likely to be regulated by this action. If you have any questions about whether this action applies to a particular entity, consult the person listed in the preceding section, FOR FURTHER INFORMATION CONTACT.
-
What should I consider as I prepare my comments for EPA?
1. Submitting Confidential Business Information (CBI). Do not submit this information to EPA through http://www.regulations.gov or e-mail.
Clearly mark the part or all of the information that you claim to be CBI. For CBI information in a disk or CD ROM that you mail to EPA, mark the outside of the disk or CD ROM as CBI and then identify electronically within the disk or CD ROM the specific information that is claimed as CBI. In addition to one complete version of the comment that includes information claimed as CBI, a copy of the comment that does not contain the information claimed as CBI must be submitted for inclusion in the public docket. Information so marked will not be disclosed except in accordance with procedures set forth in 40 CFR part 2.
2. Tips for Preparing Your Comments. When submitting comments, remember to:
Identify the rulemaking by docket number and other identifying information (subject heading, Federal Register (FR) date and page number).
Follow directions--The agency may ask you to respond to specific questions or organize comments by referencing a Code of Federal Regulations (CFR) part or section number.
Explain why you agree or disagree; suggest alternatives and substitute language for your requested changes.
Describe any assumptions and provide any technical information and/or data that you used.
If you estimate potential costs or burdens, explain how you arrived at your estimate in sufficient detail to allow for it to be reproduced.
Provide specific examples to illustrate your concerns, and suggest alternatives.
Explain your views as clearly as possible, avoiding the use of profanity or personal threats.
Make sure to submit your comments by the comment period deadline identified.
-
What acronyms and abbreviations are used in the preamble?
Below is a list of acronyms and abbreviations used in this document.
8-hr--eight hour ACGIH--American Conference of Governmental Industrial Hygienists AEL--acceptable exposure limit
[[Page 30170]]
ASTM--American Society for Testing and Materials BMD--benchmark dose BMDL--benchmark dose lowerbound, the lower 95%-confidence level bound on the dose/exposure associated with the benchmark response BSOC--Brominated Solvents Consortium CAA--Clean Air Act CAS Reg. No--Chemical Abstracts Service Registry Identification Number CBI--Confidential Business Information CEG--community exposure guideline CERHR--Center for the Evaluation of Risks to Human Reproduction CFC-113--the ozone-depleting chemical 1,1,2-trifluoro-1,2,2- trichloroethane, C2Cl3F3, CAS Reg. No. 76-13-1 CFC--chlorofluorocarbon cfm--cubic feet per minute CFR--Code of Federal Regulations CNS--central nervous system DNA--deoxyribonucleic acid EDSTAC--The Endocrine Disruptor Screening and Testing Advisory Committee EPA--the United States Environmental Protection Agency FR--Federal Register GWP--global warming potential HCFC-141b--the ozone-depleting chemical 1,1-dichloro-1-fluoroethane, CAS Reg. No. 1717-00-6 HCFC-225ca/cb--the commercial mixture of the two ozone-depleting chemicals 3,3-dichloro-1,1,1,2,2-pentafluoropropane, CAS Reg. No. 422-56-0 and 1,3-dichloro-1,1,2,2,3-pentafluoropropane, CAS Reg. No. 507-55-1 HCFC--hydrochlorofluorocarbon HEC--human equivalent concentration HFC-245fa--the chemical 1,1,3,3,3-pentafluoropropane, CAS Reg. No. 460-73-1 HFC-365mfc--the chemical 1,1,1,3,3-pentafluorobutane, CAS Reg. No. 405-58-6 HFC-4310mee--the chemical 1,1,1,2,3,4,4,5,5,5-decafluoropentane, CAS Reg. No. 138495-42-8 HFC--hydrofluorocarbon HFE--hydrofluoroether HHE--health hazard evaluation ICF--ICF Consulting ICR--Information Collection Request iPB--isopropyl bromide, C3H7Br, CAS Reg. No. 75-26-3, an isomer of n-propyl bromide; also called 2-bromopropane or 2-BP Koc--organic carbon partition coefficient, for determining the tendency of a chemical to bind to organic carbon in soil LC50--the concentration at which 50% of test animals die LOAEL--Lowest Observed Adverse Effect Level Log Kow--logarithm of the octanol-water partition coefficient, for determining the tendency of a chemical to accumulate in lipids or fats instead of remaining dissolved in water mg/l--milligrams per liter MSDS--Material Safety Data Sheet NAICS--North American Industrial Classification System NIOSH--National Institute for Occupational Safety and Health NOAEL--No Observed Adverse Effect Level NOEL--No Observed Effect Level nPB--ln-propyl bromide, C3H7Br, CAS Reg. No. 106-94-5; also called 1-bromopropane or 1-BP NPRM--Notice of Proposed Rulemaking NTP--National Toxicology Program NTTAA--National Technology Transfer and Advancement Act ODP--ozone depletion potential ODS--ozone-depleting substance OEHHA--Office of Environmental Health Hazard Assessment of the California Environmental Protection Agency OMB--U.S. Office of Management and Budget OSHA--the United States Occupational Safety and Health Administration PCBTF--parachlorobenzotrifluoride, CAS Reg. No. 98-56-6 PEL--Permissible Exposure Limit ppm-parts per million RCRA--Resource Conservation and Recovery Act RFA--Regulatory Flexibility Act RfC--reference concentration SIP--state implementation plan SNAP--Significant New Alternatives Policy TCA--the ozone-depleting chemical 1,1,1-trichloroethane, CAS Reg. No. 71-55-6; also called methyl chloroform, MCF, or 1,1,1 TCE--the chemical 1,1,2-trichloroethene, CAS Reg. No. 79-01-6, C2Cl3H; also call trichloroethylene TERA--Toxicological Excellence for Risk Assessment TLV--Threshold Limit Value(tm) TSCA--Toxic Substances Control Act TWA--time-weighted average UMRA--Unfunded Mandates Reform Act U.S.C.--United States Code VMSs--volatile methyl siloxanes VOC--volatile organic compound
-
-
How does the Significant New Alternatives Policy (SNAP) program work?
-
What are the statutory requirements and authority for the SNAP program?
Section 612 of the Clean Air Act (CAA) authorizes EPA to develop a program for evaluating alternatives to ozone-depleting substances, referred to as the Significant New Alternatives Policy (SNAP) program. The major provisions of section 612 are:
Rulemaking--Section 612(c) requires EPA to promulgate rules making it unlawful to replace any class I (chlorofluorocarbon, halon, carbon tetrachloride, methyl chloroform, and hydrobromofluorocarbon) or class II (hydrochlorofluorocarbon) substance with any substitute that the Administrator determines may present adverse effects to human health or the environment where the Administrator has identified an alternative that (1) reduces the overall risk to human health and the environment, and (2) is currently or potentially available.
Listing of Unacceptable/Acceptable Substitutes--Section 612(c) also requires EPA to publish a list of the substitutes unacceptable for specific uses. We must publish a corresponding list of acceptable alternatives for specific uses.
Petition Process--Section 612(d) grants the right to any person to petition EPA to add a substitute to or delete a substitute from the lists published in accordance with section 612(c). EPA has 90 days to grant or deny a petition. Where the Agency grants the petition, we must publish the revised lists within an additional six months.
90-day Notification--Section 612(e) requires EPA to require any person who produces a chemical substitute for a class I substance to notify the Agency not less than 90 days before new or existing chemicals are introduced into interstate commerce for significant new uses as substitutes for a class I substance. The producer must also provide the Agency with the producer's health and safety studies on such substitutes.
Outreach--Section 612(b)(1) states that the Administrator shall seek to maximize the use of federal research facilities and resources to assist users of class I and II substances in identifying and developing alternatives to the use of such substances in key commercial applications.
Clearinghouse--Section 612(b)(4) requires the Agency to set up a public clearinghouse of alternative chemicals, product substitutes, and alternative manufacturing processes that are available for products and manufacturing processes which use class I and II substances.
-
How do the regulations for the SNAP program work?
On March 18, 1994, EPA published the original rulemaking (59 FR 13044) that described the process for administering the SNAP program and issued the first acceptability lists for substitutes in the major industrial use sectors. These sectors include: Refrigeration and air conditioning; foam blowing; solvents cleaning; fire suppression and explosion protection; sterilants; aerosols; adhesives, coatings and inks; and tobacco expansion. These sectors comprise the principal industrial sectors that historically consumed large volumes of ozone- depleting substances.
Anyone who plans to market or produce a substitute for an ozone- depleting substance (ODS) in one of the eight major industrial use sectors must provide the Agency with health and safety studies on the substitute at least 90 days before introducing it into
[[Page 30171]]
interstate commerce for significant new use as an alternative. This requirement applies to the person planning to introduce the substitute into interstate commerce, typically chemical manufacturers, but may also include importers, formulators or end-users when they are responsible for introducing a substitute into commerce.
The Agency has identified four possible decision categories for substitutes: Acceptable; acceptable subject to use conditions; acceptable subject to narrowed use limits; and unacceptable. Use conditions and narrowed use limits are both considered ``use restrictions'' and are explained below. Substitutes that are deemed acceptable with no use restrictions (no use conditions or narrowed use limits) can be used for all applications within the relevant sector end-use. Substitutes that are acceptable subject to use restrictions may be used only in accordance with those restrictions. It is illegal to replace an ODS with a substitute listed as unacceptable.
After reviewing a substitute, the Agency may make a determination that a substitute is acceptable only if certain conditions of use are met to minimize risks to human health and the environment. We describe such substitutes as ``acceptable subject to use conditions.'' If you use these substitutes without meeting the associated use conditions, you use these substitutes in an unacceptable manner and you could be subject to enforcement for violation of section 612 of the Clean Air Act.
For some substitutes, the Agency may permit a narrowed range of use within a sector. For example, we may limit the use of a substitute to certain end-uses or specific applications within an industry sector or may require a user to demonstrate that no other acceptable end uses are available for their specific application. We describe these substitutes as ``acceptable subject to narrowed use limits.'' If you use a substitute that is acceptable subject to narrowed use limits, but use it in applications and end-uses which are not consistent with the narrowed use limit, you are using these substitutes in an unacceptable manner and you could be subject to enforcement for violation of section 612 of the Clean Air Act.
The Agency publishes its SNAP program decisions in the Federal Register. For those substitutes that are deemed acceptable subject to use restrictions (use conditions and/or narrowed use limits), or for substitutes deemed unacceptable, we first publish these decisions as proposals to allow the public opportunity to comment, and we publish final decisions as final rulemakings. In contrast, we publish substitutes that are deemed acceptable with no restrictions in ``notices of acceptability,'' rather than as proposed and final rules. As described in the rule implementing the SNAP program (59 FR 13044), we do not believe that rulemaking procedures are necessary to list alternatives that are acceptable without restrictions because such listings neither impose any sanction nor prevent anyone from using a substitute.
Many SNAP listings include ``comments'' or ``further information.'' These statements provide additional information on substitutes that we determine are unacceptable, acceptable subject to narrowed use limits, or acceptable subject to use conditions. Since this additional information is not part of the regulatory decision, these statements are not binding for use of the substitute under the SNAP program. However, regulatory requirements listed in this column are binding under other programs. The further information does not necessarily include all other legal obligations pertaining to the use of the substitute. However, we encourage users of substitutes to apply all statements in the ``Further Information'' column in their use of these substitutes. In many instances, the information simply refers to sound operating practices that have already been identified in existing industry and/or building-code standards. Thus, many of the comments, if adopted, would not require the affected industry to make significant changes in existing operating practices.
-
Where can I get additional information about the SNAP program?
For copies of the comprehensive SNAP lists of substitutes or additional information on SNAP, look at EPA's Ozone Depletion World Wide Web site at http://www.epa.gov/ozone/snap/lists/index.html. For
more information on the Agency's process for administering the SNAP program or criteria for evaluation of substitutes, refer to the SNAP final rulemaking published in the Federal Register on March 18, 1994 (59 FR 13044), codified at Code of Federal Regulations at 40 CFR part 82, subpart G. You can find a complete chronology of SNAP decisions and the appropriate Federal Register citations at http://www.epa.gov/ozone/snap/chron.html .
-
-
What is EPA proposing today?
In this action, EPA proposes to list n-propyl bromide (nPB) as (1) unacceptable for use as a substitute for CFC-113,\1\ methyl chloroform \2\ and HCFC-141b \3\ in the adhesive and aerosol solvent end uses; and (2) acceptable subject to use conditions (limited to coatings at facilities that, as of May 30, 2007, have provided EPA with information demonstrating their ability to maintain acceptable workplace exposures) as a substitute for methyl chloroform, CFC-113, and HCFC-141b in the coatings end use. This Notice of Proposed Rulemaking (NPRM) supersedes the NPRM published on June 3, 2003 (68 FR 33284) for aerosol solvents and adhesives.
\1\ CFC-113 is also referred to as Freon-113, or 1,1,2- trifluoro-1,2,2-trichloroethane. Its CAS Reg. No. is 76-13-1.
\2\ Methyl chloroform is also referred to as 1,1,1- trichloroethane, TCA, MCF, or 1,1,1. Its CAS Reg. No. is 71-55-6.
\3\ HCFC-141b is also referred to as 1,1-dichloro-1- fluoroethane. Its CAS Reg. No. is 1717-00-6.
-
What is n-propyl bromide?
n-propyl bromide (nPB), also called 1-bromopropane, is a non- flammable organic solvent with a strong odor. Its chemical formula is C3H7Br. Its identification number in Chemical Abstracts Service's registry (CAS Reg. No.) is 106-94-5. nPB is used to remove wax, oil, and grease from electronics, metal, and other materials. It also is used as a carrier solvent in adhesives. Some brand names of products using nPB are: Abzol[supreg], EnSolv[supreg], and Solvon[supreg] cleaners; Pow-R-Wash[supreg] NR Contact Cleaner, Superkleen Flux Remover 2311 and LPS NoFlash NU Electro Contact Cleaner aerosols; and Whisper Spray and Fire Retardant Soft Seam 6460 adhesives.
-
What industrial end uses are included in our proposed decision?
This proposal addresses the use of n-propyl bromide in the aerosol solvent end use of the aerosol sector and the adhesives and coatings end uses in the adhesives, coatings, and inks sector as discussed below. EPA is issuing a decision on the use of nPB in metals, electronics, and precision cleaning in a separate final rule. EPA has insufficient information for ruling on other end uses or sectors where nPB might be used (e.g., inks, foam blowing, fire suppression). 1. Aerosol Solvents
We understand that nPB is being used as an aerosol solvent in:
Lubricants, coatings, or cleaning fluids for electrical or electronic equipment;
Lubricants, coatings, or cleaning fluids for aircraft maintenance; or
[[Page 30172]]
Spinnerrette lubricants and cleaning sprays used in the production of synthetic fibers. 2. Adhesives
Types of adhesives covered under the SNAP program are those that formerly used methyl chloroform, specifically, adhesives for laminates, flexible foam, hardwood floors, tire patches, and metal to rubber adhesives. Of these applications, nPB-based adhesives have been used most widely in spray adhesives used in manufacture of foam cushions, and to a lesser degree in laminate adhesives. 3. Coatings
The SNAP program regulates the use of carrier solvents in durable coatings, including paints, varnishes, and aerospace coatings (59 FR 13118). The SNAP program currently does not regulate carrier solvents in lubricant coatings, such as silicone coatings used on medical equipment (59 FR 13119). Methyl chloroform has been used as a carrier solvent in coatings, and to a much lesser degree, HCFC-141b also has been a carrier solvent. This rule responds to a submission from a facility that is substituting methyl chloroform with nPB as an ammunition coating (sealant).
-
What is the proposed text for EPA's listing decisions?
In the proposed regulatory text at the end of this document, you will find our proposed decisions for those end uses for which we have proposed nPB as unacceptable or acceptable subject to use conditions. The proposed conditions listed in the ``Use Conditions'' column would be enforceable while information contained in the ``Further Information'' column of those tables provides additional recommendations on the safe use of nPB. Our proposed decisions for each end use are summarized below in tables 2 through 4.
Proposed Listings
Table 2.--Aerosols Proposed Unacceptable Substitutes
End Use
Substitute
Decision
Further information
Aerosol solvents.................. n-propyl bromide (nPB) as Unacceptable......... EPA finds unacceptable a substitute for CFC-113,
risks to human health in HCFC-141b, and methyl
this end use compared to chloroform.
other available alternatives. nPB, also known as 1-bromopropane, is Number 106-94-5 in the CAS Registry.
Table 3.--Adhesives, Coatings, and Inks Proposed Unacceptable Substitutes
Enduse
Substitute
Decision
Further information
Adhesives......................... n-propyl bromide (nPB) as Unacceptable......... EPA finds unacceptable a substitute for CFC-113,
risks to human health in HCFC-141b, and methyl
this end use compared to chloroform.
other available alternatives. nPB, also known as 1-bromopropane, is Number 106-94-5 in the CAS Registry.
Table 4.--Adhesives, Coatings, and Inks Substitutes That Are Proposed Acceptable Subject to Use Conditions
End Use
Substitute
Decision
Use conditions
Further information
Coatings............ n-propyl bromide Acceptable subject Use is limited to
EPA recommends the use (nPB) as a
to use conditions. coatings facilities of personal protective substitute for
that, as of May 30, equipment, including methyl chloroform,
2007, have provided chemical goggles, CFC-113, and HCFC-
EPA information
flexible laminate 141b.
demonstrating their protective gloves and ability to maintain chemical-resistant acceptable workplace clothing. exposures.
EPA expects that all users of nPB would comply with any final Permissible Exposure Limit that the Occupational Safety and Health Administration issues in the future under 42 U.S.C. 7610(a). nPB, also known as 1- bromopropane, is Number 106-94-5 in the CAS Registry.
Note: As of May 30, 2007, the Lake City Army Ammunition Plant is the only facility using nPB in coatings that has provided information to EPA that meets this condition.
-
What does an unacceptability determination on adhesives and aerosols mean?
In this action, EPA is proposing to find nPB unacceptable as a substitute for methyl chloroform, CFC-113, and HCFC-141b for use as a carrier solvent in adhesives and as an aerosol solvent. If this proposal were to become final, it would be illegal to use nPB or blends of nPB and other solvents in adhesives or in aerosol solvent formulations as a substitute for ozone-depleting substances.
-
What is the scope of the proposed determination for coatings?
We propose to list nPB as an acceptable substitute, subject to use conditions, for methyl chloroform, CFC-113, and HCFC-141b in coatings for facilities that, as of May 30, 2007, have
[[Page 30173]]
provided EPA information demonstrating their ability to maintain acceptable workplace exposures. EPA has received a petition to allow use of nPB for the ammunition coating application at Lake City Army Ammunition Plant. This is the only coatings application or facility for which EPA has exposure and usage data demonstrating an ability to maintain workplace exposure levels below even the minimum level of the range of exposures that EPA is considering to be potentially acceptable (i.e., 17 to 30 ppm) (see section IV.E for an evaluation of the health risks associated with nPB). If other facilities are interested in using nPB as a substitute for methyl chloroform, CFC-113, or HCFC-141b in their coatings application, or if a person wishes to market nPB for such use, then the interested party would need to make a submission under the SNAP program.
-
-
What criteria did EPA consider in preparing this proposal?
In the original rule implementing the SNAP program (March 18, 1994; 59 FR 13044, at 40 CFR 82.180(a)(7)), the Agency identified the criteria we use in determining whether a substitute is acceptable or unacceptable as a replacement for class I or II compounds:
(i) Atmospheric effects and related health and environmental impacts;
[e.g., ozone depletion potential]
(ii) General population risks from ambient exposure to compounds with direct toxicity and to increased ground-level ozone;
(iii) Ecosystem risks [e.g., bioaccumulation, impacts on surface and groundwater];
(iv) Occupational risks;
(v) Consumer risks;
(vi) Flammability; and
(vii) Cost and availability of the substitute.
In this review, EPA considered all the criteria above. However, n- propyl bromide is used in industrial applications such as electronics cleaning or spray adhesives used in foam fabrication. In those consumer products made using nPB, such as a piece of furniture or a computer, the nPB would have evaporated long before a consumer would purchase the item. Therefore, we believe there is no consumer exposure risk to evaluate in the end uses we evaluated for this rule.
Section 612(c) of the Clean Air Act directs EPA to publish a list of replacement substances (``substitutes'') for class I and class II ozone depleting substances based on whether the Administrator determines they are safe (when compared with other currently or potentially available substitutes) for specific uses or are to be prohibited for specific uses. EPA must compare the risks to human health and the environment of a substitute to the risks associated with other substitutes that are currently or potentially available. In addition, EPA also considers whether the substitute for class I and class II ODSs ``reduces the overall risk to human health and the environment'' compared to the ODSs being replaced. Our evaluation is based on the end use; for example, we compared nPB as a carrier solvent in adhesives to other available or potentially available adhesive alternatives.
Although EPA does not judge the effectiveness of an alternative for purposes of determining whether it is acceptable, we consider effectiveness when determining whether alternatives that pose less risk are available in a particular application within an end use. There are a wide variety of acceptable alternatives listed for aerosol solvents, but not all may be appropriate for a specific application because of differences in materials compatibility, flammability, degree of cleanliness required, local environmental requirements, and other factors.
EPA evaluated each of the criteria separately and then considered overall risk to human health and the environment in comparison to other available or potentially available alternatives. We concluded that overall, environmental risks were not sufficient to find nPB unacceptable in any of the evaluated end uses. However, the overall risks to human health, and particularly the risks to worker health, are sufficiently high in the adhesive and aerosol solvent end uses to warrant our proposal to find nPB unacceptable.
-
Availability of Alternatives to Ozone-Depleting Substances
Other alternatives are available in each end use considered in this proposal. Examples of other available alternatives for aerosol solvents that have already been found acceptable or acceptable subject to use conditions under the SNAP program include water-based formulations, alcohols, ketones, esters, ethers, terpenes, HCFC-141b, HCFC-225ca/cb, hydrofluoroethers (HFEs), hydrofluorocarbon (HFC)-4310mee, HFC-365mfc, HFC-245fa, hydrocarbons, trans-1,2-dichloroethylene, methylene chloride, trichloroethylene \4\ (TCE), perchloroethylene \5\, and parachlorobenzotrifluoride (PCBTF). Of these, hydrocarbons, alcohols, blends of trans-1,2-dichloroethylene and HFEs or HFCs, and HCFC-225ca/ cb are most likely to be used in the same applications as nPB. nPB is already commercially available in aerosols. Its use is primarily for electrical contact cleaning, with some use for benchtop cleaning applications (Williams, 2005).
\4\ Also called trichlorethene or TCE, C2Cl3H, CAS Reg. No. 79-01-6.
\5\ Also called PERC, tetrachloroethylene, or tetrachloroethene, C2Cl4, CAS Reg. No. 127-18-4.
Many alternatives are also available for use in adhesives, coatings, and inks: Water-based formulations, high solid formulations, alcohols, ketones, esters, ethers, terpenes, HFEs, hydrocarbons, trans- 1,2-dichloroethylene, chlorinated solvents, PCBTF, and a number of alternative technologies (e.g., powder, hot melt, thermoplastic plasma spray, radiation-cured, moisture-cured, chemical-cured, and reactive liquid). Of these, the alternative adhesives most likely to be used in the same applications as nPB are water-based formulations, adhesives with methylene chloride, and flammable adhesives with acetone (IRTA, 2000). nPB is already used in adhesives, and particularly in foam fabrication and in constructing seating for aircraft (IRTA, 2000; Seilheimer, 2001).
To our knowledge, nPB is potentially available as a carrier solvent in coatings, but has not yet been commercialized, except for use by one facility, the Lake City Army Ammunition Plant. The Lake City Army Ammunition Plant evaluated twenty-nine carrier solvent alternatives to methyl chloroform and determined that nPB is the only satisfactory alternative for their application given the current process at that facility (Harper, 2005).
-
Impacts on the Atmosphere and Local Air Quality
As discussed in the June, 2003 proposal, nPB emissions from the continental United States are estimated to have an ozone depletion potential (ODP) of approximately 0.013-0.018, (Wuebbles, 2002), lower than that of the ozone depletion potential of the substances that nPB would replace--CFC-113 (ODP = 1.0), and methyl chloroform and HCFC-141b (ODPs = 0.12) (WMO, 2002). Some other acceptable alternatives for these ODSs also have low ODPs. For example, HCFC-225ca/cb has an ODP of 0.02- 0.03 (WMO, 2002) and is acceptable as an aerosol solvent. There are other acceptable solvents for aerosols, adhesives, and coatings that essentially have no ODP--aqueous cleaners, HFEs, HFC-4310mee, HFC- 365mfc, HFC-245fa, hydrocarbons, volatile methyl siloxanes (VMSs), methylene chloride, TCE, perchloroethylene, and PCBTF.
[[Page 30174]]
Based on this information, we do not believe the use of nPB within the U.S., and within the end-uses reviewed in this rulemaking, poses a significantly greater risk to the ozone layer than other available substitutes.
