Airworthiness directives: Australia Pty Ltd.; AeroSpace Technologies,
[Federal Register: October 24, 2003 (Volume 68, Number 206)]
[Proposed Rules]
[Page 60887-60891]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr24oc03-23]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
[Docket No. 2003-CE-37-AD]
RIN 2120-AA64
Airworthiness Directives; AeroSpace Technologies of Australia Pty Ltd. Models N22B, N22S, and N24A Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for all AeroSpace Technologies of Australia Pty Ltd. (ASTA) Models N22B, N22S, and N24A airplanes. This proposed AD would require you to repetitively inspect wing fittings for fatigue defects, replace or correct defective wing fittings, and replace the stub wing front spar assembly and wing fitting when fatigue life limits are reached. This proposed AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Australia. We are issuing this proposed AD to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.
DATES: We must receive any comments on this proposed AD by December 4, 2003.
ADDRESSES: Use one of the following to submit comments on this proposed AD:
[sbull] By mail: FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-37-AD, 901 Locust, Room 506, Kansas City, Missouri 64106.
[sbull] By fax: (816) 329-3771. [sbull] By e-mail: 9-ACE-7-Docket@faa.gov. Comments sent electronically must contain ``Docket No. 2003-CE-37-AD'' in the subject line. If you send comments electronically as attached electronic files, the files must be formatted in Microsoft Word 97 for Windows or ASCII.
You may get the service information identified in this proposed AD from Nomad Operations, Aerospace Support Division, Boeing Australia, PO Box 767, Brisbane, QLD 4000 Australia; telephone 61 7 3306 3366; facsimile 61 7 3306 3111.
You may view the AD docket at FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2003-CE-37-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. Office hours are 8 a.m. to 4 p.m., Monday through Friday, except Federal holidays.
FOR FURTHER INFORMATION CONTACT: Ron Atmur, Aerospace Engineer, FAA, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California 90712; telephone (562) 627-5224; facsimile (562) 627-5210.
SUPPLEMENTARY INFORMATION:
[[Page 60888]]
Comments Invited
How do I comment on this proposed AD? We invite you to submit any written relevant data, views, or arguments regarding this proposal. Send your comments to an address listed under ADDRESSES. Include ``AD Docket No. 2003-CE-37-AD'' in the subject line of your comments. If you want us to acknowledge receipt of your mailed comments, send us a self- addressed, stamped postcard with the docket number written on it. We will date-stamp your postcard and mail it back to you.
Are there any specific portions of this proposed AD I should pay attention to? We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. If you contact us through a nonwritten communication and that contact relates to a substantive part of this proposed AD, we will summarize the contact and place the summary in the docket. We will consider all comments received by the closing date and may amend this proposed AD in light of those comments and contacts.
Discussion
What events have caused this proposed AD? The Civil Aviation Safety Authority (CASA), which is the airworthiness authority for Australia, recently notified FAA that an unsafe condition may exist on all ASTA Models N22B, N22S, and N24A airplanes. The CASA reports that fatigue tests on the wing strut upper end fitting have shown premature failures and rapid crack growth. Also, fatigue tests on the wing strut lower end fittings, stub wing strut pick up fitting, and stub wing front spar assembly have identified appropriate fatigue lives for the respective parts.
What are the consequences if the condition is not corrected? Fatigue loading could result in failure of the wing strut upper end fitting, wing strut lower end fittings, stub wing strut pick up fitting, or stub wing front spar assembly. Such failure could lead to reduced structural capability or reduced controllability of the airplane.
Is there service information that applies to this subject? Boeing Australia (formerly ASTA) Aerospace Technologies of Australia has issued:
--Nomad Alert Service Bulletin No. ANMD-57-12, Revision 2, dated May 25, 1999; --Nomad Service Bulletin No. NMD-53-18, dated February 8, 1996; and --Nomad Service Bulletin No. NMD-53-18, Revision 1, dated September 3, 2002.
