Airworthiness directives: Groupe Aerospatiale,
[Federal Register: August 29, 2001 (Volume 66, Number 168)]
[Proposed Rules]
[Page 45648-45651]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr29au01-32]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 2001-CE-01-AD]
RIN 2120-AA64
Airworthiness Directives; SOCATA--Groupe Aerospatiale Models TB 9, TB 10, TB 20, TB 21, and TB 200 Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: This document proposes to adopt a new airworthiness directive (AD) that would apply to all SOCATA--Groupe Aerospatiale (SOCATA) Models TB 9, TB 10, TB 20, TB 21, and TB 200 airplanes. The proposed AD would require you to repetitively inspect the lower rudder hinge fitting for cracks. The proposed AD would also require you to repair any crack found in accordance with a repair scheme obtained from the manufacturer through the Federal Aviation Administration (FAA). The proposed AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for France. The actions specified by the proposed AD are intended to detect and correct fatigue cracks in the lower rudder hinge fitting. This condition could cause the lower rudder to detach from the control linkage with consequent loss of control of the airplane.
DATES: The FAA must receive any comments on this proposed rule on or before September 28, 2001.
ADDRESSES: Submit comments in triplicate to FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2001-CE-01-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Comments may be inspected at this location between 8 a.m. and 4 p.m., Monday through Friday, holidays excepted.
Service information that applies to the proposed AD may be obtained from SOCATA Groupe AEROSPATIALE, Customer Support, Aerodrome Tarbes- Ossun-Lourdes, BP 930--F65009 Tarbes Cedex, France; telephone: (33)
[[Page 45649]]
(0)5.62.41.73.00; facsimile: (33) (0)5.62.41.76.54; or the Product Support Manager, SOCATA--Groupe AEROSPATIALE, North Perry Airport, 7501 Pembroke Road, Pembroke Pines, Florida 33023; telephone: (954) 894- 1160; facsimile: (954) 964-4191. This information also may be examined at the Rules Docket at the address above.
FOR FURTHER INFORMATION CONTACT: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; facsimile: (816) 329-4090.
SUPPLEMENTARY INFORMATION:
Comments Invited
How do I comment on the proposed AD? The FAA invites comments on this proposed rule. You may submit whatever written data, views, or arguments you choose. You need to include the rule's docket number and submit your comments in triplicate to the address specified under the caption ADDRESSES. The FAA will consider all comments received on or before the closing date. We may amend the proposed rule in light of comments received. Factual information that supports your ideas and suggestions is extremely helpful in evaluating the effectiveness of the proposed AD action and determining whether we need to take additional rulemaking action.
Are there any specific portions of the proposed AD I should pay attention to? The FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of the proposed rule that might suggest a need to modify the rule. You may examine all comments we receive before and after the closing date of the rule in the Rules Docket. We will file a report in the Rules Docket that summarizes each FAA contact with the public that concerns the substantive parts of the proposed AD.
We are re-examining the writing style we currently use in regulatory documents, in response to the Presidential memorandum of June 1, 1998. That memorandum requires federal agencies to communicate more clearly with the public. We are interested in your comments on whether the style of this document is clear, and any other suggestions you might have to improve the clarity of FAA communications that affect you. You can get more information about the Presidential memorandum and the plain language initiative at http://www.plainlanguage.gov.
How can I be sure FAA receives my comment? If you want us to acknowledge the receipt of your comments, you must include a self- addressed, stamped postcard. On the postcard, write ``Comments to Docket No. 2001-CE-01-AD.'' We will date stamp and mail the postcard back to you.
Discussion
What events have caused this proposed AD? The Direction Generale de l'Aviation Civile (DGAC), which is the airworthiness authority for France, recently notified FAA that an unsafe condition may exist on all SOCATA Models TB 9, TB 10, TB 20, TB 21, and TB 200 airplanes. The DGAC reports an occurrence of the lower rudder separating from the control linkage on a Model TB 9 airplane. A break in the lower rudder hinge fitting caused this problem and was found during a scheduled inspection on the airplane with more than 6,000 hours time-in-service (TIS). The DGAC reports that material fatigue caused cracks in the lower rudder hinge fitting.