Comments on the June 2003 NPRM expressed concern that other countries, particularly those in equatorial regions, might assume that nPB does not pose a danger to the stratospheric ozone layer if the U.S. EPA's SNAP program finds nPB acceptable (Linnell, 2003; Steminiski, 2003). Because the ODP for nPB is higher when used in the tropics,\6\ we recognize the concerns raised by these commenters. However, EPA is regulating use in the U.S. and cannot dictate actions taken by other countries. We believe the more appropriate forum to address this concern is through the Parties to the Montreal Protocol. At the most recent Meeting of the Parties, the Parties made the following decision with regard to n-propyl bromide, in order to ``allow Parties to consider further steps regarding n-propyl bromide, in the light of available alternatives'' (Decision XVIII/11):
\6\ nPB emissions in the tropics have an ODP of 0.071 to 0.100; the portions of the U.S. outside the continental U.S., such as Alaska, Hawaii, Guam, and the U.S. Virgin Islands, contain less than 1 percent of the U.S.'s businesses in industries that could use nPB. Thus, their potential impact on the ozone layer must be significantly less than that of the already low impact from nPB emissions in the continental U.S. (U.S. Economic Census, 2002a through f).
1. To request the Scientific Assessment Panel to update existing information on the ozone depletion potential of n-propyl bromide, including ozone depleting potential depending on the location of the emissions and the season in the hemisphere at that location;
2. To request the Technology and Economic Assessment Panel to continue its assessment of global emissions of n-propyl bromide, * * * paying particular attention to:
(a) Obtaining more complete data on production and uses of n-propyl bromide as well as emissions of n-propyl bromide from those sources;
(b) Providing further information on the technological and economical availability of alternatives for the different use categories of n-propyl bromide and information on the toxicity of and regulations on the substitutes for n-propyl bromide;
(c) Presenting information on the ozone depletion potential of the substances for which n-propyl bromide is used as a replacement;
3. To request that the Technology and Economic Assessment Panel prepare a report on the assessment referred to in paragraph 1 in time for the twenty-seventh meeting of the Open-ended Working Group for the consideration of the Nineteenth Meeting of the Parties. (MOP 18, 2006)
The global warming potential (GWP) index is a means of quantifying the potential integrated climate forcing of various greenhouse gases relative to carbon dioxide. Earlier data found a direct 100-year integrated GWP (100yr GWP) for nPB of 0.31 (Atmospheric and Environmental Research, Inc., 1995). More recent analysis that considers both the direct and the indirect GWP of nPB found a 100-yr GWP of 1.57 (ICF, 2003a; ICF, 2006a). In either case, the GWP for nPB is comparable to or below that of previously approved substitutes in these end uses.
Use of nPB may be controlled as a volatile organic compound (VOC) under state implementation plans (SIPs) developed to attain the National Ambient Air Quality Standards for ground-level ozone, which is a respiratory irritant. Users located in ozone nonattainment areas may need to consider using a substitute for cleaning that is not a VOC or if they choose to use a substitute that is a VOC, they may need to control emissions in accordance with the SIP. Companies have petitioned EPA, requesting that we exempt nPB from regulation as a VOC. However, unless and until EPA issues a final rulemaking exempting a compound from the definition of VOC and states change their SIPs to exclude such a compound from regulation, that compound is still regulated as a VOC. Other acceptable ODS-substitute solvents that are VOCs for state air quality planning purposes include most oxygenated solvents such as alcohols, ketones, esters, and ethers; hydrocarbons and terpenes; trichloroethylene; trans-1,2-dichloroethylene; monochlorotoluenes; and benzotrifluoride. Some VOC-exempt solvents that are acceptable ODS substitutes include HFC-245fa, HCFC-225ca/cb, HFC-365mfc and HFC- 4310mee for aerosol solvents, and methylene chloride, perchloroethylene, HFE-7100, HFE-7200, PCBTF, acetone, and methyl acetate for aerosol solvents, adhesives, and coatings.
-
Ecosystem and Other Environmental Impacts
EPA considered the possible impacts of nPB if it were to pollute soil or water as a waste and compared these impacts to screening criteria developed by the Endocrine Disruptor Screening and Testing Advisory Committee (EDSTAC, 1998) (see Table 5). Available data on the organic carbon partition coefficient (Koc), the breakdown processes in water and hydrolysis half-life, and the volatilization half-life indicate that nPB is less persistent in the environment than many solvents and would be of low to moderate concern for movement in soil. Based on the LC50, the acute concentration at which 50% of tested animals die, nPB's toxicity to aquatic life is moderate, being less than that for some acceptable cleaners (for example, trichloroethylene, hexane, d-limonene, and possibly some aqueous cleaners) and greater than that for some others (methylene chloride, acetone, isopropyl alcohol, and some other aqueous cleaners). The LC50for nPB is 67 milligrams per liter (mg/l), which is greater and thus less toxic than an LC50of 10 mg/l, one of EPA's criteria for listing under the Toxics Release Inventory (US EPA, 1992; ICF, 2004a). Based on its relatively low bioconcentration factor and log Kowvalue (logarithm of the octanol-water partition coefficient), nPB is not prone to bioaccumulation. Table 5 summarizes information on environmental impacts of nPB; trans-1,2- dichloroethylene, a commonly-used solvent in blends for aerosol solvents, precision cleaning, and electronics cleaning; acetone, a commonly-used carrier solvent in adhesives; trichloroethylene, a solvent used for metals, electronics, and precision cleaning that could potentially be used in aerosol or adhesive end-uses; and methyl chloroform, an ODS that nPB would replace.
[[Page 30175]]
Table 5.--Ecosystem and Other Environmental Properties of nPB and Other Solvents
Description of
Value for trans- Property
environmental Value for nPB 1,2-dichloro- Value for acetone
Value for
Value for methyl property
ethylene
trichloroethylene chloroform
Koc, organic-carbon partition Degree to which a 330 (Source: ICF, 32 to 49 (Source: 5.4 (Source:
106 to 460 (Source: 152 (Source: U.S. coefficient.
substance tends 2004a).
ATSDR, 1996). ATSDR, 1994). ATSDR, 1997).
EPA, 1994a). to stick to soil or move in soil. Lower values (25
hydrolysis not
Hydrolysis half- (Source: ATSDR, weeks\*\ are of
significant
life of 10.7 to 30 2004). concern.).
(Source: ATSDR,
months (Source: 1996).
ATSDR, 1997). Volatilization half-life from Tendency to
3.4 hours-4.4 days 3 to 6.2 hours 7.8 to 18 hours 3.4 hours to 18 days Hours to weeks surface waters.
volatilize and (Source: ICF, (Source: ATSDR, (Source: ATSDR, (Source: ATSDR, (Source: U.S. pass from water 2004a).
1996).
1994).
1997).
EPA, 1994a). into the air. LC50 (96 hours) for fathead Concentration at 67 mg/L (Source: 108 mg/L (Source: 7280 to 8120 mg/L 40.7 to 66.8 mg/L 52.8 to 105 mg/L minnows.
which 50% of
Geiger, 1988). U.S. EPA, 1980). (Source: Fisher (Source: NPS, 1997). (Source: U.S. animals die from
Scientific, 2001).
EPA, 1994a). toxicity after exposure for 4 days. log Kow........................ Logarithm of the 2.10 (Source: ICF, -0.48 (Source: -0.24 (Source: 2.38 (Source:
2.50 (Source: octanol/water 2004a).
LaGrega et al., LaGrega et al., LaGrega et al., LaGrega et al., partition
2001, p. 1119). 2001, p. 1117). 2001, p. 1127). 2001, p. 1127). coefficient, a measure of tendency to accumulate in fat. Log Kow values >3 \;*\ indicate high tendency to accumulate. Bioconcentration factor........ High factors
23 (Source: HSDB, 5 to 23 (Source: 1000)\*\
2004).
ATSDR, 1996). 1994).
ATSDR, 1997).
EPA, 1994a). indicate strong tendency for fish to absorb the chemical from water into body tissues.
\*\Criteria from EDSTAC, 1998.
nPB is not currently regulated as a hazardous air pollutant and is not listed as a hazardous waste under the Resource Conservation and Recovery Act (RCRA). nPB is not required to be reported as part of the Toxic Release Inventory under Title III of the Superfund Amendments and Reauthorization Act. Despite this, large amounts of nPB might be harmful if disposed of in water. We recommend that users dispose of nPB as they would dispose of any spent halogenated solvent (F001 waste under RCRA). Users should not dump nPB into water, and should dispose of it by incineration. We conclude that nPB does not pose a significantly greater risk to the environment than other available alternatives, and that the use of nPB within the U.S. should not be prohibited under the SNAP program on the basis of its environmental impacts.
-
Flammability and Fire Safety
A number of commenters on the June 2003 proposal provided additional information on the flammability of nPB using standard test methods for determining flash point, such as the American Society for Testing and Materials (ASTM) D 92 open cup, ASTM D56 Tag closed cup, and ASTM D93 Pensky-Martens closed cup methods (BSOC, 2000; Miller, 2003; Morford, 2003a, 2003b, and 2003c;
[[Page 30176]]
Shubkin, 2003; Weiss Cohen, 2003). We agree with the commenters that by these standard test methods, nPB displayed no flash point. Thus under standard test conditions, nPB is not flammable, and it should not be flammable under normal use conditions. With its low potential for flammability, nPB is comparable to chlorinated solvents, HCFCs, HFEs, HFC-245fa, HFC-4310mee, and aqueous cleaners, and is less flammable than many acceptable substitutes, such as ketones, alcohols, terpenes, and hydrocarbons. nPB exhibits lower and upper flammability limits of approximately 3% to 8% (BSOC, 2000). A number of other solvents that are typically considered to be non-flammable also have flammability limits (for example, methylene chloride, HCFC-141b, and methyl chloroform). If the concentration of vapor of such a solvent falls between the upper and lower flammability limits, it could catch fire in presence of a flame. Such a situation is unusual, but users should take appropriate precautions in cases where the concentration of vapor could fall between the flammability limits.
-
Health Impacts and Exposure
In evaluating potential human health impacts of nPB used as a substitute for ozone-depleting substances, EPA considered impacts on both exposed workers and on the general population. Using the same approach finalized in the original SNAP rulemaking, EPA evaluated the available toxicity data using EPA guidelines to develop health-based criteria to characterize human health risks (US EPA, 1994b. Inhalation Reference Concentration Guidelines; U.S. EPA, 1991. Guidelines for Developmental Toxicity Risk Assessment; U.S. EPA, 1995a. Benchmark Dose guidelines; U.S. EPA, 1996. Guidelines for Reproductive Toxicity Risk Assessment).
To assess human health risks, EPA followed the four basic steps of risk assessment outlined by the National Academy of Sciences: hazard identification, dose-response relationship, exposure assessment, and risk characterization (NAS, 1983). First, EPA examined available studies on nPB's effects. Second, EPA considered the acceptable exposure levels for evaluating worker exposure and a community exposure guideline (CEG) for evaluating exposure to the general population based upon inhalation exposure. Third, EPA compared the acceptable exposure levels and CEG to available exposure data and projections of exposure levels to assess exposure, including new exposure data available since publication of the June 2003 NPRM. Finally, EPA decided whether there was sufficient evidence indicating that nPB could be used as safely as other alternatives available in a particular end use. Authority To Set an Acceptable Exposure Limit
Two commenters on the June 2003 NPRM said that EPA has no jurisdiction to develop any acceptable exposure limit (AEL) designed to be applicable to a workplace environment and that only the Occupational Safety and Health Administration (OSHA) has that authority (Stelljes, 2003; Morford, 2003d). In contrast, another commenter said that EPA has the authority to set an AEL for nPB under section 612 of the Clean Air Act, has done so in the past for other chemicals (e.g., HFC-4310mee, HCFC-225ca/cb), and should require the AEL as a use condition (Risotto, 2003).
EPA believes it has the authority to calculate exposure limits for the workplace under section 612. Section 612(c) specifically states that
The Administrator shall issue regulations: providing that it shall be unlawful to replace any class I or class II substance with any substitute substance which the Administrator determines may present adverse effects to human health or the environment, where the Administrator has identified an alternative to such replacement that--
(1) reduces the overall risk to human health and the environment; and
(2) is currently or potentially available.
Thus, we must compare the risks to human health and the environment of a substitute to the risks associated with other substitutes that are currently or potentially available, as required by the Clean Air Act. In order to compare risks to human health, EPA performs quantitative risk assessments on different chemicals comparing exposure data and exposure limits, following the process described above by the National Academies of Science (NAS, 1983) and as described in the preamble to the original final SNAP rule (March 18, 1994; 59 FR 13066). Because most humans who are exposed to nPB are exposed in the workplace, the appropriate exposure data and exposure limits to protect human health must include workplace exposure data and acceptable exposure limits for the workplace. Because there is wide disparity in acceptable exposure limits for nPB developed by industry, ranging from 5 ppm to 100 ppm (Albemarle, 2003; Chemtura, 2006; Docket A-2001-07, item II-D-19; Enviro Tech International, 2006; Farr, 2003; Great Lakes Chemical Company, 2001), and because there is not a Permissible Exposure Limit for nPB set by the Occupational Safety and Health Administration, EPA believes it is appropriate to independently evaluate the human health risks associated with use of nPB in the workplace. Similarly, EPA has developed a community exposure guideline to assess the human health effects of nPB exposure to the general public. Skin Notation
Several commenters on the June 2003 proposal stated that a skin notation for nPB is appropriate, while another commenter agreed with EPA's proposal that no skin notation was necessary (Smith, 2003; HESIS, 2003; Werner, 2003, Weiss Cohen, 2003). Rat studies indicate that dermal exposure to nPB results in neither appreciable absorption through the skin (RTI, 2005) nor systemic toxicity (Elf Atochem, 1995). Unlike methyl chloride and dichlorvos, which are absorbed through the skin and could contribute to systemic toxicity (ACGIH, 1991), EPA is not proposing to include a skin notation for nPB in the information provided to users associated with this rulemaking because of the relatively low level of absorption. The American Conference of Governmental Industrial Hygienists (ACGIH) provides no skin notation in its documentation for threshold limit values (TLVs) for several solvents, including nPB (ACGIH, 2005), methylene chloride, and perchloroethylene, and there is no evidence that absorption through the skin is greater for nPB than for the other halogenated compounds. Further, including a statement giving advice about how to reduce skin exposure in the ``Further Information'' column of listings is likely to be more informative to workers than a skin notation.
Given the possibility that some nPB can be absorbed through the skin in humans, and that the solvent can irritate the skin, EPA encourages users to wear protective clothing and flexible laminate gloves when using nPB and encourages vendors to include such precautions in their Material Safety Data Sheets (MSDSs). EPA requests comment on whether it would be useful, in lieu of a skin notation to add the following statement in the ``further information'' column of each end use where we find nPB acceptable with restrictions: ``EPA recommends the use of personal protective equipment, including chemical goggles, flexible laminate protective gloves and chemical-resistant clothing, when using nPB.''
EPA also considered the potential health effects of contamination of nPB formulations with isopropyl bromide
[[Page 30177]]
(iPB).\7\ In the June 2003 proposed rule, we proposed as a use condition that nPB formulations contain no more than 0.05% iPB by weight. One commenter opposed the proposed use condition, stating that it places an undue legal burden on end users, rather than the manufacturers of raw materials, that it would not benefit worker safety, and that the nPB industry has worked to reduce iPB content below 0.05% (Morford, 2003e). We agree that industry has met this contamination limit for several years without regulation. Furthermore, EPA agrees that if users are exposed to nPB concentrations no higher than the highest potentially acceptable concentration (30 ppm), a worker's exposure to iPB will be sufficiently low to avoid adverse effects. Therefore, this proposed rule does not include a use condition limiting iPB content in nPB formulations.
\7\ iPB is also referred to as 2-bromopropane, 2-propyl bromide, or 2-BP. Its CAS registry number is 75-26-3.
1. Workplace Risks
In the June 2003 NPRM, EPA proposed that an exposure limit of 25 ppm would be protective of a range of effects observed in animal and human studies, including reproductive and developmental toxicity, neurotoxicity, and hepatotoxicity. Reduction of sperm motility in rats, noted across multiple studies at relatively low exposures, was determined to be the most sensitive effect. The Agency derived an exposure limit of 18 ppm from a dose response relationship in male rat offspring (``F1 generation'') whose parents were exposed to nPB from prior to mating through birth and weaning of the litters (WIL, 2001). We then proposed to adjust this value upwards to 25 ppm based on principles of risk management, consistent with one of the original ``Guiding Principles'' of the SNAP program (59 FR 13046, March 18, 1994). As we discussed in the June 2003 NPRM, EPA noted that adhesives users should be able to achieve an AEL of 25 ppm and that 25 ppm was between the level based on the most sensitive endpoint (sperm motility in the F1 offspring generation at 18 ppm) and the second most sensitive endpoint (sperm motility in the F0 parental generation at 30 ppm). Following SNAP program principles, we noted that ``a slight adjustment of the AEL may be warranted after applying judgment based on the available data and after considering alternative derivations'' (69 FR 33295). Because the animals were exposed to nPB for some time periods that would not occur during actual occupational exposure, we stated further that ``18 ppm is a reasonable but possibly conservative starting point, and that exposure to 25 ppm would not pose substantially greater risks, while still falling below an upper bound on the occupation[al] exposure limit.''
Since the 2003 proposal, the Agency has reviewed both information available at the time of the 2003 NPRM related to the health risks associated with nPB use, as well as more recent case studies of nPB exposures and effects in the workplace, newly published toxicological studies, comments to the June 2003 NPRM, including new risk assessments on nPB, and a new threshold limit value (TLV) issued by ACGIH.
OSHA has not developed a permissible exposure limit (PEL) for nPB that EPA could use to evaluate toxicity risks from workplace exposure. The ACGIH, an independent organization with expertise in industrial hygiene and toxicology, has developed a final workplace exposure limit of 10 ppm (ACGIH, 2005); however, as discussed below, EPA has concerns about the documentation and basis of ACGIH's derivation.
The Agency reconsidered which exposure levels are likely to protect against various health effects, based on review of all available information. We summarize benchmark dose data for a number of endpoints found in these analyses in Table 6 below. We examined these data to assess the acceptability of nPB use in the aerosol solvent, adhesive and coatings end uses reviewed in this proposed rule. These data indicate that, once uncertainty factors are applied consistent with EPA guidelines, the lowest levels for acceptable exposures would be derived for reproductive effects.\8\ The data indicate that levels sufficient to protect against male reproductive effects (e.g., reduced sperm motility) would be in a range from 18 to 30 ppm,\9\ in the range of 17 to 22 ppm to protect against female reproductive effects (e.g., number and length of estrous cycles), and at approximately 20 ppm for effects related to reproductive success (live litter size).
\8\ By EPA guidelines, we would apply an uncertainty factor of - 10, or approximately 3, for differences between species for all health effects. We would also apply an uncertainty factor of
[radic] 10 (3) for variability within the working population for reproductive and developmental effects, because, among other reasons, these conditions would not necessarily screen out an individual from being able to work, unlike for liver or nervous system effects. Therefore, for reproductive and developmental effects, we use a composite uncertainty factor of 10. See further discussion of uncertainty factors in section V.C. below.
\9\ Based on WIL, 2001, as analyzed in ICF, 2002. The equivalent values based upon Stelljes and Wood's (2004) analysis of WIL, 2001 would be slightly lower, from 16 to 28 ppm.
Table 6.--Summary of Endpoints Using Benchmark Response Modeling
Human Benchmark dose equivalent Endpoint a
Study
lowerbound concentration (BMDL) b (ppm) (HEC) c (ppm)
Liver Effects d
Liver vacuolation in males (F1 offspring WIL, 2001 as analyzed in ICF, 2002
110
116 generation). Liver vacuolation in males (F0 parent WIL, 2001 as analyzed in ICF, 2002
143
150 generation). Liver vacuolation......................... ClinTrials, 1997b as analyzed in
226
170 ICF, 2002 and Stelljes & Wood, 2004.
Reproductive Effects--Male
Sperm motility (F1 offspring generation).. WIL, 2001 as analyzed in ICF, 2002
169
177 WIL, 2001 as analyzed in Stelljes
156
164 & Wood, 2004. Sperm motility (F0 parent generation)..... WIL, 2001 as analyzed in ICF, 2002
282
296 WIL, 2001 as analyzed in Stelljes
263
276 & Wood, 2004. Prostate weight (F0 parent generation).... WIL, 2001 as analyzed in TERA,
190
200 2004.
[[Page 30178]]
Sperm count............................... Ichihara et al., 2000b as analyzed
232
325 in Stelljes & Wood, 2004. Sperm deformities (F0 parent generation).. WIL, 2001 as analyzed in Stelljes
296
311 & Wood, 2004.
Reproductive Effects--Female
Number of estrus cycles during a 3 week WIL, 2001 as analyzed in ICF, 2006
162
170 period (F0 parent generation).
WIL, 2001 as analyzed in ICF, 2006
208
218 Estrous cycle length (F1 offspring
WIL, 2001 as analyzed in TERA,
400
420 generation) d.
2004. Estrous cycle length (F0 parent
WIL, 2001 as analyzed in TERA,
210
220 generation) e.
2004. No estrous cycle incidence (F1 offspring WIL, 2001 as analyzed in TERA,
180
189 generation).
2004. No estrous cycle incidence (F0 parent WIL, 2001 as analyzed in TERA,
480
504 generation).
2004.
Reproductive Effects--Reproductive Success
Decreased live litter size (F1 offspring WIL, 2001 as analyzed in TERA,
190
200 generation).
2004. Decreased live litter size (F2 offspring WIL, 2001 as analyzed in TERA,
170
179 generation).
2004. Pup weight gain, post-natal days 21 to 28 WIL, 2001 as analyzed in TERA,
180
189 (F1 offspring generation).
2004.
Developmental Effects
Fetal body weight......................... WIL, 2001 as analyzed in TERA,
310
326 2004. Fetal body weight......................... WIL, 2001 as analyzed in CERHR,
305
320 2002a.
Nervous System Effects
Hindlimb strength......................... Ichihara et al, 2000a as analyzed
214
300 in Stelljes and Wood, 2004.
a Unless explicitly stated, data are from a parental generation. Of the studies analyzed, only the WIL, 2001 study has multiple generations to be analyzed. b The benchmark response value represents a specified level of excess risk above a control response. c When considering workplace exposures, the human equivalent concentration is the BMDL, adjusted to apply to a 40-hour work week in which workers are exposed for 8 hours a day for five days per week. Animals in the WIL, 2001 study were exposed for 6 hours a day, 7 days a week. Animals in the Ichihara, 2000a and 2000b studies were exposed for 8 hours a day, 7 days a week. Animals in the ClinTrials, 1997b study were exposed for 6 hours a day, 5 days a week. d After applying an uncertainty factor of 3 for animal to human extrapolation, acceptable levels of exposure to protect against liver effects would be in the range of 39 to 57 ppm. e Omits data from those animals that have stopped estrous cycling altogether (TERA, 2004).
2. General Population Risks
EPA used a community exposure guideline of 1 ppm to assess potential risks to the general population living near a facility using nPB (see section V.E below). Of the end uses covered in this rule, use of nPB-based adhesives would result in the highest exposure levels, and so, we first examined general population exposure from adhesives. ICF Consulting modeled inhalation exposure to nPB to people living near a plant using nPB-based adhesives in several scenarios using the Agency's SCREEN3 model (US EPA, 1995b). Based on this modeling, EPA found that the exposure to individuals in the general population was below the community exposure guideline. The analysis indicates that nPB is no greater a hazard to the general population than other acceptable solvents under the SNAP program. For further discussion, see the risk screen for nPB (ICF, 2006a).
Representatives from a state environmental agency and from a potential user of nPB have asked EPA whether we had developed a reference concentration (RfC). We clarify that the community exposure guideline is a value developed by the SNAP program for our risk assessment of nPB following EPA's RfC Guidelines. However, it is not a formal RfC developed by EPA's National Center for Environmental Assessment and is not in IRIS. At this time, EPA does not have plans to issue an official RfC for nPB.
-
-
How did EPA assess impacts on human health?
-
Newly Available Exposure Data
Since publication of the June 2003 NPRM, EPA has received additional information on exposure levels in each end use discussed in this proposal.
In the adhesives end use, we considered new exposure modeling based on information from site visits to facilities using spray adhesives (ICF, 2006a). These data predicted that:
At average rates of ventilation and adhesive application, average workplace exposures would be approximately 60 ppm.
Average adhesive application rates and poor ventilation rates resulted in average exposures of approximately 250 ppm.
High (90th percentile) adhesive application rates and average ventilation rates resulted in average exposures of approximately 600 ppm.
In the worst case scenario with high adhesive application rates and poor ventilation, average workplace exposures would be as high as 2530 ppm.