What are the provisions of this service information? The service bulletins include procedures for:
--Performing a fatigue inspection of the stub wing strut pick-up fittings for cracks; --Replacing the stub wing strut pick-up fittings; --Inspecting (visually) the strut to upper strut fittings bolt holes for scoring, ovality, fretting, corrosion, and dimensions; --Inspecting (eddy current method) the strut to upper strut fittings bolt holes for cracks; --Modifying (line ream) the strut to upper strut fitting bolt holes; --Replacing bolts for the strut upper end fittings; and --Replacing the strut upper end fittings.
What action did the CASA take? The CASA classified these service bulletins as mandatory and issued these Australian ADs in order to ensure the continued airworthiness of these airplanes in Australia:
--AD Number AD/GAF-N22/2, Amendment 3, dated January 28, 2003; and --AD Number AD/GAF-N22/70, Amendment 2, dated January 28, 2003.
FAA's Determination and Requirements of This Proposed AD
What has FAA decided? We have examined the CASA's findings, reviewed all available information, and determined that AD action is necessary for products of this type design that are certificated for operation in the United States.
Since the unsafe condition described previously is likely to exist or develop on other ASTA Models N22B, N22S, and N24A airplanes of the same type design that are registered in the United States, we are proposing AD action to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.
What would this proposed AD require? This proposed AD would require you to incorporate the actions in the previously-referenced service bulletin.
How does the revision to 14 CFR part 39 affect this proposed AD? On July 10, 2002, we published a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs FAA's AD system. This regulation now includes material that relates to altered products, special flight permits, and alternative methods of compliance. This material previously was included in each individual AD. Since this material is included in 14 CFR part 39, we will not include it in future AD actions.
Costs of Compliance
How many airplanes would this proposed AD impact? We estimate that this proposed AD affects 15 airplanes in the U.S. registry.
What would be the cost impact of this proposed AD on owners/ operators of the affected airplanes? We estimate the following costs to accomplish the proposed inspection of the wing strut upper end fitting bolt holes:
Total cost per Labor cost
Parts cost
airplane Total cost on U.S. operators
12 workhours x $65 per hour = $780.... Not applicable..........
$780
15 x $780 = $11,700
We estimate the following costs to accomplish the proposed inspection of the stub wing strut pick up fittings:
Total cost per Labor cost
Parts cost
airplane Total cost on U.S. operators
16 workhours x $65 per hour = $1,040.. Not applicable..........
$1,040
15 x $1,040 = $15,600
[[Page 60889]]
We estimate the following costs to accomplish any necessary replacements of the wing strut upper end fittings that would be required based on the results of the proposed inspection or on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:
Labor cost
Parts cost Total cost per airplane
10 workhours x $65 per hour = $650..............................
$679
$650 + $679 = $1,329
We estimate the following costs to accomplish any necessary replacements of the wing strut lower end fittings that would be required based on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:
Labor cost
Parts cost
Total cost per airplane
12 workhours x $65 per hour = $780..............................
$193
$780 + $193 = $973
We estimate the following costs to accomplish any necessary replacements of the stub wing strut pick up fittings that would be required based on the results of the proposed inspection or on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:
Labor cost
Parts cost
Total cost per airplane
80 workhours x $65 per hour = $5,200............................
$985
$5,200 + $985 = $6,185
We estimate the following costs to accomplish any necessary replacements of the stub wing front spar assembly that would be required based on reaching the fatigue life limit. We have no way of determining the number of airplanes that may need such replacement:
Labor cost
Parts cost
Total cost per airplane
370 workhours x $65 per hour = $24,050..........................
$4,820 $24,050 + $4,820 = $28,870
Regulatory Findings
Would this proposed AD impact various entities? We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
Would this proposed AD involve a significant rule or regulatory action? For the reasons discussed above, I certify that this proposed AD:
-
Is not a ``significant regulatory action'' under Executive Order 12866;
-
Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
-
Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a summary of the costs to comply with this proposed AD and placed it in the AD Docket. You may get a copy of this summary by sending a request to us at the address listed under ADDRESSES. Include ``AD Docket No. 2003-CE-37-AD'' in your request.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
-
The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
-
The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):
AeroSpace Technologies of Australia Pty Ltd.: Docket No. 2003-CE-37- AD
When Is the Last Date I Can Submit Comments on This Proposed AD Action?
