Airworthiness Directives:

Federal Register: January 5, 2011 (Volume 76, Number 3)

Proposed Rules

Page 482-485

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

DOCID:fr05ja11-22

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration 14 CFR Part 39

Docket No. FAA-2010-1304; Directorate Identifier 2010-NM-254-AD

RIN 2120-AA64

Airworthiness Directives; Fokker Services B.V. Model F.28 Mark 1000, 2000, 3000, and 4000 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation

Page 483

product. The MCAI describes the unsafe condition as:

* * * under certain conditions, an ignition source may develop in the wing tank vapour space, due to insufficient clearance between the wiring along the Fuel Quantity Tank Units (FQTU's) and the local reinforcing structure around the upper skin cut-out.

This condition, if not corrected, in combination with flammable fuel vapours, could result in a wing tank explosion and consequent loss of the aeroplane.

* * * * *

The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by February 22, 2011.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact

Fokker Services B.V., Technical Services Dept., P.O. Box 231, 2150 AE

Nieuw-Vennep, the Netherlands; telephone +31 (0)252-627-350; fax +31

(0)252-627-211; e-mail technicalservices.fokkerservices@stork.com;

Internet http://www.myfokkerfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane

Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer,

International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2010-1304;

Directorate Identifier 2010-NM-254-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We will post all comments we receive, without change, to http:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

The European Aviation Safety Agency (EASA), which is the Technical

Agent for the Member States of the European Community, has issued EASA

Airworthiness Directive 2010-0156, dated August 3, 2010 (referred to after this as ``the MCAI''), to correct an unsafe condition for the specified products. The MCAI states:

* * * The FAA has published Special Federal Aviation Regulation

(SFAR) 88, and the [Joint Aviation Authorities] JAA has published

Interim Policy INT/POL/25/12. The design review conducted by Fokker

Services on the Fokker F28 type design in response to these regulations revealed that, under certain conditions, an ignition source may develop in the wing tank vapour space, due to insufficient clearance between the wiring along the Fuel Quantity

Tank Units (FQTU's) and the local reinforcing structure around the upper skin cut-out.

This condition, if not corrected, in combination with flammable fuel vapours, could result in a wing tank explosion and consequent loss of the aeroplane.

For the reasons described above, this AD requires a one-time

detailed

inspection to investigate if a clearance of 3 mm (0.12 inch) or more is available between the FQTU probes wiring and the surrounding reinforcement structure of the wing upper skin and corrective rework actions, depending on findings.

You may obtain further information by examining the MCAI in the AD docket.

The FAA has examined the underlying safety issues involved in fuel tank explosions on several large transport airplanes, including the adequacy of existing regulations, the service history of airplanes subject to those regulations, and existing maintenance practices for fuel tank systems. As a result of those findings, we issued a regulation titled ``Transport Airplane Fuel Tank System Design Review,

Flammability Reduction and Maintenance and Inspection Requirements''

(66 FR 23086, May 7, 2001). In addition to new airworthiness standards for transport airplanes and new maintenance requirements, this rule included Special Federal Aviation Regulation No. 88 (``SFAR 88,''

Amendment 21-78, and subsequent Amendments 21-82 and 21-83).

Among other actions, SFAR 88 requires certain type design (i.e., type certificate (TC) and supplemental type certificate (STC)) holders to substantiate that their fuel tank systems can prevent ignition sources in the fuel tanks. This requirement applies to type design holders for large turbine-powered transport airplanes and for subsequent modifications to those airplanes. It requires them to perform design reviews and to develop design changes and maintenance procedures if their designs do not meet the new fuel tank safety standards. As explained in the preamble to the rule, we intended to adopt airworthiness directives to mandate any changes found necessary to address unsafe conditions identified as a result of these reviews.

In evaluating these design reviews, we have established four criteria intended to define the unsafe conditions associated with fuel tank systems that require corrective actions. The percentage of operating time during which fuel tanks are exposed to flammable conditions is one of these criteria. The other three criteria address the failure types under evaluation: Single failures, single failures in combination with a latent condition(s), and in-service failure experience. For all four criteria, the evaluations included consideration of previous actions taken that may mitigate the need for further action.