We compared the modeled data in the four exposure scenarios to measured exposure data in three health hazard evaluations by the National Institute for Occupational Safety and Health (NIOSH) (NIOSH 2002a, 2002b, 2003a).
[[Page 30179]]
Our understanding is that North Carolina OSHA received complaints from workers and requested that NIOSH evaluate health hazards at these three facilities. NIOSH found average exposure levels of 68 ppm, 116 ppm, 127 ppm, and 195 ppm for sprayers actively using the adhesive prior to installation of state-of-the-art ventilation systems (NIOSH 2002a, 2002b, 2003a). The plant with an average exposure level of 68 ppm for sprayers (9 samples) had an average exposure level comparable to the average concentration of 60 ppm in the modeling scenario with average adhesive rates and average ventilation levels. The other plants with average exposure levels of 116 to 127 ppm (20 samples), and of 195 ppm (36 samples) for sprayers had exposure levels between the average modeled exposure for a facility with average adhesive application rates and average ventilation (60 ppm) and the average modeled exposure for a facility with average adhesive application rates and poor ventilation (250 ppm). Based on this comparison, EPA believes the modeled exposure levels are a reasonable predictor of actual exposure based on current industry practice in the adhesive end use.
In the aerosol solvent end use, we received a study on workplace exposure levels of nPB-based aerosols from a commenter (Linnell, 2003). This study was performed to simulate typical exposure levels in a number of situations where nPB might be used in the workplace while using different types of ventilation equipment, rather than using data from current industry users of nPB-based aerosols in their actual manufacturing or maintenance processes. As discussed below in section VI.A., we are concerned that the exposure data and ventilation levels in this study may not be representative of use of nPB-based aerosols in industry. Personal breathing zone samples taken from the collars of workers showed 8-hour time-weighted average (TWA) exposures of 5.5, 13, and 32 ppm for workers using 310 g of nPB from a spray can \10\ (Linnell, 2003). The two higher exposure levels occurred in the absence of any local or regional ventilation; the use of both local and regional ventilation equipment with ventilation levels around 1900 ft3/min was associated with the lowest exposure level. Short-term exposures of 370, 1,100 and 2,100 ppm taken from a room with regional ventilation at 640 cubic feet per minute (cfm), when averaged over an 8-hour period, resulted in exposures of 12, 34, and 66 ppm (Linnell, 2003). EPA considers the highest of these 8-hour values, 66 ppm, not to be representative of worker exposure from inhalation because the measurement was taken from the worker's wrist, rather than from his breathing zone. Another short-term exposure value of 190 ppm, taken from a vented booth with local ventilation at 472 cfm, in addition to the regional ventilation of 640 cfm, resulted in an 8-hour exposure of 6 ppm. Similar measurements were made in another study we considered in developing the June 2003 NPRM: Eight hour (8-hr) TWA exposures of 11.3, 15.1, 17.0, and 30.2 ppm with regional ventilation of 300 cubic feet per minute from a fan for the entire room (Confidential submission, 1998).
\10\ Unlike samples measured directly in the breathing zone, area samples measured in the study are not considered representative of actual exposure and are not discussed here. Short-term measurements taken over 15 minutes from personal samplers, although in some cases extremely high, are not discussed in detail here because available toxicity information does not indicate need for a short-term exposure limit for nPB in addition to the 8-hr TWA limit (ACGIH, 2005; ERG, 2004). Additional information on these other samples is in the occupational exposure assessment for aerosols in the risk screen for nPB (ICF, 2006a).
Another commenter submitted information on aerosol exposures for a number of other available alternative aerosols (Werner, 2003). While these data do not include nPB, based on the properties of aerosol solvents, we believe it is reasonable to compare concentrations of these different chemicals to potential nPB exposures. The study compared concentrations of eight different chemicals that are acceptable under the SNAP program in aerosol formulations: HFE-7100, HFE-7200, trans-1,2-dichloroethylene, HCFC-225ca and -225cb, acetone, pentane, and HFC-134a. In this study, with ventilation of only 48 cfm, 8-hr TWA exposure from the different chemicals varied from 35.5 ppm to 194.0 ppm,\11\ below the recommended exposure levels for these particular chemicals (ICF, 2006a) but above the range of exposure levels that EPA would consider acceptable for nPB.
\11\ These measurements can be converted to estimates of nPB exposure by multiplying the measured concentration of the alternate chemical by the molecular weight of the same alternate chemical and dividing this by the molecular weight of nPB, 123. After performing this calculation, the equivalent exposure levels for nPB vary from 29.5 ppm to 394.4 ppm.
In addition, we considered new information from modeling of nPB exposures (ICF, 2006a). The modeling examined exposure levels that would be expected at ventilation levels of 450 cfm, 625 cfm, and 1350 ppm, considering the molecular weight of the compound and the composition of different aerosol blends. EPA's SNAP program has previously used these same levels to calculate potential aerosol exposures, based upon exposure levels expected during benchtop cleaning. In a space with an air exchange rate of 450 ft3/ minute or less,\12\ EPA's modeling predicts 8-hour average exposure of approximately 16 to 17 ppm if a user sprays 450 g of nPB (approximately 1 lb),\13\ and corresponding higher exposure values at higher spray rates (e.g., 33 ppm if the amount of nPB sprayed is 900 g) (ICF, 2006a). Exposure values were predicted to be lower at higher ventilation rates.
\12\ This corresponds roughly to a regional or room fan at low levels or natural air currents in an open area. Confined areas would have even lower air exchange rates with higher exposure levels.
\13\ We consider use of 1000 g/day to be the high end of typical use, based on the setup of one of the exposure studies (Confidential Submission, 1998). The typical aerosol solvent user in the electronics industry uses a can per day (Williams, 2005). This is comparable to or slightly less than the spray rate assumed in the modeling.
Since the June 2003 NPRM, EPA received a new submission for nPB in coatings (Lake City Army Ammunition Plant, 2003). The Lake City Army Ammunition Plant provided data on workplace exposure to nPB (Lake City Army Ammunition Plant, 2004). The mean exposure at this facility was 3.7 ppm. Out of 31 samples taken, 25 (approximately 80%) were below 5 ppm. Only one of 31 samples had an exposure level above 10 ppm, and that exposure value was approximately 21 ppm.
-
Newly Available Data on Health Effects
Since publication of the June 2003 NPRM, EPA has examined additional occupational (Table 7) and animal (Table 8) studies that have become available:
[[Page 30180]]
Table 7.--Recent Studies on nPB Occupational Exposure
Sample size/ Case Study
population Exposure data
Observations
Remarks
Beck and Caravati, 2003....... 6 foam cushion Exposure during Lower leg weakness Small sample size factory workers 30-40 hr/wk for accompanied by pain studied. Possible (gluers).
a 3-month
and difficulty with interference or period.
standing and
synergistic effects Exposure
walking, numbness of from other adhesive measured in one legs and feet,
ingredients (1,2- day was a mean hyperreflexia and epoxybutane and of 130 ppm
hypertonicity of styrene-butadiene). (range, 91-176 lower extremities, ppm).
dizziness and shortness of breath, and peripheral neurotoxicity. Measured serum bromide levels were elevated, range 44- 170 mg/dL. Majersik et al., 2004;
6 foam cushion 5-8 hr/day for Subacute onset of Follow-up to Beck and Majersik et al., 2005 *.
factory workers at least 2
lower extremity
Caravati (2003). (gluers).
years with mean pain, difficulty Chronic nPB exposure air
walking, and high associated with concentration serum bromide levels incapacitating of 130 ppm on in blood. Neurotoxic neurotoxic syndrome. last day of symptoms persisted Initial report from study.
for at least 2 years Utah OSHA indicated Measurements after exposure ended. erroneously that taken over 9
workers were not hours
spraying while (equivalent to
measurements were 92-127 ppm with
taken. In fact, mean of 108 ppm
adhesives were being for an 8-hour
sprayed and fans TWA).
were being used only for portions of the day that measurements were taken, making measurements likely to be representative of conditions during the past several months at the plant. Ichihara et al., 2004a........ 37 chemical 12 hour shifts Mucosal irritation Inadequate exposure plant workers over 2-day
(nose, throat),
characterization and (24 males and period, mean headache, dizziness, exposure to other 13 females). concentration constipation,
potential toxicants, of 82 ppm
intoxication, and small sample size, (range, 0-170 feeling light-headed and no appropriate ppm).
or heavy-headed. control group. Four female workers Healthy worker complained of
effect possible, disruption or
where more sensitive cessation of
workers left the menstruation. No factory between 1996 severe chronic
and 1999. symptoms of neurological damage at less than 170 ppm. Several workers had hemoglobin and hematocrit values outside of the normal range and were diagnosed with mild anemia; most of these cases also showed signs of iron deficiency. Ichihara et al., 2004b........ 27 female
1-day exposure Responses indicated No long-term exposure chemical plant period, range anxiety, fatigue, measurements, small workers (23 age of exposure, confusion, tension, sample size; lack of matched with 23 0.34-49 ppm. and depression.
controls for age, females from a
Changes in menstrual height, and body- beer factory
status but not
weight. Low B control group).
statistically
vitamin levels in significant. Effects normal range in some on peripheral and workers but central nervous
researchers system--diminished concluded this did vibration sensation not cause observed of the foot;
neurological significantly longer effects. distal latency in Additionally, the the tibial nerve; study did not decreased values in indicate any sensory nerve
significant conduction velocity differences in the in the sural nerve; prevalence of and lower scores on menstrual cycle memory and
abnormalities. perceptual tests. No comparable effects seen in control group. Nemhauser, 2005 *............. Foam cushion In 1999 study, Higher exposure to Small sample sizes factory workers 16 workers
nPB and dose-
studied with (gluers) in exposed to mean dependent
moderate worker North Carolina. air
relationship among participation. concentration those who reported Healthy worker of 116 ppm, and anxiety, headache, effect likely 12 sprayers and ataxia. No
occurred: Those that exposed to mean reproductive
had most significant concentration abnormalities
health effects had of 108 ppm with reported in medical already removed range of 58 to survey for men or themselves from 254 ppm. In women. Semen
workplace by the 2001 study, 13 analysis found no time of the study. workers exposed differences between No arsenic found at to nPB mean air exposed and
the plant. concentration unexposed workers. Neurotoxic effects of 46 ppm and
caused by nPB. See 12 sprayers
related Health were exposed to
Hazard Evaluation mean
(HHE): NIOSH, 2003a. concentration of 101 ppm, with range of 38 to 281 ppm. NIOSH, 2003a.................. 16 workers in 1999 Initial Most workers exposed Arsenic was not 1999
Site Visit: to nPB levels > 25 attributed to evaluation; 13 Geometric mean ppm. Exposure
occupational workers in 2001 nPB
concentrations lower exposure. The follow-up
concentration in 2001 than 1999, National Institute evaluation. (from personal but difference not for Occupational samples), 81.2 statistically
Safety and Health (range, 18-254 significant.
(NIOSH) stated that ppm); 2001
Headache, anxiety, neurological follow-up:
feeling drunk
symptoms may have Geometric mean, associated with nPB been related to 81.2 ppm
exposure.
excess exposure to (range, 7-281 Hematological
nPB, but that no ppm).
endpoints unaffected other effects could in exposed group. No conclusively be correlation of nPB related to nPB exposure with sperm exposure. or semen indices or with neurological abnormalities.
[[Page 30181]]
Raymond and Ford, 2005 *...... 4 foam cushion Exposure study Dizziness, numbness, Small sample size, factory workers conducted 9 ocular symptoms, possible confounding (gluers) in months after lower extremity
effect from arsenic. North Carolina. index patient weakness and became ill
unsteady gait, indicated
weakness, workers exposed hypesthesia, and to mean nPB air ataxic gait in all concentration four workers. of 116 ppm. 4 Symptoms decreased workers exposed over time but after for 2-3 weeks six years, at least before initial one worker re- symptoms
exposed twice at detected.
other furniture plants; one or more still suffer from ataxia. Toraason et al., 2006......... 41 and 22 foam 1-3 days up to 8 No statistically Authors find limited cushion factory hrs per day, significant
evidence that nPB workers
with
differences in DNA poses a ``small (gluers) at 2 concentrations damage with worker's risk'' for DNA facilities. of 0.2-271 ppm nPB exposure. In damage. at facility A, vitro results showed 4-27 ppm at nPB increased DNA facility B. damage.
* Presentation at North American Congress of Clinical Toxicology on September 14, 2005.
Table 8.--Recent Animal Studies of nPB Effects
Population/sample Citation
size
Exposure
Observations
Comments
Fueta et al., 2002................ 24 male Wistar rats 6 hr/day, 5 day/wk No apparent morphological defects Only one exposure concentration was (12 control, 12 for 8 weeks at 700 in the brain.
used (which is higher than the exposed).
ppm.
level already associated with other toxic effects in rodents [400 ppm]) and a shorter exposure duration (8 weeks) was used than the other subchronic studies that have shown effects (13 weeks). Fueta et al., 2004................ 58 male Wistar rats 6 hr/day, 5 day/wk No apparent morphological defects Unclear how nPB and/or its (29 experimental for 4 to 8 weeks, in the brain. Chronic inhalation metabolites directly act on and 29 in control 700 ppm.
changes brain enzyme levels and receptors or channels in the group).
electrical activity that is
brain. reversible after exposure. Furuhashi et al., 2006............ 80 Wistar rats (pups (1) 8 hr/day (4 hr, (1) At 800 ppm: most rat offspring Authors concluded that exposure to and their dams). followed by 2.5-hr died within 2 days of birth or in nPB during pregnancy and lactation rest period,
utero;. body weights of dams
adversely affects growth and followed by 4 hr significantly lower, organ weights survival of offspring. Low numbers exposure), 7 day/wk of offspring significantly lower of offspring in 400- and 800-ppm during gestation after weaning at 800 ppm in males, exposure groups prevent and nursing at 0, and 800 and 400 ppm in females. statistical testing 100, 400, 800 ppm Most sperm and estrous indicators EPA comments: Study design in first experiment. did not differ among the groups, inconsistent with guidelines for (2) Dams exposed although the rate of sperm arrival developmental studies, so (800 ppm) during to the cauda epididymis was
comparisons to previous studies gestation (Group significantly lower in the 400 ppm are difficult. The mechanism for A), offspring not group. Inconsistent or no changes the adverse effects observed is exposed during
in biochemical indicators.
not known (e.g., indirect exposure nursing. Offspring (2) Second experiment No difference through milk, changes in nursing of Group (B) of in body weights and pregnancy
behavior, changes in milk unexposed dams were endpoints between exposed (800 production, exposure in utero, nursed by exposed ppm) and unexposed dams. Live
changes in the intrauterine dams. Offspring in offspring at birth, survival
environment) control groups C rates, body weights, significantly and D not exposed. decreased, number of dead offspring, significantly increased in 800-ppm groups. Honma et al., 2003................ Fisher 344 male rats 8 hr/day, 7day/wk 3 week exposure to greater than 50 Neurological effects shown to be for three weeks ppm temporarily increased
transient and reversible at >= 200 exposed to 0, 10, locomotor activity and ambulatory ppm (Ichihara et al., 2000) or 50, 200 or 1000 ppm and rearing behaviors in male rats. absent after 28 days of exposure (5 rats/dosage and
at concentrations >= 400 ppm 5 different tests).
(ClinTrials, 1997a) or after 90 days of exposure at concentrations up to 600 ppm (ClinTrials, 1997b) in other studies. Human studies are limited by co-exposures and poor estimates of exposure concentrations. Thus, EPA is not using this endpoint as the basis of an AEL.
[[Page 30182]]
Ishidao et al., 2002.............. 30 male Wistar rats. 6 hr/day, 5 day/wk nPB is metabolized rapidly in the Exposure levels are higher than in with test groups rat following exposures to nPB at some other studies and are much (10/dose) exposed concentrations >= 700 ppm for at higher than concentrations seen in to 700 ppm for 4 least 3 weeks.
the workplace. nPB metabolism and 12 weeks and
appears to be different following 1500 ppm for 3 and
multiple exposures as compared to 4 weeks.
acute exposures (see RTI, 2005; ICF, 2006b). NTP, 2003......................... Female and male 0, 62.5, 125, 250, Early mortality in mice at 500 ppm Unpublished study. Conclusions B6C3F1 mice and 500 (rats and
accompanied by liver and lung cell drawn from a review of raw data Fischer 344 rats. mice), 1000 (rats) degeneration and cytoplasmic
from the National Toxicology ppm for 90 days. vacuolization. Cytoplasmic
Program (NTP) Web site. In vacuolization also in rat liver general, the severity of effects cells >= 250 ppm (males) and >= (in non-reproductive organs) is 500 ppm (females), with increased slightly higher at lower severity at higher doses. No
concentrations in male rats than adverse central nervous system in females. (CNS) effects or histopathology reported. RTI, 2005/Garner et al., 2006..... Female and male Exposure via several nPB cleared by mice after 48 hours The study authors concluded that: B6C3F1mice and
injection routes as follows: 45% as volatiles in nPB administered via Fisher 344N rats, (intraperitoneal, the breath, 28% as CO2 in the
intraperitoneal injection or four to six animals intravenous,
breath, 26% in urine, Metabolism of nPB appears conducted via bolus urine and volatiles in breath were to be primarily through cytochrome dosing at 5, 20, or higher in mice. At higher doses, P450 enzymes (CYP2E1), 100 mg/kg body
the amount of nPB excreted in
particularly in mice; glutathione weight. Inhalation urine and as CO2 decreased, with a conjugation still plays an concentrations of much greater change in rats
important role in rats. 70, 240, 800, and compared to mice.
At high concentrations, 2700 ppm
After pretreatment with a female rats may have a decreased administered in a cytochrome P450 inhibitor, a
capacity to metabolize nPB single acute
decrease in nPB cleared as CO2 compared to male rats. exposure. A dose of (80%) and urine (40%);
nPB decreases glutathione 96 mg/kg was
pretreatment with a glutathione levels in the liver after a one- applied to a shaved inhibitor reduced nPB cleared as time exposure to nPB at area on the backs CO2 by 10% and urine by 4%.
concentrations as low as 70 ppm. of six male rats The Vmax, a measure of the nPB is not appreciably with a non-
maximum initial rate of an enzyme- absorbed (~3-27%) in rats occlusive charcoal catalysed reaction, is 0.227 for following dermal application. filter covering male rats, 0.143 for female rats, EPA agrees with these points, (that is, one that 0.329 for male mice and 0.234 for except we found that gender does not prevent female mice. Half-lives were
differences were only apparent in evaporation).
comparable between males and
rats at very high concentrations females at For rats exposed to nPB note that: through skin, 37% of the dose was Inhalation tests were only excreted in volatiles, 1.2 % in one-time exposures at very high urine, 1.7% as CO2, and 35.7% was concentrations (240 to 2700 ppm), on the applicators or in the skin and thus, are not comparable to washes. Only 0.32% remained in long-term dosing at the lower tissues. Airborne concentrations levels expected in the workplace. of nPB in the chamber were 4 to 10 Results of dermal testing ppm after dosing.
are not conclusive because of potential for inhalation exposure. Sohn et al., 2002................. 40 male and 40
6 hr/day, 5 day/wk No effects on mortality, activity, The differences between the various female Sprague- for 13 weeks, test weight gain, food consumption, studies may be due to variability Dawley rats.
groups (10/sex/ urinalysis, or histological
in exposure methodology and dose) were exposed effects in the brains and spinal achieved concentrations of nPB. to 0, 200, 500 or cords. 1250 ppm. Stump, 2005*...................... 125 female/125 male Both test groups of Decreased litter size at 250 and Reproductive effects seen in both rats in first
25 male rats/ 25 500 ppm in both generations.
rat sexes which is a strong signal generation and 100 female rats exposed Decreased fertility at 100 and 250 of reproductive toxicity potential female/100 male to 0, 100, 200, ppm in offspring generation.
in humans. The author considers rats in offspring 250, 500 and 750 Complete infertility at 750 ppm.... 100 ppm to be a lowest observed generation.
ppm nPB for 10
adverse effect level (LOAEL). This weeks.
is a presentation of data from WIL, 2001. Wang et al., 2003................. 36 male Wistar rats. 8 hr/day, 5 day/wk Decrease in creatine kinase in the Small study size. No behavioral for 12 weeks, test spinal cord (17% at >= 200 ppm) changes or physical symptoms were groups ( 9 rats) and brain (15-28% at >= 400 ppm) observed in the animals, so the were exposed to 0, at 200, 400, and 800 ppm. No
toxicological relevance of the 200, 400 or 800 ppm. physical or behavioral changes decrease in creatine kinase is observed.
questionable. Yamada et al., 2003............... 40 female Wistar 8 hr/day, 7 day/wk All rats at 800 ppm became
Data suggest that nPB is affecting rats.
with test groups (9/ seriously ill after 7 weeks of the maturation of ovarian dose) exposed to 0, exposure. Significant decrease in follicles. A no observed adverse 200, 400, or 800 antral follicles at >= 200 ppm, effect level (NOAEL) of 200 ppm is ppm for 12 weeks. and a decrease in the number of identified with a LOAEL of 400 ppm female rats exhibiting regular for the changes in estrus cycles. estrous cycles in 400-ppm females during 7-9 weeks of exposure and at 2-3 weeks at the 800-ppm dose.
* Presentation at North American Congress of Clinical Toxicology on September 14, 2005
[[Page 30183]]
In general, the recent animal studies collectively show a range of effects associated with nPB exposure that are qualitatively consistent with previously published findings. (Exceptions to this are the negative results regarding central nervous system toxicity in the NTP (2003) study and the Sohn (2002) study on rats.) Some general conclusions we draw from the new studies include:
Case reports of nPB exposure in the workplace indicate that severe, possibly irreversible, neurological effects may occur at sustained concentrations of approximately 100 ppm or greater (Beck and Caravati, 2003; Majersik et al, 2004; Majersik et al., 2005; Ichihara et al., 2002a; Miller, 2005; Raymond and Ford, 2005). In other cases, similar or higher concentrations up to 170 ppm caused less severe nervous system effects (Nemhauser, 2005; NIOSH, 2003a; Ichihara, 2004a). Some neurological effects occurred in workers at levels of less than 50 ppm (Ichihara et al., 2004b). Because of design and methodological limitations, such as small numbers of subjects and limited exposure information, these studies do not provide a sufficient quantitative basis to derive an acceptable exposure limit.
Data on female rats indicate that nPB affects the maturation of ovarian follicles and the ovarian cycle (Yamada et al., 2003), consistent with previously reviewed data (WIL , 2001; Sekiguchi et al., 2002).
Some data on occupation exposure suggest that workers exposed to nPB may have experienced menstrual disorders (Ichihara et al., 2002; Ichihara et al., 2004b). However, the data are not statistically significant and are not sufficient to conclude that nPB exposure caused these female reproductive effects.
Data on DNA damage in workers exposed to nPB was not statistically significant (Toraason et al., 2006).
Metabolic data on mice and rats indicate some species differences. Metabolism of nPB appears to be primarily through cytochrome P450 enzymes, particularly in mice; glutathione conjugation also plays a role, and a bigger role for rats than for mice (RTI, 2005).
New data from toxicological studies on nervous system effects remain inconsistent and equivocal concerning the level at which nervous system effects occur (Fueta et al., 2002; Fueta et al., 2004; Honma et al., 2003; Ishidao et al., 2002, NTP, 2003; Sohn et al. 2002, Wang et al., 2003).
A number of commenters on the June 2003 NPRM suggested that EPA should consider neurotoxicity as the endpoint in deriving an AEL for nPB (Linnell, 2003; Werner, 2003; Rusch and Bernhardt, 2003, Rusch, 2003). In particular, they requested that EPA consider the study conducted by Wang (2003) and epidemiological data on neurotoxic effects of nPB. As discussed above, the data on neurotoxic effects of nPB on workers are limited and are not sufficient to determine acceptable levels of exposure. In the study on rats by Wang et. al. (2003), measurements found a decrease in enzymes in the spinal cord and brain at 200, 400, and 800 ppm, but the animals displayed no physical or behavioral changes. Because of the lack of physical symptoms or behavioral changes, EPA does not believe that the decrease in enzyme levels in the central nervous system are toxicologically relevant. Other studies examining neurological effects of nPB showed those effects to be transient and reversible at and above 200 ppm (Ichihara et al., 2000a). Exposures of 200 ppm and above for three weeks had no effect on memory, learning function, or coordination of limbs (Honma, 2003); the effect of spontaneous locomotor activity seen in this study at 50 ppm and above was not considered adverse by the authors. In other studies, neurological effects were absent after extended periods of exposure-after 28 days of exposure at concentrations > 400 ppm (ClinTrials, 1997a) and after 90 days of exposure at concentrations up to 600 ppm (ClinTrials, 1997b). Thus, although neurological effects have been associated with nPB exposure, the data are currently insufficient to quantify and determine acceptable exposure levels based on this endpoint.
