Anthropomorphic test dummies: old child dummy; design and performance specifications; response to reconsideration petitions; correction,
[Federal Register: September 19, 2002 (Volume 67, Number 182)]
[Rules and Regulations]
[Page 59020-59024]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr19se02-16]
DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
[Docket No. NHTSA-02-12541]
RIN 2127-AI00
Anthropomorphic Test Devices; Six-Year-Old Crash Test Dummy
AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of Transportation.
ACTION: Final rule; correcting amendment.
SUMMARY: This document makes technical corrections to the final rule published in response to petitions for reconsideration on July 18, 2002. That rule amended an earlier rule, published on January 13, 2000, that had adopted a new, more advanced 6-year-old child dummy (HIII-6C). The changes made in today's notice consist of corrections of typographical errors in the table in the preamble, the addition of a revised Figure N5, and minor revisions in the weight and length specifications of the head skin and upper arm molded assembly, respectively.
DATES: Effective Date: The amendments made in this rule are effective August 19, 2002.
Petitions: Petitions for reconsideration must be received by November 4, 2002.
ADDRESSES: Petitions for reconsideration should refer to the docket and notice number of this document and be submitted to: Administrator, National Highway Traffic Safety Administration, 400 Seventh Street, SW., Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: For non-legal issues, you may call Stan Backaitis, Office of Crashworthiness Standards, at 202-366-4912.
For legal issues, you may call Rebecca MacPherson, Office of the Chief Counsel, at 202-366-2992.
You may send mail to both of these officials at National Highway Traffic Safety Administration, 400 Seventh St., SW., Washington, DC 20590.
SUPPLEMENTARY INFORMATION: NHTSA published a final rule on July 18, 2002 (67 FR 47321, Docket No. NHTSA-02-12541) that responded to various petitions for reconsideration of its
[[Page 59021]]
previous rule incorporating a new, Hybrid III 6-year-old child anthropomorphic test dummy (HIII-6C) into 49 CFR part 572. That final rule was published January 13, 2000 (65 FR 2059, Docket No. NHTSA-99- 6714). The petitions were granted in part and denied in part.
Most of the issues raised in the petitions were minor and involved technical changes to either the dummy specifications or to the drawing package. In some cases, the petitioners had requested the specifications be tightened to ensure more accurate measurements in the tests in which the dummy is used to measure injury criteria. More significant issues were raised regarding the thoracic peak force criteria, the need for a specified mass moment of inertia (MMI) and resonant frequency of the impactors, and the need for a post-test calibration. Our review of the petitions also uncovered several minor errors in the drawings package that were resolved. All these issues were addressed in the July 18, 2002 final rule.
We are issuing a correcting amendment because that document contained a few technical errors. Namely, we inadvertently failed to submit the amended Figure N5 when the final rule was forwarded to the Federal Register for publication, and Table 1 of the preamble contained two typographical errors and two omissions. While Table 1 is not part of the regulatory text, and the changes to that table in this notice will have no effect on what is ultimately published in the Code of Federal Regulations, we have decided to amend the table since it provides a quick reference of those changes to the drawing package incorporated by reference into 49 CFR part 572, subpart N.
Changes in ``N'' Figures
As noted in the preamble to the July 2002 final rule, the following changes were made to the figures included as part of 49 CFR 572, subpart N to correct inaccuracies or ambiguities in those figures.
[sbull] Figure N2: (1) Relocate the 26.1 mm reference to the centerline of the posterior attachment bolt to reflect dimensional proportionality; (2) change reference from ``Neck Flexion Pendulum 46 CFRSec. 572.33 FIG 22'' to ``Neck Flexion Pendulum 49 CFR 572.33 FIG 22''; and (3) add part number for bolt ``9001265 Screw, SHCS 10-24 x 7/16''.
[sbull] Figure N3: (1) Relocate the 26.1 mm reference to the centerline of the posterior attachment bolt to reflect dimensional proportionality; and (2) add part number for bolt ``9001265 Screw, SHCS 10-24 x 7/16''.
[sbull] Figure N5: Change bracket dimensions from ``89.9 mm (3.54 in) x 161.3 mm (6.35 in) x 31.8 mm (1.251 in)'' to ``90.4 mm (3.56 in) x 175.5 mm (6.91 in) x 31.8 mm (1.25 in)''.
[sbull] Figure N6: (1) Remove note SA572-S4; and (2) change the weight tolerance on the knee probe from ``0.82 +/- 0.01 kg (1.80 +/- .02lb)'' to ``0.82 +/- 0.02kg (1.80 +/- .05 lb)''.
No changes were made to Figure N1. Figure N1, rather than Figure N5 was inadvertently sent to the Federal Register as part of the final rule. Accordingly, the changes that were made to figure N5 do not appear in the revised regulatory text. Today's amendment corrects that error.