The Joint Aviation Authorities (JAA) has issued a regulation that is similar to SFAR 88. (The JAA is an associated body of the European

Civil Aviation Conference (ECAC) representing the civil aviation regulatory authorities of a number of European States who have agreed to co-operate in developing and implementing common safety regulatory standards and procedures.) Under this regulation, the JAA stated that all members of the ECAC that hold type certificates for transport category

Page 484

airplanes are required to conduct a design review against explosion risks.

We have determined that the actions identified in this AD are necessary to reduce the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.

Relevant Service Information

Fokker Services B.V. has issued Fokker Service Bulletin SBF28-57- 097, Revision 1, dated June 10, 2010. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a Note within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 2 products of U.S. registry. We also estimate that it would take about 6 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of the proposed

AD on U.S. operators to be $1,020, or $510 per product.

In addition, we estimate that any necessary follow-on actions would take about 21 work-hours and require parts costing $0, for a cost of

$1,785 per product. We have no way of determining the number of products that may need these actions.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation

Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in

``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation: 1. Is not a ``significant regulatory action'' under Executive Order 12866; 2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the

Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended] 2. The FAA amends Sec. 39.13 by adding the following new AD:

Fokker Services B.V.: Docket No. FAA-2010-1304; Directorate

Identifier 2010-NM-254-AD.

Comments Due Date

(a) We must receive comments by February 22, 2011.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Fokker Services B.V. Model F.28 Mark 1000, 2000, 3000, and 4000 airplanes, certificated in any category, all serial numbers.

Subject

(d) Air Transport Association (ATA) of America Code 57: Wings.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

* * * under certain conditions, an ignition source may develop in the wing tank vapour space, due to insufficient clearance between the wiring along the Fuel Quantity Tank Units (FQTU's) and the local reinforcing structure around the upper skin cut-out.

This condition, if not corrected, in combination with flammable fuel vapours, could result in a wing tank explosion and consequent loss of the aeroplane.

* * * * *

Compliance

(f) You are responsible for having the actions required by this

AD performed within the compliance times specified, unless the actions have already been done.

Detailed Inspection and Corrective Actions

(g) At the next scheduled opening of the fuel tanks, but not later than 84 months after the effective date of this AD, do a detailed inspection for minimum clearance of the gap between the

FQTU wiring harness and the outer wing FQTU hole reinforcement structure, in accordance with the Accomplishment Instructions of

Fokker Service Bulletin SBF28-57-097, Revision 1, dated June 10, 2010.

(h) If during the inspection required by paragraph (g) of this

AD, the minimum clearance is found to be insufficient, as defined in the Accomplishment Instructions of Fokker Service Bulletin SBF28-57- 097, Revision 1, dated June 10, 2010, before further flight, rework the surrounding structure to remove the possibility of an ignition source, in accordance with the

Page 485

Accomplishment Instructions of Fokker Service Bulletin SBF28-57-097,

Revision 1, dated June 10, 2010.

Credit for Actions Accomplished in Accordance With Previous Service

Information

(i) Inspections accomplished before the effective date of this

AD according to Fokker Service Bulletin SBF28-57-097, dated May 6, 2010, are considered acceptable for compliance with the requirements of paragraph (g) of this AD.

FAA AD Differences

Note 1: This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(j) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager,

International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tom

Rodriguez, Aerospace Engineer, International Branch, ANM-116,

Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton,

Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149.

Information may be e-mailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov.

Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office.

The AMOC approval letter must specifically reference this AD.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: A Federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the

Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave.,

SW., Washington, DC 20591, Attn: Information Collection Clearance

Officer, AES-200.

Related Information

(k) Refer to MCAI European Aviation Safety Agency (EASA)

Airworthiness Directive 2010-0156, dated August 3, 2010; and Fokker

Service Bulletin SBF28-57-097, Revision 1, dated June 10, 2010; for related information.

Issued in Renton, Washington, on December 28, 2010.

Jeffrey E. Duven,

Acting Manager, Transport Airplane Directorate, Aircraft Certification

Service.

FR Doc. 2010-33337 Filed 1-4-11; 8:45 am

BILLING CODE 4910-13-P