One commenter on the June 2003 NPRM requested that EPA evaluate a study by Yamada et al. (2003), a study published just prior to the June 2003 NPRM. In response to the comment, EPA reexamined Yamada et al., 2003 and re-evaluated the literature (Ichihara et al., 1999, 2002, 2004a,b; Sekiguchi, 2002, Yamada et al., 2003; WIL, 2001) to assess potential reproductive toxicity in females (ICF, 2006a, Att. A). A peer review of these effects is in the public docket (ICF, 2004b). Multiple benchmark analyses found a statistically significant decrease in the number of estrous cycles and increase in estrous cycle length associated with nPB exposure, consistent with other reproductive endpoints, namely reductions in sperm motility, decreased live litter size, and change in prostate weight (ICF, 2002a; ICF, 2006a; Stelljes and Wood, 2004; TERA, 2004).
Reproductive effects are seen in males, females, and offspring, and in different generations of the two-generation study (WIL, 2000). They also are consistent with results seen in one-generation reproductive studies, such as Ichihara et al. (2000b) and Yamada (2003). See Table 6 above in section IV.E.1. for a more complete list of the different health effects. EPA believes that the preponderance of the data indicate that exposure levels sufficient to protect against male reproductive effects (e.g., reduced sperm motility) would be in a range from 18 to 30 ppm, in the range of 17 to 22 ppm to protect against female reproductive effects (e.g., number and length of estrous cycles), and at approximately 20 ppm for effects related to reproductive success (live litter size). We have not determined what specific level within those ranges (an overall range of 17 to 30 ppm) is most appropriate for evaluating whether a substitute may be used safely and consider these exposure levels to be potentially acceptable. Therefore, we assessed the acceptability of nPB by considering whether it could be used safely in the three end-uses. For end-uses with likelihood of exposures above the range we are considering, while following typical industry practices, we are proposing an unacceptability determination. For end-uses that as their normal practice meet exposure levels below the range we are considering, we are proposing an acceptability determination. It is not necessary for 100% of exposure data for an end use to be above or below the range of 17 to 30 ppm in order to make a determination on the acceptability of an end use because there may be occasional cases that are not following common industry practices. Unusual events would not indicate the industry's likelihood of keeping exposures at safe levels, and thus, should not be the determining factor in our decision. Rather, we consider the overall likelihood that typical industry use would consistently result in acceptably low or unacceptably high exposures.
In the June 2003 NPRM, EPA used a BMDL of 169 ppm as a point of departure for developing an AEL. Some commenters stated that data from the F1 generation is inappropriate for calculating occupational exposure, citing statements from toxicologists, such as, ``occupational exposure involves adults only.'' They also stated that EPA has not required this for other chemicals and that the resulting value is more conservative than what is normal and appropriate for industrial toxicology (Morford, 2003f, Ruckriegel, 2003). Others stated that sperm motility effects on the F1 generation are appropriate to consider (Risotto, 2003; Farr, 2003), particularly because of the
[[Page 30184]]
potential for in utero effects and because of the consistent presence of these reproductive effects in both generations and at multiple levels. EPA acknowledges that using data from the F1 offspring generation may be conservative because the pups in the F1 generation were exposed to nPB between weaning and sexual maturity (WIL, 2001). During occupational exposure, this period of exposure would not occur because children under age 16 are not allowed to work in industrial settings. However, EPA believes that because of the potential for in utero effects that would only be seen in the offspring generation, looking only at the F0 parental generation could underestimate the adverse health impacts of a chemical. Therefore, we believe it is appropriate to consider effects seen in both the F0 parental generation and the F1 offspring generation. Further, effects on sperm motility in the parental and offspring generations are seen at levels generally consistent with multiple reproductive effects seen in both generations and both sexes exposed to nPB, such as estrous cycle length, lack of estrous cycling, the number of estrous cycles in a given period of time, fertility indices, and the number of live pup births (TERA, 2004; ICF, 2006a; SLR International, 2001). Therefore, we believe that the available data indicate that in order to protect against adverse reproductive effects, an exposure level within the range of 17 to 30 ppm, would potentially be acceptable. We would reach the same proposed decisions of unacceptability based upon data from the F0 generation.
-
Evaluation of Acceptable Exposure Levels for the Workplace
To calculate acceptable exposure levels for nPB, EPA uses standard risk assessment methods delineated in Agency guidance (U.S. EPA, 1994b) in evaluating data, choosing a benchmark dose level or a NOAEL, and making the adjustments and uncertainty factors prescribed to account for differences in the duration of exposure and in sensitivity between and within species. Adjustment for Occupational Exposure Pattern
To account for differences between the exposure pattern used in the WIL study (6 hours per day for 7 days per week) when compared to a typical workweek of 8 hours per day and 5 days a week, a ``human equivalent concentration'' (HEC) is first calculated by adjusting the benchmark dose level:
(BMDL in ppm x 6 hours/8 hours) x 7 days/5 days = HEC (ppm)
HECs for the major health endpoints are shown in Table 6 above in section IV.E.1. Uncertainty Factors
According to EPA risk assessment guidance for reference concentrations (RfC) (EPA 1994a), uncertainty factors of up to 10 may be applied to the HEC for each of the following conditions:
(1) Data from animal studies are used to estimate effects on humans;
(2) Data on healthy people or animals are adjusted to account for variations in sensitivity among members of the human population (inter- individual variability);
(3) Data from subchronic studies are used to provide estimates for chronic exposure;
(4) Studies that only provide a LOAEL rather than a NOAEL or benchmark dose; or
(5) An incomplete database of toxicity information exists for the chemical.
EPA believes that two uncertainty factors are appropriate for this database to account for that: (1) Physiological differences between humans and rats; and (2) variability within the working population. The rationale for the use of these two uncertainty factors is described below.
EPA RfC guidelines state that an uncertainty factor of 10 may be used for potential differences between study animals and humans. This factor of 10 consists in turn of two uncertainty factors of 3--the first to account for differences in pharmacodynamics \14\ and the second to account for differences in pharmacokinetics \15\ between the study of animal and humans. (The value of three is the square root of 10 rounded to one digit, with 10 representing an order of magnitude (EPA,1994a). In practice, EPA uses the square root of 10 when there are two or four uncertainty factors of 3, yielding a total uncertainty factor of 10 or 100, and we use a value of 3 when multiplying by an uncertainty factor of 10). By EPA RfC guidelines (U.S. EPA, 1994b), no adjustment for differences in pharmacokinetics is necessary in this instance because the blood/air partition coefficient \16\ for nPB in the human (7.1) is less than in the rat (11.7), indicating that the delivered dose of nPB into the bloodstream in rats is slightly higher than in humans. Consistent with Appendix J of EPA's RfC guidelines for an inhaled compound that exerts its effects through the bloodstream, EPA applies an uncertainty factor of 1 for pharmacokinetics.
\14\ Pharmacodynamics refers to the biochemical and physiological effects of chemicals in the body and the mechanism of their actions.
\15\ Pharmacokinetics refers to the activity or fate of chemicals in the body, including the processes of absorption, distribution, localization in tissues, biotransformation, and excretion.
\16\ The blood/air partition coefficient is the ratio of a chemical's concentration between blood and air when at equilibrium.
However, EPA recognizes that the lack of an uncertainty adjustment for pharmacokinetic differences between animals and humans rests on a default approach applied to category 3 gases described in Appendix J of its guidelines for deriving an inhalation RfC. This default approach assumes that nPB's toxicokinetics follow a model in which: (1) The toxicity is directly related to the inhaled parent compound in the arterial blood, and (2) the critical metabolic pathways scale across species, with respect to body weight, in the same way as the ventilation rate. Given the hypothesized metabolic pathways for nPB (ICF, 2002a; CERHR, 2002a), it is plausible that toxicity in rats may be related to a reactive metabolite in the target tissue rather than the blood level of the parent compound. EPA is not aware of any quantitative data on nPB metabolism in humans, or evidence implicating the biologically active agent or mode of action. Some commenters on the June 2003 NPRM stated that EPA should use an uncertainty factor of 1 or 2 to extrapolate from animals to humans (Weiss Cohen, 2003), while others suggested uncertainty factors of 2 or 3 for pharmacokinetics, or an overall uncertainty factor of 10 for rat to human extrapolation because of a lack of information on the metabolism and mode of action of nPB and because the rat is an insensitive model for effects on male reproduction in humans (Werner, 2003; Rusch and Bernhardt, 2003). Commenters provided no data to indicate that (1) the toxicity is not directly related to the inhaled parent compound in the arterial blood, or (2) the critical metabolic pathways do not scale across species, with respect to body weight, in the same way as the ventilation rate. Recent studies provide additional data regarding metabolism of nPB in rats and mice (RTI, 2005), but data on human metabolism are still lacking.
One analysis of these metabolic data suggested that mice are less sensitive to the effects of nPB than rats and hypothesized that humans would also be less sensitive than rats (Stelljes, 2005). However, this analysis makes numerous assumptions about toxic nPB metabolites and metabolic activation pathways that have not been confirmed by experimental data. A review of this
[[Page 30185]]
analysis is available in the public docket (ICF, 2006c). Despite the difference in metabolic pathways for nPB in mice and rats (RTI, 2005), EPA finds no significant species-specific differences in toxicity exist between rats and mice at inhaled concentrations TM(TLV) of 10 ppm (time-weighted average) for nPB (ACGIH, 2005). ACGIH summarized numerous studies showing different effects of nPB and identified no observed effect levels (NOELs) of 200 ppm for hepatotoxicity (ClinTrials, 1997b) and less than 100 ppm for developmental toxicity, as evidenced by decreased fetal weight (Huntingdon Life Sciences, 2001).
OSHA has not developed a permissible exposure limit (PEL) for nPB that EPA could use to evaluate toxicity risks \17\ from workplace exposure. In prior SNAP reviews, EPA has used ACGIH TLVs where available in assessing a chemical's risks and determining its acceptability if OSHA has not set a PEL. ACGIH is recognized as an independent, scientifically knowledgeable organization with expertise in issues of toxicity and industrial hygiene. However, in this case, EPA believes that ACGIH's TLV for nPB of 10 ppm has significant limitations as a reliable basis for an acceptable exposure limit, especially given the availability of other, more comprehensive analyses described in this proposal. First, according to the authors of the Huntingdon Life Sciences study, the decrease in fetal weight was an artifact of sampling procedure that biased the data (test animals were only sacrificed at the end of the day rather than at random). The CERHR expert panel excluded ``aberrantly low'' fetal weights from one litter in this study and calculated a BMDL greater than 300 ppm for this endpoint after removing those outlier data (CERHR, 2002a, 2003a, and 2004a). TERA calculated a similar BMDL when analyzing the same data set (TERA, 2004). Further, the reference list in the documentation on the TLV indicates that ACGIH did not review and evaluate all the studies available prior to the development of the recommended exposure limit. For example, key supporting articles that reported disruption of estrous cycles (Yamada et al., 2003 and Sekiguchi et al., 2002) were not discussed in the TLV documentation. Further, ACGIH did not provide sufficient reasoning for the selection of the chosen endpoint over others (e.g., reproductive toxicity and/or neurotoxicity). The lack of discussion of applied uncertainty factors also prevents a determination of how ACGIH arrived at a TLV of 10 ppm. In summary, EPA is not basing its proposed acceptability determination for nPB on the ACGIH TLV because: (1) Other scientists evaluating the database for nPB did not find the reduced pup weight to be the most sensitive endpoint; (2) benchmark dose (BMD) analysis of the reduced pup weight data (CERHR, 2002a; TERA, 2004) results in a higher BMDL (roughly 300 ppm) than those for reproductive effects; and (3) ACGIH may not have reviewed the complete body of literature as several studies discussing neurotoxicity and female reproductive effects were omitted from the list of references. A number of reviews of this document are available in the public docket (ICF, 2004d; O'Malley, 2004).
\17\ Vendors of nPB-based products have recommended a wide range of exposure limits, from 5 ppm to 100 ppm (Albemarle, 2003; Chemtura, 2006; Docket A-2001-07, item II-D-19; Enviro Tech International, 2006; Farr, 2003; Great Lakes Chemical Company, 2001).
We note that, even if EPA had selected the ACGIH TLV as our basis for assessing the risks of nPB, we would have proposed the same determinations. In the specific coatings application that we propose to find acceptable subject to use conditions at the Lake City Army Ammunition Plant, exposure data showed an ability to meet an exposure level of 10 ppm, with the vast majority of measurements below that value. Thirty-four of 35 samples had concentrations below 10 ppm, and the mean concentration for the plant was less than 4 ppm (Lake City Army Ammunition Plant, 2004). For the aerosol and adhesive end uses, it would be even more difficult to achieve an exposure level of 10 ppm than to achieve a level in the range that EPA is considering (17 to 30 ppm). Thus, we would have proposed the same decisions for nPB of acceptable, subject to use conditions for coatings and unacceptable for aerosols and adhesives using the ACGIH's TLV of 10 ppm to assess health risks. Despite some flaws in its derivation, the TLV of 10 ppm is less than two-fold lower than the low end of the range of acceptable exposure levels based on the most sensitive reproductive endpoints. This small difference is well within the uncertainty required to extrapolate a benchmark dose from an experimental study in rats to an occupational exposure limit in humans.
-
Community Exposure Guideline
In this proposal, EPA is using a community exposure guideline (CEG) of 1 ppm to evaluate potential health risks among populations living near facilities using nPB. This community exposure guideline is an estimate of a continuous inhalation exposure (averaged over 24 hours per day, 7 days per week) to the general public (including sensitive subgroups) that is likely to be without an appreciable risk of adverse health effects during a lifetime.
Based on EPA risk assessment guidelines (US EPA, 1994b), the CEG was derived using the lowest BMDL from effects listed in Table 6 as the point of departure (110 ppm for vacuolation in the liver of animals in the F1 generation of WIL, 2001). The HEC was calculated as follows:
110 ppm x (6 hours exposure in study/24 hours avg time) x (7 days/7 days) = 28 ppm
EPA used an uncertainty factor of 3 for extrapolation from animals to humans, as discussed above in section VI.A, and an uncertainty factor of 10 for variability within the general population, consistent with EPA's RfC guidelines. Dividing the HEC of 28 ppm by 30 yields a community exposure guideline of approximately 1 ppm. If we had used sperm motility (HEC of 42 ppm based on a BMDL of 169 ppm) or number of estrous cycles (HEC of 40 ppm based on a BMDL of 162 ppm) as starting points, we would calculate the same approximate CEG value. We note that, following RfC guidelines, EPA's community exposure guideline includes a number of conservative assumptions, including exposure adjustments to protect an individual exposed for up to 24 hours a day for 70 years (U.S. EPA, 1994b, p. 1-5).
EPA evaluated general population exposure using EPA's SCREEN3 (U.S. EPA, 1995b) air dispersion model to assess the likely maximum concentration of nPB from single sources.\18\ EPA used data collected from
[[Page 30188]]
actual facilities (Swanson, 2002) to characterize two scenarios: (1) A typical large, high-use adhesive application facility where the closest resident is 100 meters away; and (2) a smaller facility with average- use adhesive application in an urban area, where the nearest resident is only 3 meters away. The results indicated that modeled exposures in either scenario did not exceed the CEG of 1 ppm. The highest exposure modeled was 0.24 ppm at a distance of 3 meters away from the source in the urban scenario, while most other exposures were at least an order of magnitude lower (ICF, 2003; ICF, 2006a). Because the community exposure guideline was not exceeded for any of the exposure scenarios in this conservative screening approach, EPA has concluded that nPB exposure to populations living close to facilities using nPB is not a concern for purposes of determining the acceptability of nPB under the SNAP program.
\18\ We performed the modeling for a facility using nPB-based adhesives because the nPB emissions from this type of facility were expected to be higher than those from facilities using nPB for other end uses. Thus, if a facility using adhesives would not result in emissions exceeding the CEG, facilities using nPB in aerosols or in metals, electronics, or precision cleaning also would not result in emissions exceeding the CEG.
-
-
What listing is EPA proposing for each end use, and why?
In this rule, EPA is proposing to find nPB unacceptable in adhesive and aerosol solvent end uses, and acceptable subject to use conditions in the coatings end use. The proposed listings, summarized in Table 9, are intended to allow the use of nPB where it does not pose a human health risk significantly greater than other substitutes and prohibit nPB's use where nPB exposure cannot be maintained, or is unlikely to be maintained, at even the highest level considered in this proposal (i.e., 30 ppm). We also are taking comment on an alternate approach of finding nPB acceptable subject to use conditions in the above end uses (see Section VII.A).
Table 9.--Proposed Decisions by End Use and Sector
And our proposed For nPB in this sector and Our proposal is to alternate approach end use:
list nPB as:
is:
Aerosols:
Aerosol solvents........ Unacceptable........ Acceptable, subject to use conditions.\2\ Adhesives, Coatings, and Inks:
Coatings................ Acceptable, subject Acceptable, subject to use conditions to use \1\.
conditions.\2\
Adhesives............... Unacceptable........ Acceptable, subject to use conditions.\2\
\1\ Use of nPB in this end use is limited to coatings at facilities that, as of May 30, 2007, have provided EPA information demonstrating their ability to maintain acceptable workplace exposures (i.e., the Lake City Army Ammunition Plant). \2\ Use conditions would include proposed requirements that users must (1) meet an exposure limit of 20 ppm on an eight-hour time-weighted average, (2) monitor workers' exposure to nPB using a personal breathing zone sampler on an eight-hour time-weighted average initially and periodically (every 6 months or longer, depending on the concentration during initial monitoring), and (3) keep records of the worker exposure data on site at the facility for at least three years from the date of the measurement.
-
Aerosol Solvents
In this rule, EPA proposes to find nPB unacceptable in the aerosol solvent end use. There are a number of aerosol solvent alternatives that do not pose any risk for ozone depletion or for ground level smog formation.\19\ EPA's greatest concern with nPB-based aerosols is that users of nPB as an aerosol solvent cannot reliably maintain exposures at sufficiently low levels to ensure that workers are protected. This finding is based on measured exposure data and model estimations indicating the likelihood of elevated concentrations associated with nPB-based aerosols given typical ventilation conditions. A number of other acceptable solvent alternatives are available that can be used at exposure levels below their respective acceptable exposure limits.
\19\ Smog, also known as ground-level ozone, is produced from emissions of volatile organic compounds that react under certain conditions of temperature and light.
Ventilation conditions are an important consideration in evaluating potential risks within this end-use category. ``Benchtop cleaning'' of individual parts, which is feasible under exhaust hoods or in spray booths with adequate ventilation, comprises 25% or less of the market involving ODS substitutes for aerosols (U.S. EPA, 2004). According to industry information and several commenters, the majority of the market for nPB-based aerosols involves in-place applications requiring a portable aerosol, such as cleaning energized electrical contacts and switches, maintenance in underground mines, or cleaning active elevator motors (CSMA, 1998; U.S. EPA, 2004; Williams, 2005). These applications often occur in tightly confined spaces where it is not feasible to install ventilation equipment or remove parts to ventilated areas (CSMA, 1998; Linnell, 2003; Werner, 2003). Other acceptable substitutes, such as blends of HFEs or HFCs and trans-dichloroethylene, are available in these end uses. One commenter also suggested that a user of an nPB-based aerosol will assume that they are being provided with a product that offers similar margins of safety as the product being replaced (i.e., HCFC-141b) and therefore can be used under the same conditions (Werner, 2003).
The likelihood that nPB aerosol solvents would be used in poorly ventilated spaces is of particular concern given the likelihood of elevated exposure levels. The exposure data from aerosol solvent use are extremely limited. These data are from simulations of a number of situations where nPB might be used, such as benchtop cleaning of electronics and cleaning automotive brakes, rather than data from facilities currently using nPB in manufacturing or maintenance processes. Thus, the available exposure data may not be representative of ventilation levels normally used with nPB-based aerosols and may not adequately represent exposure levels during in-place cleaning, industry's most common application for nPB-based aerosols. The distribution of exposure levels in the seven samples ranging from 5.5 to 32 ppm corresponded to the range of ventilation rates reported--0, 300, 640, and 1900 cfm--with the highest ventilation rate resulting in the lowest exposure levels and the lower ventilation levels resulting in the values above 30 ppm. The ventilation rate most consistent with use in a confined space for in-place cleaning, 0 cfm, resulted in half the exposures (one of two) exceeding 30 ppm. The highest ventilation rate, 1900 cfm, occurred at a vented booth, which would not be feasible to install for in-place cleaning applications--the majority of applications for nPB-based aerosols. The middle ventilation rates of 300 and 640 cfm occurred during use of a fan for an entire room (regional ventilation), as might be expected for benchtop cleaning (Confidential submission, 1998), but not for in-place cleaning in confined spaces. In modeling nPB exposure from aerosol solvent use at a low ventilation rate of
[[Page 30189]]
450 cfm, a level that might be expected during benchtop cleaning, 8- hour average concentrations of 16.5 to 33 ppm are predicted, depending on the amount of nPB used (ICF, 2006a). Exposure levels for confined spaces with even lower ventilation rates, as we would expect for in- place cleaning, would be even higher, likely exceeding the high end of the range that EPA is considering. Short-term exposures of 370 and 1,100 ppm taken from workers' collars in a room with regional ventilation at 640 cfm, when averaged over an 8-hour period, resulted in exposure levels of 12 and 34 ppm. These exposures occurred as a result of using nPB over a period up to 15 minutes, so it is likely that users would have greater exposure than 30 ppm if they used nPB for longer than 15 minutes per day, as with multiple uses. The available data sets have a small sample size, may not be representative of in- place cleaning in confined spaces, and do not provide EPA with convincing data that nPB is likely be used safely, at exposure levels at or below the highest level in the range we are considering for evaluation of acceptability.
EPA is concerned that many, and perhaps most, uses of nPB aerosol solvents result in a high probability of exposures at or above even the upper end of the range of exposures that the Agency is considering to be potentially acceptable. EPA is aware of no data on ventilation levels demonstrating that most users of aerosol solvents, or of nPB in particular, would use aerosols in locations with sufficiently high ventilation levels to protect human health (e.g., 1900 cfm or greater). We request data on worker exposure levels, typical ventilation rates, and patterns for usage of nPB-based aerosols, considering both benchtop and in-place use.
EPA has found numerous other aerosol solvents acceptable. These aerosol solvents can be used safely in a manner consistent with their respective acceptable exposure limits. This is highlighted in a study comparing concentrations of eight different chemicals that are acceptable under the SNAP program in aerosol formulations: HFE-7100, HFE-7200, trans-1,2-dichloroethylene, HCFC-225ca and -225cb, acetone, pentane, and HFC-134a. In this study, with ventilation of only 48 cfm, 8-hr TWA exposure from the different chemicals varied from 35.5 ppm to 194.0 ppm, and all chemicals met their respective recommended exposure levels (ICF, 2006a). As discussed above in section V.A, when these concentrations are adjusted for the chemicals' respective molecular weights, they would correspond to nPB concentrations of 29.5 to 394.4 ppm, which is at or above even the highest level the Agency would consider acceptable. The ventilation level in this study is closer to what we would expect in a confined space where fans or vents cannot be installed, as for in-place cleaning. Based on these considerations, the Agency believes that nPB used as an aerosol solvent would impose significantly more risk to human health than other alternatives available for this end use.
-
Adhesives
EPA proposes to find nPB unacceptable in the adhesive end use. As for aerosol solvents, we found that some alternative adhesive formulations could reduce particular environmental risks more than nPB, such as generation of ground level ``smog'' or ozone depletion potential. However, we find the greatest concern in this end use is with nPB's human health effects. We propose to find nPB unacceptable in adhesives because it poses significantly greater risk to human health as compared to other available alternatives in this end use.
In the June 2003 NPRM, we initially proposed to find nPB acceptable in adhesives based on the SNAP program principle that ``EPA does not intend to restrict a substitute if it poses only marginally greater risk than another substitute * * *. The Agency also does not want to intercede in the market's choice of available substitutes, unless a substitute has been proposed or is being used that is clearly more harmful to human health and the environment than other alternatives.'' (68 FR 33294, citing the original March 18, 1994 SNAP rule at 59 FR 13046). At the time of the proposal, we considered data from NIOSH monitoring and health hazard evaluations for three facilities using nPB-based adhesives. At two of the three facilities, NIOSH worked together with the companies to install state-of-the-art ventilation equipment. Looking at exposure data from all workers after ventilation improvements, we believed it would be possible for facilities to meet the proposed AEL of 25 ppm (68 FR 33294).
One public commenter suggested that EPA should reconsider whether industrial exposures consistently occur and/or can be controlled to a level at or below 25 ppm (Werner, 2003). We reevaluated the exposure data for the two plants that had improved their ventilation, focusing on exposure to the workers that receive the highest exposures because they directly spray the nPB-based adhesive. We found that, even in the best case, a substantial number of workers spraying nPB-based adhesives would be exposed above the highest level in the range we are considering.