Errors and Corrections in Drawings
In responding to the petitions for reconsideration, several minor inconsistencies and call-out errors were noted either by petitioners or by agency staff in the review process. Accordingly, the changes that were made to the drawing package were noted in Table 1 of the final rule. That table contained two typographical errors, one under item 127-8210 and the other under item SA 572-S50, which are corrected here. Additionally, just before publication of the final rule, we discovered two errors in the drawings package that were not identified in Table 1: to wit, the head skin weight specification in drawing 127-1008 was changed from 1.78 +/- .05 lbs to 1.55 +/- .05 lbs, and the molded length specification for the upper arm molded assembly in drawing 127- 5001 was revised from 5.24 in to 4.6 in. While these errors were not discussed in the final rule, they were corrected prior to publication of the final rule. Accordingly, both the drawings package sent to Reprographic Technologies and the one placed on public display at NHTSA technical reference library were correct. There is no need for purchasers of the drawing package to repurchase the package. Table 1 is recreated in whole so that readers may refer to a single, correct table.
Table 1
Drawing/part No.
Description Revision description
127-SBL...................... 6 year H3
Deleted drawing. standard build level. SA572-127DRL-1............... Drawing
New drawing. revision list. 127-0000..................... Hybrid III 6 Corrected location of year old
``I'' dimension (on complete
sheet 5 of 6), all assembly.
sheets revised to change letter''K''. 127-1008..................... 6 year H3 head Changed weight skin.
specification of head skin from 1.78 +/- .05 lbs to 1.55 +/- .05 lbs. 127-1009..................... Skin cap, skull Added ``reference'' to item 1, corrected title. 127-2011..................... Sternum pad.... Corrected angle dimensions. 127-2550..................... Chest-
Corrected accelerometer accelerometer mount drawing number assembly
from 127-2110 to 127- (SA572-S4). 2150. 127-4002..................... Upper leg flesh Defined angular orientation of 0.5 dia. ``Posts''; Assigned missing hole diameters for load cell installation. 127-5001..................... 6 year H3 upper Changed upper arm molded arm molded length specification assembly.
from 5.24 in. to 4.6 in. 127-8210..................... 6 yr old
Changed dimension from abdominal
1.90 to 1.40 (notch insert.
depth), changed dimension 4.30 to 3.81 (overall height). SA572-S4..................... Uniaxial
Changed single decimal piezorestive place tolerance from +/- accelerometer. 0.1/2.54 to +/- 0.1/ 2.5, corrected metric equivalents, and added dimensions. SA572-S10.................... Femur load cell Revised tolerance format, changed single decimal place tolerance from +/- 0.1/2.54 to +/- 0.1/2.5, changed reference note from ``Subpart E'' to ``Subpart N'', added material note, changed output at capacity from 1 mV/V min. to 0.75 mV/ V min., added ``weight includes * * *'' note, and removed ``+'' from the Fz axis. SA572-S11.................... Upper neck load Revised tolerance cell.
format, changed single decimal place tolerance from +/- 0.1/2.54 to +/- 0.1/2.5, added material note, changed output at capacity from 1 mV/V min. to 0.75 mV/ V min.
[[Page 59022]]
SA572-S12.................... Lumbar load Changed hole dimension cell.
from 0.75/.1905 x .37/ .89 to 0.63/16.0 x .35/ 8.9, changed weight from 1.3 lb/0.59 kg max to 1.35 lb/0.61 kg max, revised tolerance format, changed single decimal place tolerance from +/- 0.1/2.54 to +/- 0.1/2.5, changed reference note from ``Subpart E'' to ``Subpart N'', added material note, changed output at capacity from 1 mV/V min. to 0.75 mV/ V min., added ``weight includes . . . '' note, and revised hole dimensions. SA572-S13-L&R................ Anterior-
Changed output at superior iliac capacity from 1 mV/V spine load min. to 0.75 mV/V min., cell.
revised tolerance format, changed reference note from ``Subpart E'' to ``Subpart N'', added material note, changed single decimal place tolerance from +/- 0.1/ 2.54 to +/- 0.1/2.5, and added ``weight includes . . .'' note. SA572-S26.................... Lower neck load Revised tolerance cell.
format, changed single decimal place tolerance from +/- 0.1/2.54 to +/- 0.1/2.5, added material note, changed output at capacity from 1 mV/V min. to 0.75 mV/ V min., added ``(does not include cables)'' to the weight note, added hole dimensions, and changed reference note from subpart E to subpart N. SA572-S50.................... Chest
Changed single decimal potentiometer. tolerance from +/- 0.1/ 2.54 to +/- 0.1/2.5, added/corrected metric equivalents, added ``Dia. Of hard shell housing'' and ``in rotary rigid shaft'' to notes, added ``signal connector pins'' note, and added ``locating'' and ``Dia.'' to pin note. SA572-S80.................... S4 triaxial Changed single decimal accelerometer place tolerance from +/- mounting block. 0.1/2.54 to +/- 0.1/ 2.5, corrected metric equivalents, revised hole note, and relocated holes. TE-2208-001.................. Neck adapter Added part 9001265 and note year old.
