Airworthiness Directives: Bombardier Model CL 600 2C10 (Regional Jet Series 700, 701, & 702) Airplanes, Model CL 600 2D15, etc.

Federal Register: May 8, 2008 (Volume 73, Number 90)

Proposed Rules

Page 26045-26047

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

DOCID:fr08my08-26

Page 26045

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration 14 CFR Part 39

Docket No. FAA-2008-0522; Directorate Identifier 2008-NM-041-AD

RIN 2120-AA64

Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional

Jet Series 700, 701, & 702) Airplanes, Model CL-600-2D15 (Regional Jet

Series 705) Airplanes, and Model CL-600-2D24 (Regional Jet Series 900)

Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

Following in-flight test deployments on CL-600-2B19 aircraft, several Air-Driven generators (ADGs) failed to come on-line.

Investigation revealed that, as a result of a wiring anomaly that had not been detected during ADG manufacture, a short circuit was possible between certain internal wires and their metallic over- braided shields, which could result in the ADG not providing power when deployed. * * *

The unsafe condition is that failure of the ADG could lead to loss of several functions essential for safe flight. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by June 9, 2008.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue, SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New

Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Examining the AD Docket

You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer,

Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft

Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New

York 11590; telephone (516) 228-7303; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2008-0522;

Directorate Identifier 2008-NM-041-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We will post all comments we receive, without change, to http:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF- 2008-10, dated February 5, 2008 (referred to after this as ``the

MCAI''), to correct an unsafe condition for the specified products. The

MCAI states:

Following in-flight test deployments on CL-600-2B19 aircraft, several Air-Driven generators (ADGs) failed to come on-line.

Investigation revealed that, as a result of a wiring anomaly that had not been detected during ADG manufacture, a short circuit was possible between certain internal wires and their metallic over- braided shields, which could result in the ADG not providing power when deployed. This directive mandates checking of the ADG and modification of the ADG internal wiring, if required. It also prohibits future installation of unmodified ADGs.

The unsafe condition is that failure of the ADG could lead to loss of several functions essential for safe flight. You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Bombardier has issued Service Bulletin 670BA-24-015, Revision A, dated December 18, 2006. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 304 products of U.S. registry. We also estimate that it would take about 5 work hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work hour. Required parts would cost about $0 per product. Where the service information lists required parts costs that are covered under warranty, we have assumed that there will be no charge for these costs.

As we do not control warranty coverage for affected parties, some parties may

Page 26046

incur costs higher than estimated here. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $121,600, or $400 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation

Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in

``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation: 1. Is not a ``significant regulatory action'' under Executive Order 12866; 2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the

Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended] 2. The FAA amends Sec. 39.13 by adding the following new AD:

Bombardier, Inc. (Formerly Canadair): Docket No. FAA-2008-0522;

Directorate Identifier 2008-NM-041-AD.

Comments Due Date

(a) We must receive comments by June 9, 2008.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Bombardier Model CL-600-2C10 (Regional

Jet Series 700, 701, & 702) airplanes, having serial numbers (SNs) 10004 and subsequent; and Model CL-600-2D15 (Regional Jet Series 705) airplanes and Model CL-600-2D24 (Regional Jet Series 900) airplanes, having SN 15002 and subsequent; certificated in any category.

Subject

(d) Air Transport Association (ATA) of America Code 24:

Electrical Power.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

Following in-flight test deployments on CL-600-2B19 aircraft, several Air-Driven generators (ADGs) failed to come on-line.

Investigation revealed that, as a result of a wiring anomaly that had not been detected during ADG manufacture, a short circuit was possible between certain internal wires and their metallic over- braided shields, which could result in the ADG not providing power when deployed. This directive mandates checking of the ADG and modification of the ADG internal wiring, if required. It also prohibits future installation of unmodified ADGs.

The unsafe condition is that failure of the ADG could lead to loss of several functions essential for safe flight.

Actions and Compliance

(f) Unless already done, do the following actions.

(1) For airplanes identified in Table 1 of this AD: Within 12 months after the effective date of this AD, inspect the serial number of the installed ADG. A review of airplane maintenance records is acceptable in lieu of this inspection if the serial number of the ADG can be conclusively determined from that review.

Table 1.--Bombardier Airplane Identification

Model

Serial No.

CL-600-2C10 airplanes.......... 10004 through 10265.

CL-600-2D15 and CL-600-2D24

15002 through 15162. airplanes.

(i) If the serial number is not listed in paragraph 1.A of

Bombardier Service Bulletin 670BA-24-015, Revision A, dated December 18, 2006, no further action is required by this AD.

(ii) If the serial number is listed in paragraph 1.A of

Bombardier Service Bulletin 670BA-24-015, Revision A, dated December 18, 2006, before further flight, inspect the ADG identification plate and, as applicable, do the actions of paragraph (f)(1)(ii)(A) or (f)(1)(ii)(B) of this AD.

(A) If the identification plate is marked with the symbol ``24- 2'', no further action is required by this AD.

(B) If the identification plate is not marked with the symbol

``24-2'', modify the ADG wiring in accordance with the

Accomplishment Instructions of the service bulletin.

(2) For all Model CL-600-2C10 airplanes having SN 10004 and subsequent, and Model CL-600-2D15 and CL-600-2D24 airplanes having

SN 15002 and subsequent: As of the effective date of this AD, no ADG part number 604-90800-19 (761339E), having SN 0101 through 0132, 0134 through 0167, 0169 through 0358, 0360 through 0438, 0440 through 0456, 0458 through 0467, 0469, 0471 through 0590, 0592 through 0597, 0599 through 0745, 0747 through 1005, or 1400 through 1439, may be installed on any airplane, unless the identification plate of the ADG is identified with the symbol ``24-2'' (refer to

Hamilton Sundstrand Service Bulletin ERPS10AG-24-2 for further information).

(3) Actions done before the effective date of this AD according to Bombardier Service Bulletin 670BA-24-015, dated May 17, 2004, are considered acceptable for compliance with the corresponding actions specified in this AD, provided the ADG has not been replaced since those actions were done.

FAA AD Differences

Note 1: This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:

Page 26047

(1) Alternative Methods of Compliance (AMOCs): The Manager, New

York Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Fabio Buttitta, Aerospace

Engineer, Systems and Flight Test Branch, ANE-172, FAA, New York

Aircraft Certification Office, 1600 Stewart Avenue, Suite 410,

Westbury, New York 11590; telephone (516) 228-7303; fax (516) 794- 5531. Before using any approved AMOC on any airplane to which the

AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the

Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120- 0056.

Related Information

(h) Refer to Canadian Airworthiness Directive CF-2008-10, dated

February 5, 2008, and Bombardier Service Bulletin 670BA-24-015,

Revision A, dated December 18, 2006, for related information.

Issued in Renton, Washington, on April 25, 2008.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification

Service.

FR Doc. E8-10219 Filed 5-7-08; 8:45 am

BILLING CODE 4910-13-P