NIOSH investigators initially reported that mean exposures to nPB ranged from 60 to 381 ppm (8-hour time weighted averages) at three different foam-fabrication facilities using nPB-based adhesives (NIOSH, 2000a, 2000b, 2001, 2002a, 2002b, 2003a). In one facility, average (mean) nPB exposures were reduced from 169 ppm to 19 ppm, following installation of ventilation equipment (NIOSH, 2000b). Although use of spray booths at this facility reduced the average exposure level to 19.4 ppm for all workers, the majority of the sprayers directly using nPB-based adhesives still would be exposed at unacceptably high levels. Out of fourteen sprayers at the Custom Products facility:
Six, or 43% of sprayers, would be exposed to more than 30 ppm.
Nine, or 64% of sprayers, would be exposed to more than 25 ppm.
Ten, or 71% of sprayers, would be exposed to more than 20 ppm.
Eleven, or 79% of sprayers, would be exposed to more than 15 ppm.
Thirteen, or 93% of sprayers, would be exposed to more than 10 ppm.
At another facility using nPB-based adhesives, the average exposure was reduced from 58 pm to 19 ppm after the company installed ventilation recommended by NIOSH (NIOSH, 2001). Data on exposure for sprayers found fewer individuals receiving high exposures than at the facility monitored in NIOSH (2000b), but 65% (22 of 34) of exposure samples for sprayers were higher than 15 ppm, 33% (11 of 34) were higher than 20 ppm and 15% (5 of 34) were higher than 25 ppm after improving ventilation.
Overall, 42% of sprayers in these two facilities using nPB-based adhesives were exposed to concentrations of nPB greater than 20 ppm (21 of 48 workers) and 23% (14 of 48 workers) were exposed to more than 25 ppm, even after installing state-of-the-art ventilation with assistance from NIOSH. Sprayers had significantly higher individual exposures than workers who did not work directly with the nPB-based adhesive.
In response to public comment and additional information available to EPA since the June 2003 NPRM, we now propose that use of nPB-based adhesives poses significantly higher risks to human health than other available adhesives. Since the June 2003 NPRM, there have been a number of reports of
[[Page 30190]]
workers working with nPB-based adhesives that have suffered adverse, persistent neurological effects that resulted in hospitalization (Beck and Caravati, 2003, and Majersik et al., 2004, 2005; Calhoun County, 2005; Miller, 2005; Raymond and Ford, 2005). Based on data from actual facilities using adhesives, it is estimated that a facility using nPB with average adhesive application rates and average ventilation rates would have exposure levels of approximately 60 ppm on an 8-hr time- weighted average (ICF, 2006a). Modeling of exposures at high adhesive application rates and average or lower ventilation rates resulted in exposures of approximately 250 to 2530 ppm (ICF, 2006a). We believe these modeling results show that most adhesive users would exceed acceptable exposure levels by significant margins and that it is unlikely that adhesive users would be able to use nPB safely.
Considering the exposure data for nPB-based adhesives, we believe it is unlikely that, even with improved ventilation, adhesive users could reduce exposures to acceptable levels on a consistent basis. In the best case seen, a facility with low to average initial exposure levels was able to reduce exposures to the middle of the range EPA is considering after extensive assistance from NIOSH in installing state- of-the-art ventilation. We expect that many facilities will begin with higher exposure levels and will not have the same level of assistance to improve ventilation, thus making it unlikely that they would achieve acceptable exposures. Given the information above, we are concerned that nPB-based adhesives cannot be reliably used in a manner that protects human health. We request comment and further data on whether it is feasible to use nPB-based adhesives with worker exposure levels consistently at or below any of the values in the range of exposure levels that EPA is considering potentially acceptable (i.e., 17 to 30 ppm).
The available information indicates that all acceptable carrier solvents in adhesives other than nPB have projected or actual exposure less than the appropriate workplace exposure limit EPA used in finding those substitutes acceptable. Examples of other carrier solvents currently used in adhesives and acceptable under the SNAP Program include hydrocarbon solvents, acetone, methylene chloride, and water. EPA finds that there are other available alternatives that pose significantly less risk to human health and the environment compared to nPB in the adhesives end use.
During the public comment period on the June 2003 NPRM, one commenter representing the adhesives industry stated that there are some small but critical applications that require nonflammability and high solvency (Collatz, 2003). The commenter did not specify what those applications are, and whether there was information showing that other types of adhesives, such as those using water, flammable solvents, or methylene chloride, are technically infeasible in these applications. We request comment and data on whether there are any unique applications in the adhesives end use for which there are no technically feasible alternatives other than nPB and thus, for which nPB should be allowed. If so, and if determined that nPB should be unacceptable except where no other substitutes are feasible, we would consider finding nPB acceptable subject to narrowed use limits, with requirements for each end user to perform a demonstration that there are no other technically feasible alternatives for their particular site, to install local exhaust ventilation equipment designed to reduce exposures to acceptable levels and to perform worker exposure monitoring. Alternatively, if there was sufficient information provided during the public comment period showing that there are applications in which nPB can be safely used, we would consider finding nPB acceptable in adhesives, subject to use conditions requiring installation of local exhaust ventilation and worker exposure monitoring. This would allow for use of nPB in any applications where it may be used safely if any such applications exist.
-
Coatings
We are proposing to find nPB acceptable, subject to use conditions, for facilities that, as of May 30, 2007, have provided EPA information demonstrating their ability to maintain workplace exposure levels below even the minimum level of the range of exposures that EPA is considering to be potentially acceptable (i.e., 17 to 30 ppm). The SNAP submission with information on coatings was made for a single facility and EPA is unaware of anyone else interested in using nPB in this end use. Therefore, there are currently no analyses indicating whether nPB would pose significantly greater risks in any coating applications other than this facility. Workplace exposure levels to nPB from ammunition sealant at Lake City Army Ammunition Plant ranged from less than 1 ppm up to 21 ppm on an eight-hour time-weighted average. Thirty- four of 35 samples had concentrations below 10 ppm, and the mean concentration for the plant was less than 4 ppm (Lake City Army Ammunition Plant, 2004). The vast majority of measurements show worker exposure well below the lowest level in the range of exposures that EPA is considering. Thus, we believe that nPB can be used as safely as other acceptable solvents used at their acceptable exposure limits under the conditions at this facility.
Other acceptable substitutes for ozone-depleting substances in coatings, in general, include oxygenated solvents, hydrocarbon solvents, terpenes, hydrofluoroethers 7100 and 7200, benzotrifluorides (include parachlorobenzotrifluoride), monochlorotoluenes, trans-1,2- dichloroethylene, chlorinated solvents, water-based formulations, and high-solids formulations. In the particular application for ammunition coatings, the submitter evaluated a large number of alternatives and found that n-propyl bromide was the only one of 29 solvents tested that could meet performance specifications at this facility (Harper, 2005). Thus, it is not clear that there are other substitutes available for this specific application, and exposure data show that in this specific application, nPB can be used in a way that does not pose significantly greater risks to human health compared to other acceptable substitutes in the coatings end use.
-
-
What other regulatory options did EPA consider?
EPA considered several different options, but we prefer the approach proposed in this rule. We also take comment on the options discussed below.
-
Alternate Option for Comment: Acceptable With Use Conditions Requiring Exposure Limit and Monitoring
We also take comment on a proposed alternate approach in which nPB would be acceptable subject to use conditions in all the end uses addressed in this action. Under this alternate approach, users would meet an exposure limit, monitor exposure of workers using nPB, and keep records to demonstrate compliance with these requirements. For purposes of this alternative proposal, we selected 20 ppm to use as an exposure limit above which use would be unacceptable, and 10 ppm as an action level that allows reduced exposure monitoring, for the reasons discussed below in section VII.A.1, ``Use Conditions and Their Rationale.'' However, we are soliciting comment on whether a different exposure level within the 17 to 30 ppm range should
[[Page 30191]]
be selected. The following requirements would apply at each facility where nPB is used: Exposure Limit
The owner or operator would be required to ensure that workers using nPB are exposed to no more than 20 ppm on an 8-hour time-weighted average. The exposure limit could be met through engineering controls (e.g., ventilation equipment), work practices, or reduced use of nPB. Initial Worker Exposure Monitoring
For each facility where nPB is used, the owner or operator of the facility would be required to ensure that personal breathing zone air samples of each nPB user's exposure would be collected on an eight- hour, time-weighted average initially within 90 days after a final rule becomes effective. Monitoring measurements may be taken with an organic chemical monitoring badge on the collar or a tube filled with charcoal on the collar. Periodic Exposure Monitoring
(1) The owner or operator of the facility would be required to ensure that personal breathing zone air samples of user exposure are collected periodically on an eight-hour, time-weighted average depending on the results of the most recent set of exposure data. A monitoring program could be instituted by the company or by the nPB supplier for that facility. Periodic sampling requirements would be based on the most recent monitoring results, as follows:
Table 10.--Alternative Approach Exposure Levels and Periodic Exposure Monitoring
If exposure measurements for nPB are at this level:
Then the owner or operator:
all measurements at or below 10 ppm.... is not required to perform periodic exposure monitoring. all measurements at or below 20 ppm, must take personal breathing with some measurements above 10 ppm. zone samples again at least once in the next six months. at least one measurement above 20 ppm.. must stop using nPB in the application exceeding the exposure limit until exposure data show that 20 ppm can be consistently met in the vast majority of cases. unknown, in cases of new workplace must take personal breathing conditions increasing exposure or new zone samples as a test before applications of nPB.
using nPB in new industrial applications or conditions, or within 7 days of an emergency caused by a leak, rupture or breakdown, and use this value to determine the next time monitoring is required.
(2) For periodic monitoring, the owner or operator would be allowed either to monitor each nPB user's exposure, or to monitor exposure of a representative nPB user in each job classification in a work area during every work shift, where the monitored nPB user is expected to have the highest exposure.
(3) The owner or operator would be allowed to discontinue the periodic 8-hour TWA monitoring for nPB users at the facility where at least two consecutive sets of measurements taken at least seven days apart are below 10 ppm. Monitoring for New Conditions or Applications
Whenever there is a change in workplace conditions that may increase exposure or whenever a new application of nPB is introduced, the owner or operator would be required to take personal breathing zone samples accounting for all nPB users as a test before using nPB in manufacturing or repair. These could be either samples for each nPB user or samples representing each job classification in a work area during a work shift, so long as the samples are based on the user with the likely highest exposure. Examples of changes in workplace conditions that may increase exposure include changes in production, process control equipment, or work practices, or a leak, rupture, or other breakdown.\20\ Examples of introduction of a new application of nPB include aerosol contact cleaning in a location with regional ventilation or natural ventilation, where previous measurements were carried out on workers in a location with local ventilation. If the change occurs because of an unpredictable emergency, then the owner or operator would need to ensure exposure monitoring takes place within 7 days of the change.
\20\ See 29 CFR 1910.1052(d)(4)(i).
Sampling Methods and Accuracy
Exposure samples would be required to be analyzed either by NIOSH method 1003 for halogenated hydrocarbons or method 1025 for 1- bromopropane and 2-bromopropane or by another method that is accurate to 25% at the 95 percent confidence level. Recordkeeping Requirements
The owner or operator of the facility would be required to keep records of the monitored exposure data at the facility for at least three years from the date the measurements were taken for purposes of this rule. These records would be required to be made available in the event of a facility inspection or a request for the data by EPA. Note that the EPA's recordkeeping requirement does not affect OSHA's standard on access to employee exposure and medical records, which requires retaining any exposure records for at least 30 years (29 CFR 1910.1020(d)(ii)).
The regulatory listings by end-use under this alternate approach that the Agency requests comment on would be as follows:
BILLING CODE 6560-50-P
[[Page 30192]]
[GRAPHIC] [TIFF OMITTED] TP30MY07.000
[[Page 30193]]
[GRAPHIC] [TIFF OMITTED] TP30MY07.001
BILLING CODE 6560-50-C
[[Page 30194]]
1. Use Conditions and Their Rationale
The major provisions of the use conditions and the related issues that EPA considered in developing the alternate approach that we are taking comment on are as follows:
Exposure limit. A requirement to meet a workplace exposure limit would be an interim measure to ensure that nPB will be used safely until OSHA issues a final permissible exposure limit (PEL) under the Occupational Safety and Health Act. In the event that OSHA issues a final PEL, it would supersede EPA's exposure limit. EPA is specifically deferring to OSHA, and has no intention to assume responsibility to displace OSHA's authority under Public Law 91-596. EPA's exposure limit would not pre-empt the authority of OSHA to take regulatory or enforcement action with respect to exposure to this substance. This is made clear by the Clean Air Act under which EPA would promulgate this regulation (Subchapter VI--Stratospheric Ozone Protection), which provides at 42 U.S.C. 7610 in pertinent part: ``* * * this chapter
[Chapter 85--Air Pollution Prevention] shall not be construed as superseding or limiting the authorities, under any other provision of law, of the Administrator or any other Federal officer, department, or agency.'' By issuing an exposure limit for nPB, EPA's intention would be to fill existing regulatory gaps during the interim period of substitution away from ozone-depleting compounds and provide the needed margin of protection for human health and the environment until OSHA develops other regulatory controls or standards under appropriate authorities.
As discussed above in section IV.E.1, EPA is considering exposures within the range of 17 to 30 ppm as potentially acceptable in order to determine whether nPB may be used safely in each end use. For purposes of having a clear compliance target under this alternative approach for public comment, we are using 20 ppm as the exposure limit above which use would be unacceptable. We chose this value because we expect it to be protective against the reproductive and developmental effects identified previously (live litter size, sperm motility, estrous cycles). Worker exposure monitoring. The worker exposure monitoring requirements under the use conditions in the alternate approach were modeled after OSHA's requirements for monitoring for methylene chloride. 29 CFR 1910.1052(d). We expect that the regulated community would be familiar with this approach and there might be fewer changes for regulated businesses if OSHA later were to establish a workplace standard for nPB. Because the exposure limit would be an 8-hr TWA value that is derived from studies that measured exposure via inhalation, the proposed use conditions require the owner or operator to monitor 8-hr TWA values that measure workers' exposure in the breathing zone (e.g., samples from a worker's collar). We are not proposing to monitor short- term exposures because acute, short-term exposures of nPB are not of significant health concern, so long as long-term exposures are below the 8-hour TWA limit or potentially acceptable exposure levels (ERG, 2004).
Option for monitoring representative set of workers. Personal breath zone samples could be taken either from each worker using nPB or from a representative \21\ set of exposed workers expected to have the highest exposure. Allowing exposure monitoring from representative workers using nPB, rather than requiring separate monitoring for each individual using nPB, would reduce overall compliance burden, while still detecting any exposure levels in excess of the exposure limit and avoiding underestimates of exposure.
\21\ In its methylene chloride standard, OSHA defined representative sampling as follows: ``The employer has taken one or more personal breathing zone air samples for at least one employee in each job classification in a work area during every work shift, and the employee sampled is expected to have the highest * * * exposure.'' (29 CFR 1910.1052(d)(1)(ii)(A)).
Initial monitoring. Users already using nPB would need to undergo exposure monitoring no later than 90 days after the date the final rule becomes effective. A user that has never used nPB before would need to perform initial monitoring before beginning to use nPB in the facility's industrial applications.
Periodic monitoring. Monitoring would have to be performed periodically on a schedule based on the results of the most recent set of exposure monitoring data. Monitoring from workers' personal breathing zone would be required during the next six months if an initial measurement finds exposure levels between the action level \22\ and the 8-hour TWA exposure limit. No periodic monitoring would be required if initial measurements are below the action level. The action level would be the value that is half the exposure limit, in this case 10 ppm. OSHA standards also set an action level of half the PEL.
\22\ The action level is the exposure level that is half the 8- hour TWA exposure limit. In this case, the action level would be10 ppm.
Under the alternate approach, monitoring would no longer be required where the most recent exposure monitoring data found all worker exposures at or below 10 ppm. OSHA rules also reduce monitoring requirements for exposures below the action level because if measured values are that low, it is unlikely that any measurement will exceed the PEL unless a major change to the process occurs.
Monitoring for changes in workplace conditions or nPB use. New monitoring would be required if an event occurs that would make the most recent set of monitoring data no longer representative. EPA would expect that the owner or operator would plan new applications of nPB or changes to control equipment or work practices and would perform a test for worker exposure levels before using nPB on a regular basis in that application. In the case of an emergency, such as a breakdown of ventilation equipment or a leak, we would expect exposure monitoring to be performed as soon as possible, and no later than 7 days after the change in workplace conditions. This period is intended to give an owner or operator time to locate and purchase exposure monitoring equipment in an emergency where the equipment may not already be available at the facility.
Monitoring method and accuracy. We take comment on the use of NIOSH methods 1003 and 1025 (NIOSH, 2003b and c) for analyzing nPB exposure under the proposed alternate approach. Several of the studies that supplied EPA with exposure data used this method and they are standardized methods prepared by NIOSH, a recognized authority on industrial hygiene. In addition, we would allow other methods that are accurate to 25% at the 95 percent confidence level. Based on the accuracy of available methods, most OSHA standards require exposure monitoring accurate to 25% at the 95 percent confidence level, as in the methylene chloride standard (29 CFR 1910.1052(d)(1)(iii)(A)) and other OSHA standards.
Recordkeeping requirements. We would require that users keep records of the worker exposure data for three years from the date the measurement is taken.\23\ This would provide information allowing EPA to determine if facilities are complying with the exposure limit and if workers exposed to nPB are sufficiently protected.
\23\ OSHA's standard on access to employee exposure and medical records requires retaining exposure records for at least 30 years (29 CFR 1910.1020(d)(ii)), and these requirements would not be affected by this regulation.
Responsibility for meeting requirements. Under the alternate approach, the owner or operator of a
[[Page 30195]]
facility using nPB would be responsible for meeting the rule's use conditions. 2. Advantages and Disadvantages of the Alternate Approach
Setting use conditions that require users to meet an exposure limit and to monitor and keep records to demonstrate achieving the limit would protect the health of nPB users while giving industry more flexibility and more options for ODS substitutes, compared to finding nPB unacceptable. This could be especially useful for users of HCFC- 141b as an aerosol solvent that are seeking an effective ODS substitute. If there were any situations in which other available alternatives did not provide as good performance, nPB would still be available as an option, provided the use conditions could be met. The monitoring requirements would encourage good industrial hygiene and safe use of nPB.
Considering the list of use conditions above, we believe that setting use conditions requiring an exposure limit, worker exposure monitoring, and recordkeeping would be complex and potentially confusing. Requiring users to meet the exposure limit, although providing greater potential flexibility, also would provide less certainty about how to comply. A user could spend considerable time and expense trying to meet the exposure limit, only to find that it is not achievable.
Given the limited circumstances under which we expect aerosol and adhesive users could meet an acceptable exposure limit and given the availability of other, less toxic alternatives in both of these end uses, EPA's preferred option is to find nPB unacceptable in aerosols and adhesives. Further, considering that without regulatory requirements, the users of nPB at the Lake City Army Ammunition Plant have been operating with the vast majority of exposure levels below 17 ppm, the low end of the range of exposures that EPA is considering to be potentially acceptable (Lake City Army Ammunition Plant, 2004), it appears unnecessary to require an exposure limit in that application.
-
Regulatory Options Where nPB Would Be Acceptable With Use Conditions Requiring Specific Equipment
We considered use conditions for the adhesive and aerosol solvent end uses that would reduce the human health risks of using nPB by reducing exposure levels with requirements for installation and use of ventilation equipment. We also offer for comment use conditions that would require aerosol dispensing equipment that would reduce exposure levels and that would allow use of aerosol blends with reduced amounts of nPB to maintain acceptable exposure levels. 1. Aerosols
For the aerosol solvent end use, EPA considered proposing a requirement for installation of ventilation equipment. Such a use condition would need to specify and define which kinds of ventilation equipment would be necessary. For example, because one study on exposure levels found that exposure levels reliably fell in or below the range that EPA is considering (i.e., 17 to 30 ppm) only where both local exhaust ventilation and regional ventilation equipment were used, a possible requirement would be for installation of both local exhaust ventilation and regional ventilation. We would define local exhaust ventilation as ventilation that removes vapors from a specific work location using ducts and fans. We would define regional ventilation as ventilation that moves air around in a large working area, such as one or more fans used for an entire room. A problem with requiring the type of ventilation equipment that all facilities must use is that it still might not provide enough ventilation in some situations and in other situations may be unnecessary to meet an exposure limit.
Another approach for aerosols we considered was to require a specific level of ventilation. Possible criteria for the level of ventilation would be the air flow rate, in cubic feet per minute (cfm) or cubic meters per second, or the face velocity at the location where a user would work, in feet per minute (fpm) or meters per second face velocity. Based on both modeling and exposure data from one study (ICF, 2006a; Linnel, 2003), an appropriate air flow rate for nPB-based aerosols would be greater than 1900 cfm and an appropriate face velocity would be 170 fpm. Alternatively, we considered requiring that facilities meet the guidelines for face velocity in spray booths from the ACGIH Ventilation Manual, in the range of 100 to 150 fpm, depending on the specific type of booth (ACGIH, 2002).
These options would appear to provide greater flexibility for industry compared to finding nPB unacceptable in aerosol solvents. However, our understanding is that in most aerosol applications, it might not be feasible to install adequate ventilation, and thus, to reduce human health risks. In the case of benchtop cleaning or degreasing, such as during rework of individual parts that are not yet sufficiently clean, it is possible to transport the part to a hood or spray booth to provide sufficient ventilation. However, for applications that require in-place cleaning such as cleaning energized electrical contacts and switches, maintenance in underground mines, or cleaning hot elevator motors, it is not feasible to install ventilation equipment in place or to remove the parts for cleaning in ventilation equipment (CSMA, 1998; Linnell, 2003). Information available to EPA shows that benchtop cleaning is perhaps 25% or less of the market for the ODS being replaced in aerosols (US EPA, 2004) and that electrical contact cleaning makes up the vast majority of the market for nPB-based aerosols (Williams, 2005); thus, we expect that necessary ventilation cannot be installed in most aerosol applications for nPB. It would be difficult to explain and potentially confusing for users that an aerosol product may be used for cleaning in one location in a facility, but not in another, particularly when the ODS being substituted for could be used in all locations at safe exposure levels. Further, it would be difficult for EPA to enforce use conditions on ventilation equipment, because aerosols are portable and can easily be used outside of the ventilation equipment. Other acceptable substitutes, such as blends of HFEs or HFCs and trans-dichloroethylene, are available in these end uses.
Another option that the Agency considered is finding nPB acceptable as an aerosol solvent, subject to the use condition that the aerosol product must be dispensed from a device or a system that is capable of maintaining acceptable exposure levels. The Agency is aware of at least two remote dispensing systems that could potentially mitigate exposures when used with low-pressure aerosols (Micro Care's Trigger GripTMand Miller Stephenson's Cobra[supreg] Solvent Spray Cleaning Brush). Vendor data indicates that each aerosol can may last twice as long when using a remote dispensing system, compared to standard aerosol usage, indicating the ability to halve average exposure levels and reduce total solvent use (Micro Care, 2006). However, these types of systems would only be practical for benchtop cleaning, and not electrical contact cleaning, which comprises the majority of nPB aerosol use. The Agency requests comment on the viability and enforceability of a use condition requiring aerosol dispensing systems or other mitigation devices that could provide sufficient performance while
[[Page 30196]]
ensuring acceptable workplace exposure levels of nPB.
Finally, the Agency considered another option by which the use of nPB would be acceptable in aerosol solvent uses, subject to the condition that users may only use blends of no more than fifty percent nPB and the remainder being propellants and other solvents, with manufacturer's recommended exposure guidelines for compounds other than nPB being no lower than 100 ppm. Based on exposure modeling performed on simulations of several commercial blends of nPB and another compound with a higher exposure limit (HFC-365mfc), it appears that users should be able to maintain exposures reliably below the range that EPA is considering for acceptability (i.e., 17 to 30 ppm) when using a blend containing no more than fifty percent nPB by weight at the ventilation levels modeled (ICF, 2006a). We note that the modeling does not consider the possibility that a user might need to use more of a blend with less nPB, since nPB is more aggressive than many other solvents used in aerosols. It also does not address exposure levels in confined spaces as might occur during in-place cleaning with aerosols. We request comment and relevant, empirical data on the 8-hour TWA exposures that can be reliably attained when using blends containing 50% or less of nPB by weight. In order to make this option enforceable, EPA would require users to keep records of nPB-containing aerosol blends they purchase, including the MSDS or other documentation of the proportion of nPB in the blend they use. We request comment on whether this is a feasible, enforceable option and whether it would provide useful flexibility to industry while ensuring adequate health protection. 2. Adhesives
EPA also considered use conditions for ventilation equipment or for specific ventilation levels for use of nPB-based adhesives. However, to date, we have found no study that demonstrates a ventilation option that could consistently achieve even the highest level within the range that EPA is considering for acceptability when using spray adhesives. Even with state-of-the-art ventilation equipment installed with the expert assistance of NIOSH, adhesives users were not able to lower exposure limits sufficient to protect the vast majority of their workers. Modeling of different levels of adhesive usage and ventilation, based on conditions at different facilities indicates that air flow rates would need to be more than 100,000 cfm. Even this high air flow rate might not be sufficient, since an air flow rate of 28,500 cfm resulted in exposure levels of 3.5 to 35 times an acceptable exposure level, depending on the amount of adhesive used (ICF, 2006a, Att. D). Less toxic substitutes such as water-based adhesives and acetone-based adhesives are available in this end use.