3, changed single decimal place tolerance from +/- 0.1/ 2.54 to +/- 0.1/2.5. 9001373...................... Bushing,
New drawing. shoulder. 9000000 & 6000000............ Hardware used Added part 9001265, removed part 5th female. 9001373.
Regulatory Analyses and Notices
Executive Order 12866 and DOT Regulatory Policies and Procedures
Executive Order 12866, ``Regulatory Planning and Review'' (58 FR 51735, October 4, 1993), provides for making determinations whether a regulatory action is ``significant'' and therefore subject to Office of Management and Budget (OMB) review and to the requirements of the Executive Order. The Order defines a ``significant regulatory action'' as one that is likely to result in a rule that may:
(1) Have an annual effect on the economy of $100 million or more or adversely affect in a material way the economy, a sector of the economy, productivity, competition, jobs, the environment, public health or safety, or State, local, or Tribal governments or communities;
(2) Create a serious inconsistency or otherwise interfere with an action taken or planned by another agency;
(3) Materially alter the budgetary impact of entitlements, grants, user fees, or loan programs or the rights and obligations of recipients thereof; or
(4) Raise novel legal or policy issues arising out of legal mandates, the President's priorities, or the principles set forth in the Executive Order.
We considered the impact of the July 18, 2002 rulemaking action under Executive Order 12866 and the Department of Transportation's regulatory policies and procedures. This rule is not considered a significant regulatory action under section 3(f) of the Executive Order 12866. Consequently, it was not reviewed by the Office of Management and Budget under E.O. 12866, ``Regulatory Planning and Review.'' The rulemaking action is also not considered to be significant under the Department's Regulatory Policies and Procedures (44 FR 11034, February 26, 1979). Today's notice does not impose any new requirements on manufacturers. It simply corrects typographical errors and adds information to a table that is not part of the regulatory text and adds the correct amended figure to the regulatory text.
Executive Order 13132
Executive Order 13132 requires NHTSA to develop an accountable process to ensure ``meaningful and timely input by State and local officials in the development of regulatory policies that have federalism implications.'' ``Policies that have federalism implications'' is defined in the Executive Order to include regulations that have ``substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.'' Under Executive Order 13132, the agency may not issue a regulation with Federalism implications, that imposes substantial direct compliance costs, and that is not required by statute, unless the Federal government provides the funds necessary to pay the direct compliance costs incurred by State and local governments, the agency consults with State and local governments, or the agency consults with State and local officials early in the process of developing the proposed regulation. NHTSA also may not issue a regulation with Federalism implications and that preempts State law unless the agency consults with State and local officials early in the process of developing the proposed regulation. As explained above, today's notice will not have any additional economic impact on any entities.
Executive Order 13045
Executive Order 13045 (62 FR 19885, April 23, 1997) applies to any rule that: (1) is determined to be ``economically significant'' as defined under E.O. 12866, and (2) concerns an environmental, health or safety risk that NHTSA has reason to believe may have a disproportionate effect on children. If the regulatory action meets both criteria, we must evaluate the environmental health or safety effects of the planned rule on children, and explain why the planned regulation is preferable to other potentially effective and reasonably feasible alternatives considered by us.
This rule is not subject to the Executive Order because it is not economically significant as defined in E.O. 12866. It does indirectly involve decisions based on health risks that disproportionately affect children, namely, the risk of deploying air bags to children. However, this rulemaking
[[Page 59023]]
serves to help vehicle and air bag manufacturers to take steps to reduce that risk.
Executive Order 12778
Pursuant to Executive Order 12778, ``Civil Justice Reform,'' we have considered whether this rule will have any retroactive effect. This rule does not have any retroactive effect. A petition for reconsideration or other administrative proceeding will not be a prerequisite to an action seeking judicial review of this rule. This rule does not preempt the states from adopting laws or regulations on the same subject, except that it does preempt a state regulation that is in actual conflict with the federal regulation or makes compliance with the Federal regulation impossible or interferes with the implementation of the federal statute.