(a) We must receive comments on this proposed airworthiness directive (AD) action by December 4, 2003.
Are Any Other ADs Affected by This Action?
(b) None.
What Airplanes Are Affected by This AD?
(c) This AD affects Models N22B, N22S, and N24A airplanes, all serial numbers, that are certificated in any category.
What Is the Unsafe Condition Presented in This AD?
(d) This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Australia. The actions specified in this AD are intended to detect and correct defects in the wing strut upper end fittings, wing strut lower end fittings, stub wing strut pick up fittings, and the stub wing front spar assembly. These defects could result in failure of the fittings or spar assembly and lead to reduced structural capability or reduced controllability of the airplane.
What Must I Do To Address This Problem?
(e) To address this problem, you must accomplish the following:
[[Page 60890]]
Actions
Compliance
Procedures
(1) Inspect the wing strut For Models N22S and Follow the upper end fitting bolt
N24A: Initially Accomplishment holes:
inspect before
Instructions in (i) Visually inspect for 3,600 hours time-in- Boeing Australia scoring, ovality, fretting, service (TIS) on Aerospace corrosion, and dimensions; the wing strut
Technologies of and
upper end fitting Australia Nomad (ii) Inspect, using eddy or within the next Alert Service current inspection, for 100 hours TIS after Bulletin No. ANMD- cracks.
the effective date 57-12, Revision 2, of this AD,
dated May 25, 1999. whichever occurs later. Repetitively inspect thereafter at every 900 hours TIS until 14,400 hours TIS are accumulated on the wing strut upper end fitting. For Model N22B: Initially inspect before 5,400 hours TIS on the wing strut upper end fitting or within the next 100 hours TIS after the effective date of this AD, whichever occurs later. Repetitively inspect thereafter at every 1,200 hours TIS until 14,400 hours TIS are accumulated on the wing strut upper end fitting. (2) Complete corrective Before further
Follow the actions for defects of the flight after the Accomplishment wing strut upper end
inspection required Instructions in fittings:
in paragraph (e)(1) Boeing Australia (i) If a crack is found or of this AD, unless Aerospace the hole in the strut upper already
Technologies of end fitting is damaged and accomplished.
Australia Nomad will not clean up, replace
Alert Service the wing strut upper end
Bulletin No. ANMD- fittings.
57-12, Revision 2, (ii) If the hole in the
dated May 25, 1999; strut is oval or damaged,
and any repair and the oversize line
scheme obtained reamer will not repair it:.
from Nomad (A) Get a repair scheme from
Operations, the manufacturer; and.
Aerospace Support (B) Follow this repair
Division, Boeing scheme..
Australia, PO Box (iii) If scoring, fretting,
767, Brisbane, QLD or corrosion is found, or
4000 Australia; all dimensions are within
telephone 61 7 3306 limits, line ream the hole
3366; facsimile 61 and replace the bolt.
7 3306 3111. Obtain approval of this repair scheme through the FAA at the address specified in paragraph (f) of this AD. (3) Replace the wing strut Before further
Follow the upper end fittings.
flight when cracks Accomplishment are found by the Instructions in inspection required Boeing Australia in paragraph
Aerospace (e)(1); and upon Technologies of the accumulation of Australia Nomad 14,400 hours TIS on Alert Service the fitting or
Bulletin No. ANMD- within the next 100 57-12, Revision 2, hours TIS after the dated May 25, 1999. effective date of this AD, whichever occurs later. For Models N22S and N24A: start repetitive inspections of paragraph (e)(1) of this AD when 7,200 hours TIS are accumulated on the wing strut upper end fitting. For Models N22B: start repetitive inspections of paragraph (e)(1) of this AD when 10,800 hours TIS are accumulated on the wing strut upper end fitting. (4) Replace the wing strut Upon the
Follow a repair lower end fittings:
accumulation of scheme from Nomad (i) Get a repair scheme from 14,000 hours TIS on Operations, the manufacturer; and.