-
-
What are the anticipated costs of this regulation to the regulated community?
As part of our rulemaking process, EPA estimated potential economic impacts of this proposed regulation. In our analysis, we assumed that capital costs are annualized over 15 years or less using a discount rate for determining net present value of 7.0%. Because the use condition for coatings still permits nPB's use in the only known coatings application using nPB, we find no additional cost to the user community from this regulatory provision. We found that if this proposed rule were to become final, the cost to the user community of the unacceptability determinations, which are regulatory prohibitions on the use of nPB in adhesives and aerosols, would be in the range of $2.3 to $6.7 million per year for adhesive users and $36.3 to 39.7 million per year for aerosol users.
EPA also estimated the cost to the user community of the use conditions in the proposed alternate approach for aerosols, adhesives, and coatings. The requirements for users to meet an acceptable exposure limit and to perform exposure monitoring would be in the range of $42.3 to 67.5 million per year. The upper end of the range of estimated impacts assumes laboratory grade ventilation for aerosols, which we expect to be significantly more expensive than standard industrial fume hoods or spray booths (approximately $10,000 compared to $1,000 for each hood). For coatings, use of nPB is limited to a single facility that already performs workplace exposure monitoring, and thus, no new costs would be incurred. For aerosols and adhesives, we assumed the installation of fume hoods or spray booths, the use of personal protective equipment, and monitoring for 1.9 to 2.0 times per year on average. Using these assumptions, we calculated the cost of the use conditions in the proposed alternate approach at $18.0 to 24.0 million for adhesive users, and $24.3 to 43.5 million for aerosol users. The estimated cost of the use conditions does not consider that some users could choose to switch to other alternatives at a lower cost.
Estimated costs of the proposed regulation and proposed alternate approach are summarized in Table 13. For more detailed information, see section XIII.C. below and EPA's analysis in the docket (US EPA, 2006).
Table 13.--Estimated Costs of Regulatory Options EPA is Providing for Comment
Annual cost of Sector or end use
Requirements under Annual cost of Requirements under alternate proposed rule
proposed rule alternate approach approach
Aerosol Solvents.............. Cease use of nPB and $36.3 to 39.7 Achieve 20 ppm;
$24.3 to 43.5 switch to a
million.
exposure monitoring million. different ODS
one or two times per substitute.
year; Recordkeeping. Coatings...................... Decision applies to None............ Achieve 20 ppm;
None. use nPB in coatings
exposure monitoring, at facilities that,
one or two times per as of May 30, 2007,
year; recordkeeping. have provided EPA information demonstrating their ability to maintain acceptable workplace exposures. Adhesives..................... Cease use of nPB and $2.3 to 6.7 Achieve 20 ppm;
$18.0 to 24.0 switch to a
million.
exposure monitoring, million. different ODS
one or two times per substitute.
year; recordkeeping.
Total..................... ..................... $38.6 to 46.4 ..................... $42.3 to 67.5 million.
million.
[[Page 30197]]
-
How do the decisions for EPA's June 2003 proposal compare to those for this proposal?
Table 14 compares the acceptability determination and evidence cited in the June 2003 proposal and this proposal.
Table 14.--n-Propyl Bromide Acceptability Decision
Current proposed Proposed decision
2003 proposed rule rule--preferred proposal
Industrial End Use 1: Aerosol Solvents.
to a Use Condition (Limiting use to nPB formulations containing no more than 0.05% by weight isopropyl bromide; AEL of 25 ppm \1\ on 8-hr TWA recommended. Industrial End Use 2: Adhesives.
to a Use Condition (Limiting use to nPB formulations containing no more than 0.05% by weight isopropyl bromide; AEL of 25 ppm \1\ on 8-hr TWA recommended. Industrial End Use 3: Coatings.
to Use Conditions (Decision limited to coatings at facilities that, as of May 30, 2007, have provided EPA information demonstrating their ability to maintain acceptable workplace exposures.\2\
\1\ Proposed acceptable exposure limit of 25 ppm adjust upward from value of 18 ppm based upon nPB's effect on sperm motility from evaluation of the WIL 2001 Study ``An Inhalation Two-Generation Reproductive Toxicity Study of 1-Bromopropane in Rats.'' (a) ICF, 2001. ''Brief Discussion of the BMD Approach: Overview of its Purpose, Methods, Advantages, and Disadvantages.'' Prepared for U.S. EPA. (b) ICF, 2002a. ''Risk Screen for Use of N Propyl Bromide.'' Prepared for U.S. EPA, May, 2002. (c) ICF, 2002b. Comments on the NTP-Center for the Evaluation of Risks to Human Reproduction, Final Report on 1-Bromopropane. Cover Letter Dated 5/9/02. Also, evaluation of documents by CERHR (2002a, b), Doull and Rozman (2001), Rodricks (2002), Rozman and Doull (2002), SLR International (2001), and others. \2\ For purposes of this proposal, EPA is considering levels within the range of 17-30 ppm based on the following information on nPB's health effects for purposes of determining acceptability: estrous cycle length at 17 to 22 ppm, live litter size at 20 ppm, and sperm motility at 18 to 30 ppm from evaluation of the WIL 2001 Study ``An Inhalation Two-Generation Reproductive Toxicity Study of 1-Bromopropane in Rats'' and confirmed by comparison with other studies. Also, considers evaluation of documents by Stelljes and Wood (2004); TERA (2004); ICF, 2006a; ACGIH (2005); Rozman and Doull (2005); Stelljes (2005); and others.
-
How can I use nPB as safely as possible?
Below are actions that will help nPB users minimize exposure levels: All end uses
All users of nPB should wear appropriate personal protective equipment, including chemical goggles, flexible laminate protective gloves (e.g., Viton, Silvershield) and chemical-resistant clothing. Special care should be taken to avoid contact with the skin since nPB, like many halogenated solvents, can be absorbed through the skin. Refer to OSHA's standard for the selection and use of Personal Protective Equipment, 29 CFR 1910.132.
Limit worker exposure to solvents to minimize any potential adverse health effects. Workers should avoid staying for long periods of time in areas near where they have been using the solvent. Where possible, shorten the period during each day when a worker is exposed. Where respiratory protection is necessary to limit worker exposures, respirators must be selected and used in accordance with OSHA's Respiratory Protection standard, 29 CFR 1910.134.
Use less solvent, or use a different solvent, either alone or in a mixture with nPB.
Follow all recommended safety precautions specified in the manufacturer's MSDS.
Workers should receive safety training and education that includes potential health effects of exposure to nPB, covering information included on the appropriate MSDSs, as required by OSHA's Hazard Communication Standard (29 CFR 1910.1200).
Request a confidential consultation from your State government on all aspects of occupational safety and health. You can contact the appropriate state agency that participates in OSHA's consultation program. These contacts are on OSHA's web site at http://www.osha.gov/oshdir/consult.html. For further information on OSHA's
confidential consultancy program, visit OSHA's web page at http://www.osha.gov/html/consultation.html .
Use the employee exposure monitoring programs and product stewardship programs where offered by manufacturers and formulators of nPB-based products.
If the manufacturer or formulator of your nPB-based product does not have an exposure monitoring program, we recommend that you start your own exposure monitoring program, and/or request a confidential consultation from your State government. A medical monitoring program should be established for the early detection and prevention of acute and chronic effects of exposure to nPB. The workers' physician(s) should be given information about the adverse health effects of exposure to nPB and the workers' potential for exposure. Spray applications
For spray applications (e.g., aerosols), consider your available options, and if using nPB, use sufficient ventilation to reduce exposure to maintain acceptable exposure levels.
For ventilation, we recommend that you follow the design guidelines for ventilation in ACGIH's Industrial Ventilation: A Manual of Recommended Practice (ACGIH, 2002). In particular, the guidelines in Chapter 10.75 are appropriate for spray booths, and the
[[Page 30198]]
guidelines in Chapter 10.35 are appropriate for laboratory hoods.
The ACGIH Ventilation Manual recommends a minimum flow rate of 150 cubic feet per minute (cfm) for each sq-ft of opening for a small booth with at least 4 sq-ft of open face area. This equates to an average face velocity of 150 ft/min. For a large booth, the recommended face velocity is 100 ft/min for walk-in booths and 100 to 150 ft/min for a large spray booth where the operator works outside. In general, the opening should be kept as small as possible to accommodate the work-pieces, generally 12 inches wider and taller than the largest piece of work. If all spraying is not directed towards the back of the booth or the booth is too shallow for the size of the pieces being sprayed or if disruptive air currents are present at the face of the booth, a greater flow of air will be needed. We note that these steps are useful for reducing exposure to any industrial solvent, and not just nPB.
-
Statutory and Executive Order Reviews
-
Executive Order 12866: Regulatory Planning and Review
Under Executive Order (EO) 12866 (58 FR 51735, October 4, 1993), this action is a ``significant regulatory action.'' It raises novel legal or policy issues arising out of legal mandates, the President's priorities, or the principles set forth in the Executive Order. Accordingly, EPA submitted this action to the Office of Management and Budget (OMB) for review under EO 12866 and any changes made in response to OMB recommendations have been documented in the docket for this action.
In addition, EPA prepared an analysis of the potential costs and benefits associated with this action. This analysis is contained in the document ``Analysis of Economic Impacts of Proposed nPB Rule on Aerosols and Adhesives.'' A copy of the analysis is available in the docket for this action (Ref. EPA-HQ-OAR-2002-0064) and the analysis is briefly summarized here. EPA estimates the total costs of the proposed rule to between $38.6 and 46.4 million per year.
-
Paperwork Reduction Act
The information collection requirements in this proposed rule have been submitted for approval to the Office of Management and Budget (OMB) under the Paperwork Reduction Act, 44 U.S.C. 3501 et seq. The Information Collection Request (ICR) document prepared by EPA has been assigned EPA ICR number 2224.01.
If the provisions of this proposed rule become final (i.e., if the proposed regulatory language at the end of this document is finalized), there would be no new information collection burden. This proposed rule contains no new requirements for reporting or recordkeeping. OMB has previously approved the information collection requirements contained in the existing regulations in subpart G of 40 CFR part 82 under the provisions of the Paperwork Reduction Act, 44 U.S.C. 3501 et seq. and has assigned OMB control number 2060-0226 (EPA ICR No. 1596.06). This ICR included five types of respondent reporting and record-keeping activities pursuant to SNAP regulations: Submission of a SNAP petition, filing a SNAP/Toxic Substance Control Act (TSCA) Addendum, notification for test marketing activity, record-keeping for substitutes acceptable subject to use restrictions, and record-keeping for small volume uses.
However, if EPA were to finalize the proposed alternate approach described in section VII.A of this preamble, users of nPB would have an information collection burden from exposure monitoring and recordkeeping. Under the proposed alternate approach, users of nPB would be required to monitor worker exposure initially and periodically (usually every 6 months) and keep records of these exposure data at the facility for at least three years from the date the samples were taken. This data is necessary to ensure that users of nPB are meeting the regulatory use conditions. If the data indicates that the use condition is not being met, it could be used by EPA or citizens in an enforcement action against the facility. These data would be considered available to the public and would not be considered confidential.
The estimated burden of recordkeeping for the entire regulated community under the proposed alternate approach is as much as $7.0 million and 13,170 hours per year. The estimated recordkeeping burden for a typical user is $96 and 0.18 hours per worker per monitoring event. We estimate approximately 1.9 monitoring events per year per worker, assuming that roughly 90% of exposed workers must be monitored every six months and 10% must be monitored once annually. We estimate that up to 35,000 workers would be monitored for exposure to nPB. Costs under the proposed alternate approach include the annual cost of purchasing passive organic exposure monitoring badges, the annual cost of services for analyzing the resulting exposure, and the annual cost of reviewing and filing the data up to 2 times per year.
Burden means the total time, effort, or financial resources expended by persons to generate, maintain, retain, or disclose or provide information to or for a Federal agency. This includes the time needed to review instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting, validating, and verifying information, processing and maintaining information, and disclosing and providing information; adjust the existing ways to comply with any previously applicable instructions and requirements; train personnel to be able to respond to a collection of information; search data sources; complete and review the collection of information; and transmit or otherwise disclose the information.
An Agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB control number. The OMB control numbers for EPA's regulations are listed in 40 CFR part 9 and 48 CFR chapter 15.
To comment on the Agency's need for this information, the accuracy of the provided burden estimates, and any suggested methods for minimizing respondent burden, including through the use of automated collection techniques, EPA has established a public docket for this rule, which includes this ICR, under Docket ID number EPA-HQ-OAR-2002- 0064. Submit any comments related to the ICR for this proposed rule to EPA and OMB. See Addresses section at the beginning of this notice for where to submit comments to EPA. Send comments to OMB at the Office of Information and Regulatory Affairs, Office of Management and Budget, 725 17th St., NW., Washington, DC 20503, marked ``Attention: Desk Officer for EPA.'' Include the ICR number in any correspondence. Since OMB is required to make a decision concerning the ICR between 30 and 60 days after May 30, 2007, a comment to OMB is best assured of having its full effect if OMB receives it by June 29, 2007. The final rule will respond to any OMB or public comments on the information collection requirements contained in this proposal.
-
Regulatory Flexibility Act
The Regulatory Flexibility Act (RFA) generally requires an agency to prepare a regulatory flexibility analysis of any rule subject to notice and comment rulemaking requirements under the Administrative Procedure Act or any
[[Page 30199]]
other statute unless the agency certifies that the rule will not have a significant economic impact on a substantial number of small entities. Small entities include small businesses, small organizations, and small governmental jurisdictions. The RFA provides default definitions for each type of small entity. Small entities are defined as: (1) A small business as defined by the Small Business Administration's (SBA) regulations at 13 CFR 121.201; (2) a small governmental jurisdiction that is a government of a city, county, town, school district or special district with a population of less than 50,000; and (3) a small organization that is any not-for-profit enterprise which is independently owned and operated and is not dominant in its field. However, the RFA also authorizes an agency to use alternate definitions for each category of small entity, ``which are appropriate to the activities of the agency'' after proposing the alternate definition(s) in the Federal Register and taking comment. 5 U.S.C. 601(3)-(5). In addition, to establish an alternate small business definition, agencies must consult with SBA's Office of Advocacy.
EPA proposed an alternate definition for regulatory flexibility analyses under the RFA for rules related to the use of nPB as an alternative to ozone-depleting substances (ODS) in metals, precision, and electronics cleaning, adhesives, and aerosol solvents in the June 2003 NPRM (68 FR 33309, June 3, 2003). EPA established this final definition under section 601(3) of the RFA when we promulgated the final rule on the acceptable use of nPB in metals, precision, and electronics cleaning in the Rules and Regulations section of today's Federal Register. For purposes of assessing the economic impacts of this proposed rule on small entities, EPA defined ``small business'' as a small business with less than 500 employees, rather than use the individual SBA size standards for the numerous NAICS subsectors and codes. We believe that no small governments or small organizations are affected by this rule. EPA chose to use the alternate definition to simplify the economic analysis. This approach slightly reduced the number of small businesses included in our analysis and slightly increased the percentage of small businesses for whom the analysis indicated the use of nPB in accordance with this proposed rule may have an economically significant impact. Furthermore, this size standard was set by the Small Business Administration for all NAICS codes for businesses using nPB-based adhesives, one of the end uses that would be affected by this rule.
After considering the economic impacts of this proposed rule on small entities, I certify that this action will not have a significant economic impact on a substantial number of small entities. This rule proposes to list nPB as an unacceptable substitute for ODS in aerosols and adhesives. EPA has analyzed the economic impacts of switching from nPB to other alternative aerosol solvents or adhesives. EPA estimates that up to 3,380 small industrial end users currently use nPB in the end uses addressed by this proposed rule and thus could be subject to the regulatory impacts of this rule. This number includes approximately 3,100 users of nPB-based aerosol solvents, and 280 users of nPB-based adhesives. Considering the regulatory impacts on adhesive and aerosol users that must switch to other alternatives, we found that up to 258 (8%) of small businesses would experience impacts of 1% or greater of annual sales and no small businesses would experience impacts of 3% or greater of annual sales. Based on the relatively small number and low percentage of small businesses that would experience significant economic impacts, EPA concludes that this rule would not have a significant economic impact on a substantial number of small entities.
In the case of coatings uses, our understanding is that only a single facility, the Lake City Army Ammunition Plant, is currently using coatings with nPB as the carrier solvent, and this facility could continue to use nPB following its current practices. Therefore, we consider there to be no economic impact of this rule on coatings users and have not done further analysis for this end use.
Types of businesses that would be subject to this proposed rule include:
Manufacturers of computers and electronic equipment that clean with nPB cleaning solvents (NAICS subsector 334).
Manufacturers of appliances, electrical equipment, and components that require oil, grease, and solder flux to be cleaned off (NAICS subsection 335).
Manufacturers of transportation equipment, such as aerospace equipment that requires cleaning either in a tank or with aerosols, or aircraft seating, which is assembled using adhesives containing nPB as a carrier solvent; and ship or boat builders applying adhesives with nPB (NAICS subsector 336).
Manufacturers of furniture, including various kinds of furniture with cushions and countertops assembled using adhesives containing nPB as a carrier solvent (NAICS subsector 337).
Foam fabricators, who assemble foam cushions or sponges using adhesives containing nPB as a carrier solvent (NAICS code 326150).
In order to consider the resources that affected small businesses have available to operate and to respond to the proposed regulatory requirements, EPA compared the cost of meeting the proposed regulatory requirements to small businesses' annual sales. In our analysis for this proposed rule, we used the average value of shipments for the products manufactured by the end user as a proxy for sales or revenues, since these data are readily available from the U.S. Department of Commerce. The following tables display the average value of shipments for different sizes of business and different NAICS subsectors or codes in the affected industrial sectors. EPA then used data from these sources to determine the potential economic impacts of this proposed rule on small businesses.
Table 15.--Average Value of Shipments in NAICS Subsectors Using Aerosol Solvents, by Number of Employees at Business
Average value of shipments per business ($) by NAICS subsector code
Number of employees at business
335, electrical 334, computer equipment,
336, and electronic appliance, and transportation products
component mfg equipment
1 to 4 employees..........................................
345,007
315,772
412,460 5 to 9 employees..........................................
1,317,238
1,243,065
1,414,384 10 to 19 employees........................................
2,566,913
2,483,327
2,573,352
[[Page 30200]]
20 to 49 employees........................................
5,672,245
5,389,945
5,738,739 50 to 99 employees........................................
12,951,836
12,650,236
12,735,583 100 to 249 employees......................................
31,258,875
31,290,638
34,256,544 250 to 499 employees......................................
84,270,454
77,279,974
86,911,454 Avg. value ship small businesses in sub-sector............
8,261,788
9,539,205
11,029,561 Avg. value ship all businesses in subsector...............
20,810,094
13,417,905
45,029,773 Avg. value shipments subset small businesses using nPB....
11,246,045
12,066,562
13,422,547
Table 16.--Average Value of Shipments in NAICS Categories Using nPB as a Carrier Solvent in Adhesives, by Number of Employees at Business
Average value of shipments per small business ($) by NAICS sub sector
326150, Number of employees at business
337121,
337110, wood urethane and 336360, motor 337124, metal upholstered kitchen cabinet other foam vehicle seating household household and counter tops products (except and interior
furniture furniture
polystyrene)
trim
1 to 4 employees..............................................
234,345
156,833
496,318
425,863
187,950 5 to 9 employees..............................................
963,021
622,744
1,305,183
1,728,132
903,393 10 to 19 employees............................................
1,771,416
1,141,119
3,152,283
3,082,486
1,431,480 20 to 49 employees............................................
3,653,623
2,619,197
6,615,331
5,508,370
3,538,684 50 to 99 employees............................................
8,089,968
7,386,365
13,281,000
14,088,500
7,547,536 100 to 249 employees..........................................
17,502,175
17,151,091
31,524,872
44,310,286
19,821,719 250 to 499 employees..........................................
40,250,813
55,982,674
64,119,800 123,803,610
d(1) Avg. Small Businesses in Sub sector...........................
3,588,297
1,150,768
10,472,992
12,542,725
3,141,720 Avg. ALL Businesses in Sub sector.............................
5,490,101
1,475,602
11,110,822
44,808,573
5,239,747 Avg. Subset Small Businesses using nPB........................
11,519,540
5,999,622
18,950,068
12,019,847
20,401,301
\(1)\ ``d'' designates ``Data withheld to avoid disclosing data of individual companies; data are included in higher level totals.'' The average value of shipments for businesses estimates those values marked with ``d,'' and thus may be overestimated or underestimated.
This proposed rule would list nPB as unacceptable for use in adhesives and aerosols. The available alternatives identified include adhesive formulations based on water, methylene chloride, or flammable solvents such as acetone and aerosol formulations of flammable solvents, combustible solvents, blends of trans-dichloroethylene and HFEs or HFCs, and HCFC-225ca/cb. We considered various aspects of the cost of switching to other alternatives, including the cost of meeting OSHA requirements and the cost of the alternative adhesive. We specifically request public comment on the assumptions and costs used in EPA's analysis (US EPA, 2007).
We estimate that up to 9 small businesses using nPB-based adhesives, or roughly 3% of the 280 or so small businesses that use nPB-based adhesives, would experience a cost increase (i.e., an impact) of greater than 1.0% of annual sales, and no small businesses would experience an impact of greater than 3% of annual sales if this proposed rule became final. For small businesses using nPB-based aerosols, we estimate that approximately 249 would experience a cost increase of greater than 1.0% of annual sales. This equates to roughly 8% of the 3100 or so small businesses currently using nPB-based aerosol solvents. No small businesses using aerosols would experience an impact of greater than 3% of annual sales. Approximately eight percent of all 3380 or so small businesses choosing to use nPB in these end uses would experience an impact of greater than 1.0% of annual sales and no small businesses would experience an impact of greater than 3.0% of annual sales. Because of the small total number and small percentage of affected businesses that would experience an impact of greater than either 1.0% or 3.0% of annual sales, EPA does not consider this proposed rule to have a significant economic impact on a substantial number of small businesses.
We also analyzed the potential small business impacts of the proposed alternate approach. Under the proposed alternate approach, users would have to: (1) Meet an exposure level of 20 ppm on an eight- hour time-weighted average, (2) monitor workers' exposure to nPB using a personal breathing zone sampler on an eight-hour time-weighted average initially and periodically (every 6 months or longer, depending on the concentration during initial monitoring), and (3) keep records of the worker exposure data on site at the facility for at least three years from the date of the measurement. We assume that the cost of following the proposed alternate approach is the cost of installing ventilation for aerosols and adhesives or emission controls for solvent cleaning, the cost of using personal protective equipment, and the cost of monitoring worker exposure. Approximately 67 to 387 aerosol solvent users (2 to 13 percent), 25 to 54 adhesive users (9 to 19 percent), and 2.6 to 12.6 percent of all 3380 or so small businesses would experience impacts of greater than 1% of annual sales if they chose to use nPB subject to the proposed use conditions rather than switching to another ODS substitute.
[[Page 30201]]
Four to nine users of nPB-based adhesives, or less than 1% of all small businesses affected by this proposal, would experience impacts of 3% or greater of annual sales under the proposed alternate approach. Based on this analysis, the proposed alternate approach would not create a significant adverse economic impact on a substantial number of small entities.
Although this proposed rule would not have a significant economic impact on a substantial number of small entities if it became final, EPA nonetheless has tried to reduce the impact of this rule on small entities. Before selecting preferred the regulatory option in this proposed rule, we considered a number of regulatory options, such as:
Placing a narrowed use limit on the use of nPB in adhesives and aerosols that would allow its use only in those cases where alternatives are technically infeasible due to performance or safety issues. This would have required testing, recordkeeping, and some installation of capital equipment.
Requiring that when nPB is used in adhesives or aerosols, it must be used with local ventilation equipment and personal protective equipment. This would have required further installation of capital equipment, without necessarily protecting workers as thoroughly as a required acceptable exposure limit or requiring a switch to another alternative.
Prohibiting the use of nPB in all end uses.
Retaining the previously proposed requirement for a limit on iPB content in nPB formulations.
The costs of a number of these options are included in EPA's analysis (US EPA, 2006; U.S. EPA, 2007).
In developing our regulatory options, we considered information we learned from contacting small businesses using or selling nPB. EPA staff visited the site of a small business using nPB for cleaning electronics. We contacted several fabricators of foam cushions that have used adhesives containing nPB. We participated in meetings with a number of adhesive manufacturers and users of adhesives in furniture construction. We developed a fact sheet and updated our program Web site to inform small businesses about the proposed rule and to request their comments.