What are the consequences if the condition is not corrected? If this condition is not detected and corrected, the lower rudder could detach from the control linkage with consequent loss of control of the airplane.
Is there service information that applies to this subject? SOCATA has issued Service Bulletin SB 10-114 55, dated September 2000.
What are the provisions of this service bulletin? The service bulletin includes procedures for inspecting the lower rudder hinge fitting for cracks. This document also includes information about where to obtain a repair scheme for a cracked lower rudder hinge fitting.
What action did the DGAC take? The DGAC classified this service bulletin as mandatory and issued French AD Number 2001-002(A), dated January 10, 2001, in order to assure the continued airworthiness of these airplanes in France.
Was this in accordance with the bilateral airworthiness agreement? These airplane models are manufactured in France and are type certificated for operation in the United States under the provisions of Sec. 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. Pursuant to this bilateral airworthiness agreement, the DGAC has kept FAA informed of the situation described above.
The FAA's Determination and an Explanation of the Provisions of the Proposed AD
What has FAA decided? The FAA has examined the findings of the DGAC; reviewed all available information, including the service information referenced above; and determined that:
--The unsafe condition referenced in this document exists or could develop on other SOCATA Models TB 9, TB 10, TB 20, TB 21, and TB 200 airplanes of the same type design;
--The actions specified in the previously-referenced service information should be accomplished on the affected airplanes; and
--AD action should be taken in order to correct this unsafe condition.
What would the proposed AD require? This proposed AD would require you to repetitively inspect the lower rudder hinge fitting for cracks and repair any crack found in accordance with a repair scheme obtained from the manufacturer through the Federal Aviation Administration (FAA).
Is there a modification I can incorporate instead of repetitively inspecting the lower rudder hinge fitting? The FAA has determined that long-term continued operational safety would be better assured by design changes that remove the source of the problem rather than by repetitive inspections or other special procedures. With this in mind, FAA will continue to work with SOCATA in collecting information and in performing fatigue analysis to determine whether a future design change may be necessary.
Cost Impact
How many airplanes would the proposed AD impact? We estimate that the proposed AD affects 239 airplanes in the U.S. registry.
What would be the cost impact of the proposed AD on owners/ operators of the affected airplanes? We estimate the following costs to accomplish the proposed inspection:
Total cost on Labor cost
Parts cost
Total cost per U.S. airplane operators
3 workhours x $60 per hour = $180........... No parts required to perform the
$180
$43,020 inspection.
[[Page 45650]]
The FAA has no method of determining the number of repetitive inspections each owner/operator would incur over the life of each of the affected airplanes so the cost impact is based on the initial inspection.
We estimate the following costs to accomplish any necessary repairs that would be required based on the results of the proposed inspections. We have no way of determining the number of repairs each owner/operator would incur over the life of each of the affected airplanes based on the results of the proposed inspections.
Total cost per Labor cost
Parts cost
Airplane
7 workhours x $60 = $420..............
$300
$720
Regulatory Impact
Would this proposed AD impact various entities? The regulations proposed herein would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this proposed rule would not have federalism implications under Executive Order 13132.
Would this proposed AD involve a significant rule or regulatory action? For the reasons discussed above, I certify that this proposed action (1) is not a ``significant regulatory action'' under Executive Order 12866; (2) is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the draft regulatory evaluation prepared for this action has been placed in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. FAA amends Sec. 39.13 by adding a new airworthiness directive (AD) to read as follows:
SOCATA--Groupe Aerospatiale: Docket No. 2001-CE-01-AD
(a) What airplanes are affected by this AD? This AD affects the following TB 9, TB 10, TB 20, TB 21, and TB 200 airplanes, all serial numbers, that are certificated in any category.
(b) Who must comply with this AD? Anyone who wishes to operate any of the above airplanes must comply with this AD.