the fitting or
Aerospace Support (ii) Follow this repair
within the next 100 Division, Boeing scheme..
hours TIS after the Australia, PO Box effective date of 767, Brisbane, QLD this AD, whichever 4000 Australia; occurs later.
telephone 61 7 3306 3366; facsimile 61 7 3306 3111. Get approval of this repair scheme through the FAA at the address specified in paragraph (f) of this AD. (5) Inspect the stub wing Initially inspect Follow the strut pick up fittings for upon the
Accomplishment cracks.
accumulation of Instructions in 5,400 hours TIS on Aerospace the fitting or
Technologies of within the next 300 Australia Nomad hours TIS on the Service Bulletin fitting after the No. NMD-53-18, effective date of dated February 8, this AD, whichever 1996; or Boeing occurs later.
Australia Aerospace Repetitively
Technologies of inspect thereafter Australia Nomad at every 1,800
Service Bulletin hours TIS until No. NMD-53-18, 18,800 hours TIS Revision 1, dated are accumulated on September 3, 2002; the stub wing strut and the applicable pick up fitting. airplane maintenance manual. (6) Replace the stub wing Before further
Follow the strut pick up fittings. flight when cracks Accomplishment are found after the Instructions in inspection required Aerospace in paragraph (e)(5) Technologies of of this AD, unless Australia Nomad already
Service Bulletin accomplished; and No. NMD-53-18, upon the
dated February 8, accumulation of 1996; or Boeing 18,800 hours TIS or Australia Aerospace 300 hours TIS after Technologies of the effective date Australia Nomad of this AD,
Service Bulletin whichever occurs No. NMD-53-18, later.
Revision 1, dated September 3, 2002; and the applicable airplane maintenance manual.
[[Page 60891]]
(7) Replace the stub wing Upon the
Follow a repair front spar assembly:
accumulation of scheme from Nomad (i) Get a repair scheme from 25,000 hours TIS on Operations, the manufacturer; and.
the fitting or
Aerospace Support (ii) Follow this repair
within the next 100 Division, Boeing scheme..
hours TIS after the Australia, PO Box effective date of 767, Brisbane, QLD this AD, whichever 4000 Australia; occurs later.
telephone 61 7 3306 3366; facsimile 61 7 3306 3111. Get approval of this repair scheme through the FAA at the address specified in paragraph (f) of this AD.
What About Alternative Methods of Compliance?
(f) You may request a different method of compliance or a different compliance time for this AD by following the procedures in 14 CFR 39.13. Send your request to the Manager, Los Angeles Aircraft Certification Office, FAA. For information on any already approved alternative methods of compliance, contact Ron Atmur, Aerospace Engineer, FAA, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California 90712; telephone (562) 627-5224; facsimile (562) 627-5210.
How Do I Get Copies of the Documents Referenced in This AD?
(g) You may get copies of the documents referenced in this AD from Nomad Operations, Aerospace Support Division, Boeing Australia, PO Box 767, Brisbane, QLD 4000 Australia; telephone 61 7 3306 3366; facsimile 61 7 3306 3111. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.
Is There Other Information That Relates to This Subject?
(h) These Australian ADs also address the subject of this AD: AD Number AD/GAF-N22/2, Amendment 3, dated January 28, 2003, and AD Number AD/GAF-N22/70, Amendment 2, dated January 28, 2003.
Issued in Kansas City, Missouri, on October 20, 2003. Michael Gallagher, Manager, Small Airplane Directorate, Aircraft Certification Service.
[FR Doc. 03-26899 Filed 10-23-03; 8:45 am]
BILLING CODE 4910-13-P