We continue to be interested in the potential impacts of the proposed rule on small entities and welcome comments on issues related to such impacts.
-
Unfunded Mandates Reform Act
Title II of the Unfunded Mandates Reform Act of 1995 (UMRA), Public Law 104-4, establishes requirements for Federal agencies to assess the effects of their regulatory actions on State, local, and tribal governments and the private sector. Under section 202 of the UMRA, EPA generally must prepare a written statement, including a cost-benefit analysis, for proposed and final rules with ``Federal mandates'' that may result in expenditures to State, local, and tribal governments, in the aggregate, or to the private sector, of $100 million or more in any one year. Before promulgating an EPA rule for which a written statement is needed, section 205 of the UMRA generally requires EPA to identify and consider a reasonable number of regulatory alternatives and adopt the least costly, most cost-effective or least burdensome alternative that achieves the objectives of the rule. The provisions of section 205 do not apply when they are inconsistent with applicable law. Moreover, section 205 allows EPA to adopt an alternative other than the least costly, most cost-effective or least burdensome alternative if the Administrator publishes with the final rule an explanation why that alternative was not adopted. Before EPA establishes any regulatory requirements that may significantly or uniquely affect small governments, including tribal governments, it must have developed under section 203 of the UMRA a small government agency plan. The plan must provide for notifying potentially affected small governments, enabling officials of affected small governments to have meaningful and timely input in the development of EPA regulatory proposals with significant Federal intergovernmental mandates, and informing, educating, and advising small governments on compliance with the regulatory requirements. EPA has determined that this rule does not contain a Federal mandate that may result in expenditures of $100 million or more for State, local, and tribal governments, in the aggregate, or the private sector in any one year. This proposed rule does not affect State, local, or tribal governments. The enforceable requirements of the rule for the private sector affect a number of end users in manufacturing. The estimated cost of the proposed requirements for the private sector is approximately $38.6 to 46.4 million per year, and the proposed alternate approach would cost the private sector approximately $ 42.3 to 67.5 million per year. Therefore, the impact of this rule on the private sector is less than $100 million per year. Thus, this rule is not subject to the requirements of sections 202 and 205 of the UMRA. EPA has determined that this rule contains no regulatory requirements that might significantly or uniquely affect small governments. This regulation applies directly to facilities that use these substances and not to governmental entities.
-
Executive Order 13132: Federalism
Executive Order 13132, entitled ``Federalism'' (64 FR 43255, August 10, 1999), requires EPA to develop an accountable process to ensure ``meaningful and timely input by State and local officials in the development of regulatory policies that have federalism implications.'' ``Policies that have federalism implications'' is defined in the Executive Order to include regulations that have ``substantial direct effects on the States, on the relationship between the National government and the States, or on the distribution of power and responsibilities among the various levels of government.''
This proposed rule does not have federalism implications. It will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government, as specified in Executive Order 13132. This regulation applies directly to facilities that use these substances and not to governmental entities. Thus, Executive Order 13132 does not apply to this rule.
-
Executive Order 13175: Consultation and Coordination With Indian Tribal Governments
Executive Order 13175, entitled ``Consultation and Coordination with Indian Tribal Governments'' (65 FR 67249, November 6, 2000), requires EPA to develop an accountable process to ensure ``meaningful and timely input by tribal officials in the development of regulatory policies that have tribal implications.'' ``Policies that have tribal implications'' is defined in the Executive Order to include regulations that have ``substantial direct effects on one or more Indian tribes, on the relationship between the Federal government and the Indian tribes, or on the distribution of power and responsibilities between the Federal government and Indian tribes.''
This proposed rule does not have tribal implications. It will not have substantial direct effects on tribal governments, on the relationship between the Federal government and Indian tribes, or on the distribution of power and responsibilities between the
[[Page 30202]]
Federal government and Indian tribes, as specified in Executive Order 13175.
This proposed rule would not significantly or uniquely affect the communities of Indian tribal governments, because this regulation applies directly to facilities that use these substances and not to governmental entities. Thus, Executive Order 13175 does not apply to this proposed rule.
-
Executive Order 13045: Protection of Children From Environmental Health and Safety Risks
Executive Order 13045: ``Protection of Children from Environmental Health Risks and Safety Risks'' (62 FR 19885, April 23, 1997) applies to any rule that: (1) Is determined to be ``economically significant'' as defined under Executive Order 12866, and (2) concerns an environmental health or safety risk that EPA has reason to believe may have a disproportionate effect on children. If the regulatory action meets both criteria, the Agency must evaluate the environmental health or safety effects of the planned rule on children, and explain why the planned regulation is preferable to other potentially effective and reasonably feasible alternatives considered by the Agency.
This proposed rule is not subject to the Executive Order because it is not economically significant as defined in Executive Order 12866, and because the Agency does not have reason to believe the environmental health or safety risks addressed by this action present a disproportionate risk to children. The exposure limits and acceptability listings in this proposed rule apply to the workplace. These are areas where we expect adults are more likely to be present than children, and thus, the agents do not put children at risk disproportionately.
The public is invited to submit or identify peer-reviewed studies and data, of which the agency may not be aware, that assessed results of early life exposure to nPB.
-
Executive Order 13211: Actions That Significantly Affect Energy Supply, Distribution, or Use
This rule is not a ``significant energy action'' as defined in Executive Order 13211, ``Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use'' (66 FR 28355 (May 22, 2001)) because it is not likely to have a significant adverse effect on the supply, distribution, or use of energy. This action would impact manufacturing of various metal, electronic, medical, and optical products cleaned with solvents containing nPB and products made with adhesives containing nPB. Further, we have concluded that this rule is not likely to have any adverse energy effects.
-
-
National Technology Transfer and Advancement Act
As noted in the proposed rule, Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (``NTTAA''), Public Law 104-113, section 12(d) (15 U.S.C. 272 note) directs EPA to use voluntary consensus standards in its regulatory activities unless to do so would be inconsistent with applicable law or otherwise impractical. Voluntary consensus standards are technical standards (e.g., materials specifications, test methods, sampling procedures, and business practices) that are developed or adopted by voluntary consensus standards bodies. The NTTAA directs EPA to provide Congress, through OMB, explanations when the Agency decides not to use available and applicable voluntary consensus standards.
This action does not involved technical standards. Therefore, EPA did not consider the use of any voluntary consensus standards. We note that the American Conference of Governmental Industrial Hygienists (ACGIH), although it sets voluntary standards, is not a voluntary consensus standards body. Therefore, use of an acceptable exposure limit from the ACGIH is not subject to the NTTAA.
-
References
The documents below are referenced in the preamble. All documents are located in the Air Docket at the address listed in section I.B.1 at the beginning of this document. Unless specified otherwise, all documents are available electronically through the Federal Docket Management System, Docket EPA-HQ-OAR-2002-0064. Some specific items are available only in hard copy in dockets A-2001-07 or A-92-42 (legacy docket numbers for SNAP nPB rule and for SNAP program and submissions). Numbers listed after the reference indicate the docket and item numbers.
Availability
Harper, 2005. Telephone call from M. Sheppard, EPA to Dr. S. Harper, ATK. Re: Availability of other methyl chloroform substitutes for the Lake City Army Ammunition Plant. October 11, 2005. (EPA-HQ-OAR-2002- 0064-0150) IRTA, 2000. Alternative Adhesive Technologies in the Foam Furniture and Bedding Industries: A Cleaner Technologies Substitution Assessment, Cost and Performance Evaluation. Michael Morris and Katy Wolf, Institute for Research and Technical Assistance. Prepared for the U.S. EPA Office of Pollution Prevention Technology, June 2000. (A-2001-07, II-D-70) Seilheimer, 2001. Telephone Log of April 4, 2001 call between Margaret Sheppard, EPA, and Bob Seilheimer, Imperial Adhesives. (A- 2001-07, II-B-5) Williams, 2005. Notes on conversation of Ed Williams, Technical Manager, LPS Laboratories, and Margaret Sheppard, EPA. November 3, 2005 (EPA-HQ-OAR-2002-0064-0198)
Impacts on the Atmosphere, Local Air Quality, and Other Environmental Impacts
Atmospheric and Environmental Research, Inc., 1995. Estimates of the Atmospheric Lifetime, Global Warming Potential and Ozone Depletion Potential of n-Propyl Bromide. Independent study prepared for Albemarle Corporation. (A-2001-07, II-D-17) ATSDR, 1994. Toxicological Profile For Acetone. Agency for Toxic Substances and Disease Registry. May, 1994. Available at http://www.atsdr.cdc.gov/toxprofiles/tp21-c5.pdf (EPA-HQ-OAR-2002-0064-
0118) ATSDR, 1996. Toxicological Profile For 1,2-Dichloroethene. Agency for Toxic Substances and Disease Registry. August, 1996. Available at http://www.atsdr.cdc.gov/toxprofiles/tp87-c5.pdf (EPA-HQ-OAR-
2002-0064-0113) ATSDR, 1997. Toxicological Profile For Trichloroethylene. Agency for Toxic Substances and Disease Registry. September, 1997. Available athttp://www.atsdr.cdc.gov/toxprofiles/tp19-c5.pdf (EPA-HQ-OAR-2002-
0064-0123) ATSDR, 2004. Draft Toxicological Profile For 1,1,1-Trichloroethane. Agency for Toxic Substances and Disease Registry. September, 2004. Updated draft for comment. Available at http://www.atsdr.cdc.gov/toxprofiles/tp70-c6.pdf (EPA-HQ-OAR-2002-0064-0132)
EDSTAC, 1998. Final Report of the Endocrine Disruptor Screening and Testing Advisory Committee. August, 1998. (EPA-HQ-OAR-2002-0064- 0136) Fisher Scientific, 2001. Material Safety Data Sheet for acetone. Updated March 19, 2001. Available at http://www.mhatt.aps.anl.gov/dohn/msds/acetone.html (EPA-HQ-OAR-2002-0064-0129)
Geiger et al., 1998. Geiger, D.L., Call, D.J., and Brooke, L.T. 1988. Acute Toxicities of Organic Chemicals to Fathead Minnows (Pimephales promelas), Vol. 4. In: Center for Lake Superior Environmental Stud., Univ. of Wisconsin-Superior, Superior, WI I:355. (Summarized in ICF, 2004a) HSDB, 2004. Hazardous Substances Databank File for 1-Bromopropane. Accessed 1/2004 from the World Wide Web at http://toxnet.nlm.nih.gov/cgi-bin/sis/
[[Page 30203]]
search/f?./temp/dLwM9e:1 (Summarized in ICF, 2004a) ICF, 2003a. ICF Consulting. Revised Evaluation of the Global Warming Potential for n-Propyl Bromide. (EPA-HQ-OAR-2002-0064-0164) ICF, 2004a. ICF Consulting. Memo to E. Birgfeld, EPA, re: nPB Aquatic Toxicity. January 19, 2004. (EPA-HQ-OAR-2002-0064-0177) ICF, 2006a. ICF Consulting. Risk Screen on Substitutes for Ozone- Depleting Substances for Adhesive, Aerosol Solvent, and Solvent Cleaning Applications. Proposed Substitute: n-Propyl Bromide. April 18, 2006. Attachments: A, Determination of an AEL; B, Derivation of an RfC; C, Evaluation of the Global Warming Potential; D, Occupational Exposure Analysis for Adhesive Applications; E, Occupational Exposure Analysis for Aerosol Solvent Applications; F, General Population Exposure Assessment for n-Propyl Bromide LaGrega, M., Buckingham, P., Evans, J., and Environmental Resources Management, 2001. Hazardous Waste Management. Second Edition. McGraw-Hill, New York, NY. 2001. (EPA-HQ-OAR-2002-0064-0112) Linnell, 2003. Comments from the Electronics Industry Alliance. (EPA-HQ-OAR-2002-0064 items -0043, -0044, and -0045) MOP 18, 2006. Report of the Eighteenth Meeting of the Parties to the Montreal Protocol on Substances that Deplete the Ozone Layer. November 16, 2006. (EPA-HQ-OAR-2002-0064-0163) NPS, 1997. Irwin, R.J., M. VanMouwerik, L. Stevens, M.S. Seese, and W. Basham. 1997. Environmental Contaminants Encyclopedia. National Park Service, Water Resources Division, Fort Collins, Colorado. (EPA-HQ-OAR-2002-0064-0086) Steminiski, 2003. July 27, 2003 Comment from J. Steminiski, Ph.D. (EPA-HQ-OAR-2002-0064-0035 and -0043) U.S. Economic Census, 2002a. General Summary: 2002. Subject Series. Report No. EC02-31SG-1, October, 2005. U.S. Census Bureau. (EPA-HQ- OAR-2002-0064-0133) U.S. Economic Census, 2002b. U.S. Economic Census for Island Areas, 2002. Report for Northern Marianas Islands, Rpt. No. IA02-00A-NMI, May, 2004. U.S. Census Bureau. (EPA-HQ-OAR-2002-0064-0091) U.S. Economic Census, 2002c. U.S. Economic Census for Island Areas, 2002. Report for Guam, Rpt. No. IA02-00A-GUAM, March, 2005. U.S. Census Bureau. (EPA-HQ-OAR-2002-0064-0102) U.S. Economic Census, 2002d. U.S. Economic Census for Island Areas, 2002. Report for Virgin Islands, Rpt. No. IA02-00A-VI , April, 2005. U.S. Census Bureau. (EPA-HQ-OAR-2002-0064-0131) U.S. Economic Census, 2002e. U.S. Economic Census for Island Areas, 2002. Report for American Samoa, Rpt. No. IA02-00A-AS, April, 2005. U.S. Census Bureau. (EPA-HQ-OAR-2002-0064-0103) U.S. Economic Census, 2002f. U.S. Economic Census for Island Areas, 2002. Report for Puerto Rico: Manufacturing, Rpt. No. IA02-00I-PRM, October, 2005. U.S. Census Bureau. (EPA-HQ-OAR-2002-0064-0107) U.S. EPA, 1980. Ambient Water Quality Criteria for Dichloroethylenes. EPA 440/5-80-041 October, 1980. Available at http://www.epa.gov/waterscience/pc/ambientwqc/dichloroethylenes80.pdfU.S. EPA, 1992. Hazard Assessment Guidelines for Listing Chemicals
on the Toxic Release Inventory, Revised Draft. Washington, DC: Office of Pollution, Prevention and Toxics. As referenced in ICF, 2004f. U.S. EPA, 1994a. Chemical Summary for Methyl Chloroform, prepared by Office of Pollution Prevention and Toxics, August, 1994. (EPA-HQ- OAR-2002-0064-0121) WMO, 2002: Scientific Assessment of Ozone Depletion: 2002, Global Ozone Research and Monitoring Project--Report No. 47, Geneva, 2003 Full report available online at http://esrl.noaa.gov/csd/assessments/ (A-2001-07, II-A-20)
Wuebbles, Donald J. 2002. ``The Effect of Short Atmospheric Lifetimes on Stratospheric Ozone.'' Written for Enviro Tech International, Inc. Department of Atmospheric Sciences, University of Illinois-Urbana. (EPA-HQ-OAR-2002-0064-0114)
Flammability and Fire Safety
BSOC, 2000. February 1, 2000 Tabulation of Flammability Studies on n-Propyl Bromide from the Brominated Solvents Committee, and other information on flammability of n-propyl bromide. (A-2001-07, II-D- 45) Miller, 2003. Albemarle Corporation comments-Flash Point Data for n- Propyl Bromide. (EPA-HQ-OAR-2002-0064-0040) Morford, 2003a. Enviro Tech International Comment re Section IV D Flammability with Exhibits (7/25/03) (EPA-HQ-OAR-2002-0064-0030) Morford, 2003b. Enviro Tech International Supporting Exhibits on Flammability (7/25/03) (EPA-HQ-OAR-2002-0064-0031) Morford, 2003c. Enviro Tech Int. Flammability of nPB & Comparison With Methylene Chloride-Additional Comments on Flammability (7/29/ 03) (EPA-HQ-OAR-2002-0064-0036) Shubkin, 2003. R. Shubkin, Poly Systems, EPA received 7/23/03 Re: Comment on Flammability of n-Propyl Bromide as Discussed in Proposed Rule Published in Federal Register (EPA-HQ-OAR-2002-0064-0025) Weiss Cohen, 2003. T. Weiss Cohen, Dead Sea Bromine Group, 7/31/2003 Comment to Federal Register Proposed Rules of June 3, 2003, on Protection of Stratospheric Ozone: Listing of Substitutes for Ozone- Depleting Substances--n-Propyl Bromide (EPA-HQ-OAR-2002-0064-0053)
Impact on human health; how did EPA assess impacts on human health?
ACGIH, 1991. Skin Notation Documentation for Methyl Chloride. Available online at http://www.acgih.org.
ACGIH, 2005. Documentation for Threshold Limit Value for 1- Bromopropane. 2005. Available online at http://www.acgih.org.
Albemarle, 2003. Product Description for Abzol[supreg] Cleaners. 2003. (EPA-HQ-OAR-2002-0064-0148) Beck and Caravati, 2003. Neurotoxicity associated with 1- bromopropane exposure. Utah Poison Control Center, University of Utah, Salt Lake City, UT. J Toxicology Clinical Toxicology 41(5):729. (Abstract from conference). 2003. (EPA-HQ-OAR-2002-0064- 0111) CERHR, 2002a. NTP-Center for the Evaluation of Risks to Human Reproduction Expert Panel Report on the Reproductive and Developmental Toxicity of 1-Bromopropane [nPB]. March 2002. (EPA-HQ- OAR-2002-0064-0096) CERHR, 2002b. NTP-Center for the Evaluation of Risks to Human Reproduction Expert Panel Report on the Reproductive and Developmental Toxicity of 2-Bromopropane [iPB]. March 2002. (EPA-HQ- OAR-2002-0064-0083) CERHR, 2003a. NTP-CERHR Monograph on the Potential Human Reproductive and Developmental Effects of 1-Bromopropane. October 2003. (EPA-HQ-OAR-2002-0064-0084) CERHR, 2003b. NTP-CERHR Monograph on the Potential Human Reproductive and Developmental Effects of 2-Bromopropane. October 2003. (EPA-HQ-OAR-2002-0064-0079) CERHR, 2004a. NTP-CERHR Expert Panel report on the reproductive and developmental toxicity of 1-bromopropane. Center for the Evaluation of Risks to Human Reproduction. Repro Toxicol. Vol. 18, pp. 157-188. 2004. (EPA-HQ-OAR-2002-0064-0096) CERHR, 2004b. NTP-CERHR Expert Panel report on the reproductive and developmental toxicity of 2-bromopropane. Boekelheide, et al. Repro Toxicol. Vol. 18, pp. 189-217. 2004. (EPA-HQ-OAR-2002-0064-0098) Chemtura, 2006. Material Safety Data Sheet for n-propyl bromide. April, 2006. (EPA-HQ-OAR-2002-0064-0151) ClinTrials, 1997a. A 28-Day Inhalation Study of a Vapor Formulation of ALBTA1 in the Albino Rat. Report No. 91189. Prepared by ClinTrials BioResearch Laboratories, Ltd., Senneville, Quebec, Canada. May 15, 1997. Sponsored by Albemarle Corporation, Baton Rouge, LA. (A-91-42, X-A-4) ClinTrials, 1997b. ALBTA1: A 13-Week Inhalation Study of a Vapor Formulation of ALBTA1 in the Albino Rat. Report No. 91190. Prepared by ClinTrials BioResearch Laboratories, Ltd., Senneville, Quebec, Canada. February 28, 1997. Sponsored by Albemarle Corporation, Baton Rouge, LA. (A-91-42, X-A-5)
[[Page 30204]]
Confidential submission, 1998. Airborne Exposure Assessment of 1- Bromopropane, 1998. (A-2001-07, II-D-89). Dunson et al, 2002. Dunson, D., Colombo, and B., Baird, D. Changes with age in the level and duration of fertility in the menstrual cycle. Human Reproduction, Vol. 17, No. 5, pp. 1399-1403, 2002. (EPA-HQ-OAR-2002-0064-0120) Elf Atochem, 1995. Micronucleus Test by Intraperitoneal Route in Mice. n-Propyl Bromide. Study No. 12122 MAS. Study Director, Brigitte Molinier. Study performed by Centre International de Toxoicologie, Misery, France, September 6, 1995. (A-91-42, X-A-9) Enviro Tech International, 2006. Material Safety Data Sheet for Ensolv (n-propyl bromide solvent) (EPA-HQ-OAR-0064-0143) Farr, 2003. Comment on proposed rule on n-propyl bromide from Craig Farr, Atofina. July 31, 2003. (EPA-HQ-OAR-2002-0064-0060) Fueta et al., 2002. Y. Fueta, K. Fukunaga, T. Ishidao, H. Hori. Hyperexcitability and changes in activities of Ca2+/calmodulin- dependent kinase II and mitogen-activated protein kinase in the hippocampus of rats exposed to 1-bromopropane. 2002. Life Sciences 72 (2002) 521-529. (EPA-HQ-OAR-2002-0064-0115) Fueta et al., 2004. Y. Fueta, T. Fukuda, T. Ishidao, H. Hori. Electrophysiology and immunohistochemistry in the hippocampal CA1 and the Dentate Gyrus of Rats Chronically exposed to 1-Bromopropane, a Substitute for Specific Chlorofluorocarbons. Neuroscience 124 (2004) 593-603. (EPA-HQ-OAR-2002-0064-0142) Furuhashi, et al., 2006. K. Furuhashi, J. Kitoh, J. Tsukamura, K. Maeda, H. Wang, W. Li, S. Ichihara, T. Nakajima, and G. Ichihara. Effects of exposure of rat dams to 1-bromopropane during pregnancy and lactation on growth and sexual maturation of their offspring. Toxicology 224 (2006) 219-228. Available online at http://www.sciencedirect.com .