(c) What problem does this AD address? The actions specified by this AD are intended to detect and correct fatigue cracks in the lower rudder hinge fitting. This condition could cause the lower rudder to detach from the control linkage with consequent loss of control of the airplane.
(d) What actions must I accomplish to address this problem? To address this problem, you must accomplish the following:
Actions
Compliance
Procedures
(1) Visually inspect the Upon accumulating In accordance with lower rudder hinge fitting 2,000 hours time-in- the ACCOMPLISHMENT for cracks.
service (TIS) on INSTRUCTIONS the rudder hinge section of SOCATA fitting or within Service Bulletin SB the next 100 hours 10-114 55, dated TIS after the
September 2000, and effective date of the applicable this AD, whichever aircraft occurs later, and maintenance manual. thereafter at intervals not to exceed 12 calendar months.
(2) If any crack is found Prior to further In accordance with during any inspection
flight after the the repair scheme required in paragraph
inspection required obtained from (d)(1) of this AD,
in paragraph (d)(1) SOCATA Groupe accomplish the following: of this AD.
AEROSPATIALE, (i) Obtain a repair
Customer Support, scheme from the
Aerodrome Tarbes- manufacturer through the
Ossun-Lourdes, BP FAA at the address
930--F65009 Tarbes specified in paragraph (f)
Cedex, France; of this AD; and
telephone: (33) (ii) Incorporate this
05.62.41.76.68; repair scheme
facsimile: (33) 06.07.32.62.24; or the Product Support Manager, SOCATA-- Groupe AEROSPATIALE, North Perry Airport, 7501 Pembroke Road, Pembroke Pines, Florida 33023; telephone: (954) 893-1450. Obtain this repair scheme through the FAA at the address specified in paragraph (f) of this AD.
[[Page 45651]]
(3) Report any cracks found Upon completion of Fill out the during the initial
the initial
compliance form in inspection required in
inspection required SOCATA Service paragraph (d)(1) of this AD in paragraph (d)(1) Bulletin SB 10-114 to the FAA with a copy to of this AD.
55, dated September SOCATA. Information
2000. Send it to collection requirements
the FAA at the contained in this
address specified regulation have been
in paragraph (f) of approved by the Office of
this AD. Send a Management and Budget (OMB)
copy to SOCATA at under the provisions of the
the address in Paperwork Reduction Act of
paragraph (h) of 1980 (44 U.S.C. 3501 et
this AD. seq.) and have been assigned OMB Control Number 2120-0056.
(e) Can I comply with this AD in any other way? You may use an alternative method of compliance or adjust the compliance time if:
(1) Your alternative method of compliance provides an equivalent level of safety; and
(2) The Manager, Small Airplane Directorate, approves your alternative. Submit your request through an FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Small Airplane Directorate.
Note 1: This AD applies to each airplane identified in paragraph (a) of this AD, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/ operator must request approval for an alternative method of compliance in accordance with paragraph (e) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if you have not eliminated the unsafe condition, specific actions you propose to address it.
(f) Where can I get information about any already-approved alternative methods of compliance? Contact Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; facsimile: (816) 329-4090.
(g) What if I need to fly the airplane to another location to comply with this AD? The FAA can issue a special flight permit under sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate your airplane to a location where you can accomplish the requirements of this AD.
(h) How do I get copies of the documents referenced in this AD? You may obtain copies of the documents referenced in this AD from SOCATA Groupe AEROSPATIALE, Customer Support, Aerodrome Tarbes- Ossun-Lourdes, BP 930--F65009 Tarbes Cedex, France; or the Product Support Manager, SOCATA--Groupe AEROSPATIALE, North Perry Airport, 7501 Pembroke Road, Pembroke Pines, Florida 33023. You may examine these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.
Note 2: The subject of this AD is addressed in French AD Number 2001-002(A), dated January 10, 2001.
Issued in Kansas City, Missouri, on August 22, 2001. James E. Jackson, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 01-21754Filed8-28-01; 8:45 am]
BILLING CODE 4910-13-P