Regulatory Flexibility Act
Pursuant to the Regulatory Flexibility Act (5 U.S.C. 601 et seq., as amended by the Small Business Regulatory Enforcement Fairness Act (SBREFA) of 1996) whenever an agency is required to publish a notice of rulemaking for any proposed or final rule, it must prepare and make available for public comment a regulatory flexibility analysis that describes the effect of the rule on small entities (i.e., small businesses, small organizations, and small governmental jurisdictions). However, no regulatory flexibility analysis is required if the head of an agency certifies the rule will not have a significant economic impact on a substantial number of small entities. SBREFA amended the Regulatory Flexibility Act to require Federal agencies to provide a statement of the factual basis for certifying that a rule will not have a significant economic impact on a substantial number of small entities.
I have considered the effects of this rulemaking action under the Regulatory Flexibility Act (5 U.S.C. 601 et seq.) and certify that this proposal will not have a significant economic impact on a substantial number of small entities. The amendments made in this document will not affect the cost of the dummy. The rule does not impose or rescind any requirements for anyone. The Regulatory Flexibility Act does not, therefore, require a regulatory flexibility analysis.
National Environmental Policy Act
We have analyzed this amendment for the purposes of the National Environmental Policy Act and determined that it will not have any significant impact on the quality of the human environment.
Paperwork Reduction Act
Under the Paperwork Reduction Act of 1995, a person is not required to respond to a collection of information by a Federal agency unless the collection displays a valid OMB control number. This rule does not propose any new information collection requirements.
National Technology Transfer and Advancement Act
Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (NTTAA), Public Law 104-113, section 12(d) (15 U.S.C. 272) directs us to use voluntary consensus standards in its regulatory activities unless doing so would be inconsistent with applicable law or otherwise impractical. Voluntary consensus standards are technical standards (e.g., materials specifications, test methods, sampling procedures, and business practices) that are developed or adopted by voluntary consensus standards bodies, such as the Society of Automotive Engineers (SAE). The NTTAA directs us to provide Congress, through OMB, explanations when we decide not to use available and applicable voluntary consensus standards.
The H-III6C dummy that is the subject of this document was developed under the auspices of the SAE. All relevant SAE standards were reviewed as part of the development process. The following voluntary consensus standards have been used in developing the dummy:
[sbull] SAE Recommended Practice J211-1995, ``Instrumentation for Impact Tests--Parts 1 and 2'', dated March, 1995; and
[sbull] SAE J1733 Information Report, titled ``Sign Convention for Vehicle Crash Testing'', dated December 1994.
Unfunded Mandates Reform Act
Section 202 of the Unfunded Mandates Reform Act of 1995 (UMRA) requires Federal agencies to prepare a written assessment of the costs, benefits and other effects of proposed or final rules that include a Federal mandate likely to result in the expenditure by State, local or tribal governments, in the aggregate, or by the private sector, of more than $100 million in any one year (adjusted for inflation with base year of 1995). Before promulgating a NHTSA rule for which a written statement is needed, section 205 of the UMRA generally requires us to identify and consider a reasonable number of regulatory alternatives and adopt the least costly, most cost-effective or least burdensome alternative that achieves the objectives of the rule. The provisions of section 205 do not apply when they are inconsistent with applicable law. Moreover, section 205 allows us to adopt an alternative other than the least costly, most cost-effective or least burdensome alternative if we publish with the final rule an explanation why that alternative was not adopted.
This rule does not impose any unfunded mandates under the Unfunded Mandates Reform Act of 1995. This rule does not meet the definition of a Federal mandate because it does not impose requirements on anyone. Further, it will not result in costs of $100 million or more to either State, local, or tribal governments, in the aggregate, or to the private sector. The amendments made in this document will not affect the cost of the dummy. Thus, this rule is not subject to the requirements of sections 202 and 205 of the UMRA.
Regulation Identifier Number (RIN)
The Department of Transportation assigns a regulation identifier number (RIN) to each regulatory action listed in the Unified Agenda of Federal Regulations. The Regulatory Information Service Center publishes the Unified Agenda in April and October of each year. You may use the RIN contained in the heading at the beginning of this document to find this action in the Unified Agenda.
List of Subjects in 49 CFR Part 572
Incorporation by reference, Motor vehicle safety.
In consideration of the foregoing, NHTSA amends 49 CFR Part 572 as follows:
PART 572--ANTHROPOMORPHIC TEST DUMMIES
-
The authority citation for Part 572 continues to read as follows:
Authority: 49 U.S.C. 322, 30111, 30115, 30117 and 30166; delegation of authority at 49 CFR 1.50.
-
By revising Figure N5 to Subpart N to read as follows:
Figures to Subpart N
* * * * *
[[Page 59024]]
[GRAPHIC] [TIFF OMITTED] TR19SE02.000
Issued: September 11, 2002. Stephen R. Kratzke, Associate Administrator for Rulemaking.
[FR Doc. 02-23512Filed9-18-02; 8:45 am]
BILLING CODE 4910-59-C