Great Lakes Chemical Corporation, 2001. Letter from E. Stouder, Great Lakes Chemical Corporation, 2/20/01. (A-2001-07, II-D-80) HESIS, 2003. California Department of Health Services--HESIS 1- Bromopropane (n-Propyl Bromide) Health Hazard Alert. (EPA-HQ-OAR- 2002-0064-0039) Honma et al., 2003. Honma, T., Suda, M., Miyagawa, M. ``Inhalation of 1-bromopropane causes excitation in the central nervous system of male F344 rats.'' Neurotoxicology. 2003 Aug; 24 (4-5):563-75. (EPA- HQ-OAR-2002-0064-0138) Huntingdon Life Sciences, 2001. A Developmental Toxicity Study in Rat Via Whole Body Inhalation Exposure. (A-2001-07, II-D-27) ICF, 2002a. Risk Screen for Use of N-Propyl Bromide. ICF Consulting. Prepared for U.S. EPA, May, 2002. (EPA-HQ-OAR-2002-0064-0006 through -0012) ICF, 2003. ICF Consulting. General Population Exposure Assessment for N-Propyl Bromide. June 03, 2003. (EPA-HQ-OAR-2002-0064-0011) ICF, 2004b. ICF Consulting. External Expert Review Panel on N-Propyl Bromide. December 13, 2004. ICF, 2004c. ICF Consulting. ICF Consulting Review of the TERA Report. December 13, 2004. ICF, 2004d. ICF Consulting. Review of ACGIH's Proposed Threshold Limit Value for 1-Bromopropane. April 26, 2004. ICF, 2006a. Full citation given above in section on ``Impacts on the atmosphere, local air quality, and other environmental impacts'' ICF, 2006b. ICF Consulting. Revised Memorandum regarding RTI Metabolism Study on nPB. April, 2006. (EPA-HQ-OAR-2002-0064-0179) ICF, 2006c. ICF Consulting. Evaluation of Memorandum from Dr. M. Stelljes. April, 2006. Ichihara et al., 1998. Ichihara, M., Takeuchi, Y., Shibata, E., Kitoh, J., et al. Neurotoxicity of 1-Bromopropane. 1998. Translated by Albemarle Corporation. (A-91-42, X-A-33) Ichihara, G., Jong, X., Onizuka, J., et al., 1999. Histopathological changes of nervous system and reproductive organ and blood biochemical findings in rats exposed to 1-bromopropane. (Abstract only) Abstracts of the 72nd Annual Meeting of Japan Society for Occupational Health. May 1999. Tokyo. (A-2001-07, II-A-15) Ichihara G., Kitoh J., Yu, X., et al., 2000a. 1-Bromopropane, an alternative to ozone layer depleting solvents, is dose-dependently neurotoxic to rats in long-term inhalation exposure. Toxicol Sciences 55:116-123. (A-2001-07, II-A-8) Ichihara, G., Yu, X., Kitoh, J., et al. 2000b. Reproductive toxicity of 1-bromopropane, a newly introduced alternative to ozone layer depleting solvents, in male rats. Toxicol Sciences 54:416-423. (A- 2001-07, II-A-7) Ichihara G. et al., 2002. Neurological Disorders in Three Workers Exposed to 1-Bromopropane. J Occu. Health 44:1-7. (A-2001-07, II-D- 64) Ichihara et al., 2004a. G. Ichihara, W. Li, X. Ding, S. Peng, X. Yu, E. Shibata, T. Yamada, H. Wang, S. Itohara, S. Kanno, K. Sakai, H. Ito, K. Kanefusa, and Y. Takeuchi. A Survey on Exposure Level, Health Status, and Biomarkers in Workers Exposed to 1-Bromopropane. Am Jrnl of Ind Med 45:63-75 (2004) (EPA-HQ-OAR-2002-0064-0093) Ichihara et al., 2004b. Gaku Ichihara, Weihua Li, Eiji Shibata, Xuncheng Ding, Hailan Wang, Yideng Liang, Simeng Peng, Seiichiro Itohara, Michihiro Kamijima, Qiyuan Fan, Yunhui Zhang, Enhong Zhong, Xiaoyun Wu, William M. Valentine, and Yasuhiro Takeuchi. Neurological Abnormalities in Workers of 1-Bromopropane Factory. Env'l Health Perspectives, 30 June 2004. (EPA-HQ-OAR-2002-0064-0139) Ishidao et al., 2002. Ishidao, T., Kunugita, N., Fueta, Y., Arashidani, K., Hori, H. Effects of inhaled 1-bromopropane vapor on rat metabolism. Toxicol Lett. 2002 Aug 5; 134(1-3):237-43 (EPA-HQ- OAR-2002-0064-0125) Lake City Army Ammunition Plant, 2003. SNAP application for n-Propyl Bromide in coatings, T.J. Herman, ATK Alliant Lake City Small Caliber Ammunition Company, dated 7/8/2003. EPA Received 7/14/2003. (EPA-HQ-OAR-2002-0064-0029) Lake City Army Ammunition Plant, 2004. March 9, 2004 Industrial Hygiene Air Sampling Report for Normal Propyl Bromide Based Mouth Waterproofing in Manufacture of 5.56 mm Ammunition. S.A. Hawk. (EPA- HQ-OAR-2002-0064-0211) Majersik et al., 2004. Chronic Exposure to 1-Bromopropane Associated with Spastic Paraparesis and Distal Neuropathy: A Report of Six Foam Cushion Gluers. Poster paper from 129th Annual Meeting of the American Neurological Association, Toronto. October, 2004. (EPA-HQ- OAR-2002-0064-0219) Majersik et al, 2005. ``Spastic Paraparesis and Distal Neuropathy Associated with Chronic Exposure to 1BP,'' Presentation by Drs. J. Majersik, M. Caravati, and J. Steffens at the North American Congress of Clinical Toxicologists. September 14, 2005. (EPA-HQ-OAR- 2002-0064-0116) Miller, 2005. ``1-Bromopropane: A Private Neurological Practice Experience in 2000,'' Presentation by Dr. J.M. Miller, at the North American Congress of Clinical Toxicologists. September 14, 2005. (EPA-HQ-OAR-2002-0064-0216) Morford, 2003d. White Paper: ``EPA Is Unlawfully Regulating Occupational Exposures'' Attachment to public comments. (EPA-HQ-OAR- 2003-0064-0049) Morford, 2003e. Comment regarding proposed restriction on isopropyl bromide Richard Morford, Enviro Tech International. August 3, 2003. (EPA-HQ-OAR-2002-0064-0042) Morford, 2003f. Support for EPA Proposal to Approve n propyl bromide and Comments Pursuant to Section D. Flammability of Protection of Stratospheric Ozone: Listing of Substitutes for Ozone Depleting Substances--n-Propyl Bromide: Proposed Rule Federal Register Vol. 68 No. 106, June 3, 2003. Enviro Tech International, Inc. Comments Regarding Proposed Rule & Exhibit A Richard Morford, Enviro Tech International. August 3, 2003. (EPA-HQ-OAR-2002-0064-0047) Morford, 2003g. Enviro Tech International, Inc. Combined Exhibits to Comment 0047/Morford, 2003f on Proposed Rule Richard Morford, Enviro Tech International. August 3, 2003. (EPA-HQ-OAR-2002-0064-0048) Morford, 2003h. Initial Comments to Protection of Stratospheric Ozone: Listing of Substitutes for Ozone Depleting Substances--n- Propyl bromide: Proposed Rule Federal Register Vol. 68 No. 106, June 3, 2003. Richard Morford, Enviro Tech International. June
[[Page 30205]]
26, 2003. (EPA-HQ-OAR-2002-0064-0002) NAS, 1983. The National Academies of Science, Risk Assessment in the Federal Government: Managing the Process, 1983. Available online at http://newton.nap.edu/catalog/366.html (Executive summary in docket
as EPA-HQ-OAR-2002-0064-0108) Nemhauser, 2005. ``Bromopropane: A Health Hazard Evaluation Revisited'' Presentation by Dr. J. Nemhauser, U.S. Public Health Service, Centers for Disease Control & Presentation at the North American Congress of Clinical Toxicologists. September 14, 2005. (EPA-HQ-OAR-2002-0064-0105) NIOSH, 2002a. NIOSH Health Hazard Evaluation Report: HETA 98-0153-2883; Custom Products, Inc.; Mooresville, NC. National Institute for Occupational Safety and Health. November 2002. Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/1998-0153-2883.pdf. (EPA-HQ-OAR-2002-0064-0090)
NIOSH, 2002b. NIOSH Health Hazard Evaluation Report: HETA 2000-0410-2891; STN Cushion Company; Thomasville, NC. National Institute for Occupational Safety and Health. August 2002. Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/2000-410-2891.pdf. (A-2001-07, II-A-31)
NIOSH, 2003a. NIOSH Health Hazard Evaluation Report 99- 0260-2906 Marx Industries, Inc. Sawmills, NC. Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/1999-0260-2906.pdf. (EPA-
HQ-OAR-2002-0064-0094) NTP, 2003. Results of 13-week Inhalation Testing by the National Toxicology Program. Available at http://ntp-apps.niehs.nih.gov/ntp_tox/ index.cfm?fuseaction=ntpsearch.searchresults&searchterm=106-94-
5 OEHHA, 2006. State Of California Environmental Protection Agency, Office Of Environmental Health Hazard Assessment. Chemicals Known To The State To Cause Cancer Or Reproductive Toxicity. June 9, 2006. (EPA-HQ-OAR-2002-0064-0124) O'Malley, 2004. Letter from Nancy O'Malley, Toxicology Advisor, Albemarle Corporation to The Science Group of the American Conference of Governmental Industrial Hygienists. Comments on the draft Documentation for proposed TLV for 1-bromopropane (1-BP). July 30, 2004. (EPA-HQ-OAR-2002-0064-0128) Raymond and Ford, 2005. ``Clinical Case Presentations from a Foam Furniture Fabrication Plant in North Carolina,'' Presentation by Drs. Larry Raymond and Marsha Ford at the North American Congress of Clinical Toxicologists. September 14, 2005. (EPA-HQ-OAR-2002-0064- 0170) Risotto, 2003. Comments of the Halogenated Solvents Industry Alliance on nPB proposed rule. June, 2003. (EPA-HQ-OAR-2002-0064- 0050) Rodricks, 2002. October 21, 2002 remarks from Dr. J. Rodricks, Environ, to R. Morford, Enviro Tech International concerning derivation of an OEL for n-propyl bromide with cover letter to EPA from Enviro Tech International (A-2001-07, II-D-65) Rozman and Doull, 2002. ``Derivation of an Occupational Exposure Limit for n-Propyl Bromide Using an Improved Methodology'' App Occu. Env. Hyg. 17: 711-716 (A-2001-07, II-D-63) Rozman and Doull, 2005. Presentation by Drs. Rozman and Doull at the North American Congress of Clinical Toxicologists. September 14, 2005. (EPA-HQ-OAR-2002-0064-0126) RTI, 2005. Report on uptake and metabolism of 1-bromopropane in rats and mice. Research Triangle Institute report for the National Toxicology Program. June, 2005. (EPA-HQ-OAR-2002-0064-0077, -0080, - 0081, -0082, -0101, -0104, -0137, -0137.1) Ruckriegel, 2003. Comment on n-Propyl Bromide Recommended Workplace Exposure Level in Proposed Rule Published in Federal Register Vol. 68, No. 106, June 3, 2003. August 2, 2003 (EPA-HQ-OAR-2002-0064- 0055) Rusch and Bernhard, 2003. Comments on proposed regulation of n- propyl bromide from Steven Bernhardt and George Rusch, Honeywell. August 1, 2003. (EPA-HQ-OAR-2002-0064-0059) Rusch, 2003. Late comments on proposed regulation of n-propyl bromide from George Rusch, Honeywell. (EPA-HQ-OAR-2002-0064-0068) Sekiguchi S, Suda M, Zhai YL, Honma T., ``Effects of 1-bromopropane, 2-bromopropane, and 1,2-dichloropropane on the estrous cycle and ovulation in F344 rats.'' Toxicol Lett 2002 Jan 5;126(1):41-9 (A- 2001-07, II-D-39) SLR International, 2001. ``Inhalation Occupational Exposure Limit for n-Propyl Bromide.'' Prepared for Enviro Tech International, Inc. 2001. (A-2001-07, II-D-15) Smith, 2003. Comments on Protection of Stratospheric Ozone: Listing of Substitutes for Ozone-Depleting Substances--n-Propyl Bromide, FR Vol. 68, No. 106, June 3, 2003. R.L. Smith, Albemarle Corporation. July 23, 2003. (EPA-HQ-OAR-2002-0064-0067) Sohn et al., 2002. Sohn YK, Suh JS, Kim JW, Seo HH, Kim JY, Kim HY, Lee JY, Lee SB, Han JH, Lee YM, Lee JY. ``A histopathologic study of the nervous system after inhalation exposure of 1-bromopropane in rat.'' Toxicol Lett. 2002 May 28;131(3):195-201. (EPA-HQ-OAR-2002- 0064-0127) Stelljes, 2003. Comments from Dr. Marc Stelljes, SLR International, on proposed rule on n-propyl bromide. (HQ-EPA-OAR-2002-0064-0022) Stelljes and Wood, 2004. Stelljes, M., Wood, R. Development of an occupational exposure limit for n-propylbromide using benchmark dose methods. Regulatory Toxicology and Pharmacology 40 (2004) 136-150 (EPA-HQ-OAR-2002-0064-0087) Stelljes, ME, 2005. Mechanistic Hypothesis for n-Propylbromide and Ramifications for Occupational Exposure Limit in the United States. Technical Memorandum to EnviroTech International. 7 September, 2005. (EPA-HQ-OAR-2002-0064-0144) Stump, 2005. ``The Reproductive Toxicity of nPB in Rats,'' Presentation by Dr. Donald Stump at the North American Congress of Clinical Toxicologists. September 14, 2005. (EPA-HQ-OAR-2002-0064- 0076) Swanson, M.B., J.R. Geibig, and K.E. Kelly. 2002. Alternative Adhesives Technologies: Foam Furniture and Bedding Industries, Final Draft. Volume 2: Risk Screening and Comparison. Chapter 4: Exposure Assessment. Produced by the University of Tennessee Center for Clean Products and Clean Technologies under a grant from EPA's Design for the Environment Branch, Office of Pollution and Prevention and Toxics. June 2002. Available online at http://eerc.ra.utk.edu/ccpct/aap1.html .
TERA, 2004. Toxicological Excellence for Risk Assessment. Scientific Review of 1-Bromopropane Occupational Exposure Limit Derivations-- Preliminary Thoughts and Areas for Further Analysis. 2004. (EPA-HQ- OAR-2002-0064-0189) Toraason, M., Lynch, D.W., DeBorda, D.G., Singh, N., Krieg, E., Butler, M.A.,Toennis, C.A., Nemhauser, J.B., 2006. DNA damage in leukocytes of workers occupationally exposed to 1-bromopropane. Mutation Research 603 (2006) 1-14 (EPA-HQ-OAR-2002-0064-0130) U.S. EPA, 1991. Guidelines for Developmental Toxicity Risk Assessment. U.S. Environmental Protection Agency. (A-2001-07, II-A- 51) U.S. EPA, 1994b. U.S. Environmental Protection Agency (US EPA). 1994. Methods for derivation of inhalation reference concentrations and application of inhalation dosimetry. EPA/600/8-90/066F. Office of Health and Environmental Assessment, Washington, DC. 1994. (A- 2001-07, II-A-16) U.S. EPA, 1995a. The Use of the Benchmark Dose Approach in Health Risk Assessment. EPA/630-R-94-007. Risk Assessment Forum, Washington, DC. (A-2001-07, II-A-17) U.S. EPA, 1995b. SCREEN3 air dispersion model. (A-2001-07, II-A-53) U.S. EPA, 1996. Guidelines for Reproductive Toxicity Risk Assessment. U.S. Environmental Protection Agency, Risk Assessment Forum, Washington, DC, 630/R-96/009, 1996. (EPA-HQ-OAR-2002-0064- 0109) Wang et al., 2003. H. Wang, G. Ichihara, H. Ito, K. Kato, J. Kitoh, T. Yamada, X. Yu, S. Tsuboi, Y. Moriyama, and Y. Takeuchi. 2003. ``Dose-Dependant Biochemical Changes in RateCentral Nervous System after 12-Week Exposure to 1-Bromopropane'' NeuroToxicology 24: 199- 206 (EPA-HQ-OAR-2002-0064-0088) Werner, 2003. Comments from 3M on nPB proposed rule. (EPA-HQ-OAR- 2002-0064-0058).
[[Page 30206]]
WIL, 2001. WIL Research Laboratories. ``An inhalation two-generation reproductive toxicity study of 1-bromopropane in rats.'' Sponsored by the Brominated Solvent Consortium. May 24, 2001. (A-2001-07, II- D-10) Yamada T. et al., 2003. Exposure to 1-Bromopropane Causes Ovarian Dysfunction in Rats. Toxicol Sci 71:96-103 (EPA-HQ-OAR-2002-0064- 0097)
Listings for Each End Use
Beck and Caravati, 2003. Full citation above for ``Human Health'' section. Calhoun County, 2005. Summary of Court Case against Franklin Technologies and Mid-South Adhesive Company in Calhoun County, MS. (EPA-HQ-OAR-2002-0064-0217) Collatz, 2003. Comment entitled ``Addition of n-Propyl-Bromide to the Significant New Alternatives Policy (SNAP) List'' submitted by Mark Collatz, Director of Government Relations, The Adhesive and Sealant Council, Inc. 04-Aug-2003. (EPA-HQ-OAR-2002-0064-0066) Confidential submission, 1998. Full citation above in ``Human Health'' section. CSMA, 1998. Letter with attachments from J. DiFazio, Chemical Specialties Manufacturers Association to C. Newberg, EPA Re: Maintaining the Current Exemption under Section 610 of the Clean Air Act for Use of HCFC-141b in Electronic Cleaning and Aircraft Maintenance. September 10, 1998. (EPA-HQ-OAR-2002-0064-0153) Harper, 2005. Full citation above for ``Availability'' section. ICF, 2006a. Full citation above for section on ``Impacts on the atmosphere, local air quality, and other environmental impacts''. Lake City Army Ammunition Plant, 2004. Full citation above in ``Human Health''section. Linnell, 2003. Comments from the Electronics Industry Alliance. (IV- D-25/EPA-HQ-OAR-2002-0064 items -0043, -0044, and -0045) Majersik et al., 2004. Full citation above for ``Human Health'' section. Majersik et al, 2005. Full citation above for ``Human Health'' section. Miller, 2005. Full citation above for ``Human Health'' section. NIOSH, 2000a. U.S. Dept. of Health and Human Services, Letter to Marx Industries, Inc., February 1, 2000. Re: results of nPB exposure assessment survey conducted Nov. 16-17, 1999. (A-2001-07, II-D-7) NIOSH, 2000b. U.S. Dept. of Health and Human Services, Letter to Custom Products Inc., December 21, 2000. Re: results of nPB exposure assessment survey conducted Nov. 16, 2000. (HHE Report 98-0153) (A- 2001-07, II-D-8) NIOSH, 2001. U.S. Dept. of Health and Human Services, Letter to STN Cushion Company, March 7, 2001. Re: Results of nPB exposure assessment survey conducted November 14, 2000. (A-2001-07, II-D-9) NIOSH, 2002a. Full citation above in ``Human Health'' section. NIOSH, 2002b. Full citation above in ``Human Health'' section. NIOSH, 2003a. NIOSH Health Hazard Evaluation Report 99- 0260-2906 Marx Industries, Inc. Sawmills, NC Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/1999-0260-2906.pdf. (EPA-
HQ-OAR-2002-0064-0094) Raymond and Ford, 2005. Full citation above for ``Human Health'' section. U.S. EPA, 2004. U.S. EPA Solvent Market Report: The U.S. Solvent Cleaning Industry and the Transition to Non Ozone Depleting Substances. Prepared for U.S. Environmental Protection Agency, Significant New Alternatives Policy (SNAP) Program by ICF Consulting. September 2004. (EPA-HQ-OAR-2002-0064-0106) Werner, 2003. Full citation above for ``Human Health'' section. Williams, 2005. Full citation above for ``Availability'' section.
What other options did EPA consider?
ACGIH, 2002. Industrial Ventilation: A Manual of Recommended Practice 23rd Edition. American Conference of Governmental Industrial Hygienists, Cincinnati, Ohio Available online at http://www.acgih.org .
CSMA, 1999. Full citation above for ``Decisions for Each Sector and End Use'' section. Ensolv, 2006. Material Safety Data Sheet for Ensolv Solvents. Enviro Tech International. February, 2006. (EPA-HQ-OAR-2002-0064-0143) ERG, 2004. Analysis of Health and Environmental Impacts of ODS Substitutes--Evaluating the need to set a short-term exposure or ceiling limit for n-propyl bromide. ERG. June 8, 2004. ICF, 2006a. Full citation above for section on ``Impacts on the atmosphere, local air quality, and other environmental impacts''. Lake City Army Ammunition Plant, 2004. Full citation above for ``Decisions for Each Sector and End Use'' section. Linnell, 2003. Full citation above for ``Ozone Depletion Potential and Other Environmental Impacts'' section. Micro Care, 2006. Web page for Micro Care Corporation on the Trigger GripTMDispensing System. URL at http://www.microcare.com/products/PDF/PS-05T_G.html , last update January
19, 2006. Also see http://www.microcare.com/images/PDF-CSP-Allied%20Worker%20Exposures.pdf .
NIOSH, 2000a. U.S. Dept. of Health and Human Services, Letter to Marx Industries, Inc., February 1, 2000. Re: Results of nPB exposure assessment survey conducted Nov. 16-17, 1999. (A-2001-07, II-D-7) NIOSH, 2002a. NIOSH Health Hazard Evaluation Report: HETA 98-0153-2883; Custom Products, Inc.; Mooresville, NC. National Institute for Occupational Safety and Health. November 2002. Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/1998-0153-2883.pdf. (EPA-HQ-OAR-2002-0064-0093)
NIOSH. 2002b. NIOSH Health Hazard Evaluation Report: HETA 2000-0410-2891; STN Cushion Company; Thomasville, NC. National Institute for Occupational Safety and Health. August 2002. Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/2000-0410-2891.pdf. (A-2001-07, II-A-31)
NIOSH, 2003a. NIOSH Health Hazard Evaluation Report 99- 0260-2906 Marx Industries, Inc. Sawmills, NC Available online at http://www.cdc.gov/niosh/hhe/reports/pdfs/1999-0260-2906.pdf. (EPA-
HQ-OAR-2002-0064-0094) NIOSH, 2003b. Method 1025 for 1- and 2-Bromopropane. NIOSH Manual of Analytical Methods, 4th Edition, March 15, 2003. (EPA-HQ-OAR-2002- 0064-0173) NIOSH, 2003c. Method 1003 for Halogenated Hydrocarbons. NIOSH Manual of Analytical Methods, 4th Edition, March 15, 2003. (EPA-HQ-OAR- 2002-0064-0134) Williams, 2005. Full citation above for ``Availability'' section.
What are the anticipated costs of this regulation to the regulated community?
U.S. EPA, 2006. Analysis of Economic Impacts of nPB Rulemaking. 2006.
Comparison of EPA's June 2003 Proposal and This Proposal
ACGIH, 2005. Full citation above for ``Human Health'' section. CERHR, 2002a. Full citation above for ``Human Health'' section. CERHR, 2002b. Full citation above for ``Human Health'' section. Doull and Rozman, 2001. Derivation of an Occupational Exposure Limit for n-Propyl Bromide, prepared by John Doull, PhD., M.D., and Karl K. Rozman, PhD., D.A.B.T. submitted by Envirotech International, Inc. (A-2001-07, II-D-14) ICF, 2001. Brief Discussion of the BMD Approach: Overview of its Purpose, Methods, Advantages, and Disadvantages. Prepared for U.S. EPA. (A-2001-07, II-A-52) ICF, 2002a. Full citation above for ``Human Health'' section. ICF, 2002b. Comments on the NTP-Center for the Evaluation of Risks to Human Reproduction, Final Report on 1-Bromopropane. Cover Letter Dated 5/9/02. (EPA-HQ-OAR-2002-0064-0013) ICF, 2006a. Full citation above for section on ``Impacts on the atmosphere, local air quality, and other environmental impacts''. Rodricks, 2002. Full citation above for ``Human Health'' section. Rozman and Doull, 2002. Full citation above for ``Human Health'' section. Rozman and Doull, 2005. Full citation above for ``Human Health'' section. SLR International, 2001. Full citation above for ``Human Health'' section. Stelljes and Wood, 2004. Full citation above for ``Human Health'' section. Stelljes, ME. 2005. Full citation above for ``Human Health'' section.
[[Page 30207]]
TERA, 2004. Full citation above for ``Human Health'' section. WIL, 2001. Full citation above for ``Human Health'' section.
How can I use nPB as safely as possible?
ACGIH, 2002. Full citation above for ``What other options did EPA consider'' section.
Statutory and Executive Order Reviews
U.S. EPA, 2006. Analysis of Economic Impacts of nPB Rulemaking. 2006. U.S. EPA, 2007. Analysis of Economic Impacts of Proposed nPB Rule for Aerosols and Adhesives. 2007.
List of Subjects in 40 CFR Part 82
Environmental protection, Administrative practice and procedure, Air pollution control, Reporting and recordkeeping requirements.
Dated: May 15, 2007. Stephen L. Johnson, Administrator.
For the reasons set out in the preamble, 40 CFR part 82 is proposed to be amended as follows:
PART 82--PROTECTION OF STRATOSPHERIC OZONE
1. The authority citation for Part 82 continues to read as follows:
Authority: 42 U.S.C. 7414, 7601, 7671--7671q.
2. Subpart G is amended by adding Appendix S to read as follows:
Subpart G--Significant New Alternatives Policy Program
* * * * *
Appendix S to Subpart G--Substitutes Subject to Use Restrictions and Unacceptable Substitutes
Listed in the May 30, 2007 final rule.
Aerosols--Unacceptable Substitutes
End use
Substitute
Decision
Further information
Aerosol solvents.................. n-propyl bromide (nPB) as Unacceptable......... EPA finds unacceptable a substitute for CFC-113,
risks to human health in HCFC-141b, and methyl
this end use compared to chloroform.
other available alternatives. nPB, also known as 1-bromopropane, is Number 106-94-5 in the CAS Registry.
Adhesives, Coatings, and Inks--Substitutes That Are Acceptable Subject to Use Conditions
End use
Substitute
Decision
Use conditions
Further information
Coatings
n-propyl bromide Acceptable subject Use is limited to
EPA recommends the use (nPB) as a
to use conditions. coatings at facilities of personal protective substitute for
that, as of May 30, equipment, including methyl chloroform,
2007, have provided chemical goggles, CFC-113, and HCFC-
EPA information
flexible laminate 141b.
demonstrating
protective gloves and acceptable workplace chemical-resistant exposures.
clothing. EPA expects that all users of nPB would comply with any final Permissible Exposure Limit that the Occupational Safety and Health Administration issues in the future under 42 U.S.C. 7610(a). nPB, also known as 1- brompropane, is Number 106-94-5 in the CAS Registry.
As of May 30, 2007, the Lake City Army Ammunition Plant is the only facility using nPB in coatings that has provided information to EPA that meets this condition.
Adhesives, Coatings, and Inks--Unacceptable Substitutes
End use
Substitute
Decision
Further information
Adhesives......................... n-propyl bromide (nPB) as Unacceptable......... EPA finds unacceptable a substitute for CFC-113,
risks to human health in HCFC-141b, and methyl
this end use compared to chloroform.
other available alternatives. nPB, also known as 1-bromopropane, is Number 106-94-5 in the CAS Registry.
[FR Doc. E7-9706 Filed 5-29-07; 8:45 am]
BILLING CODE 6560-50-P
