Airworthiness Directives: Bombardier Model CL 600 2C10 (Regional Jet Series 700, 701 & 702) Airplanes, etc.

Federal Register: August 5, 2009 (Volume 74, Number 149)

Proposed Rules

Page 38993-38995

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

DOCID:fr05au09-29

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration 14 CFR Part 39

Docket No. FAA-2009-0703; Directorate Identifier 2009-NM-093-AD

RIN 2120-AA64

Airworthiness Directives; Bombardier Model CL-600-2C10 (Regional

Jet Series 700, 701 & 702) Airplanes, Model CL-600-2D15 (Regional Jet

Series 705) Airplanes, and Model CL-600-2D24 (Regional Jet Series 900)

Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: There have been four reports of loose or detached main landing gear torque link apex pin locking plate and the locking plate retainer bolt. This condition could result in torque link apex pin disengagement, heavy vibration during landing, damage to main landing gear components and subsequent main landing gear collapse.

The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by September 4, 2009.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New

Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact

Bombardier, Inc., 400 Cote-Vertu Road West, Dorval, Qu[eacute]bec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; e-mail thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may review copies of the referenced service information at the FAA,

Transport Airplane Directorate, 1601 Lind Avenue SW., Renton,

Washington. For information on the availability of this material at the

FAA, call 425-227-1221 or 425-227-1152.

Examining the AD Docket

You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Pong Lee, Aerospace Engineer, Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft

Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New

York 11590; telephone (516) 228-7324; fax (516) 794-5531.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2009-0703;

Directorate Identifier 2009-NM-093-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We will post all comments we receive, without change, to http://

Page 38994

www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Transport Canada Civil Aviation (TCCA), which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF- 2009-20, dated May 1, 2009 (referred to after this as ``the MCAI''), to correct an unsafe condition for the specified products. The MCAI states:

There have been four reports of loose or detached main landing gear torque link apex pin locking plate and the locking plate retainer bolt. This condition could result in torque link apex pin disengagement, heavy vibration during landing, damage to main landing gear components and subsequent main landing gear collapse.

Investigation has determined that incorrect stack-up tolerances of the apex joint or improper installation of the locking plate and apex nut could result in torque link apex pin disengagement. This directive mandates [a one-time detailed] inspection of the torque link apex joint [for correct installation and damage, and corrective actions if necessary] and replacement of the torque link apex nut.

The corrective actions include re-installing parts that are not correctly installed and replacing damaged parts. You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Bombardier has issued Service Bulletin 670BA-32-019, Revision A, dated September 18, 2008. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of this Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences between this AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a note within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 361 products of U.S. registry. We also estimate that it would take about 4 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work-hour. Based on these figures, we estimate the cost of the proposed

AD on U.S. operators to be $115,520, or $320 per product.

Authority for this Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation

Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in

``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation: 1. Is not a ``significant regulatory action'' under Executive Order 12866; 2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR PART 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the

Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended] 2. The FAA amends Sec. 39.13 by adding the following new AD:

Bombardier, Inc. (Formerly Canadair): Docket No. FAA-2009-0703;

Directorate Identifier 2009-NM-093-AD.

Comments Due Date

(a) We must receive comments by September 4, 2009.

Affected ADs

(b) None.

Applicability

(c) This AD applies to the Bombardier airplanes identified in paragraphs (c)(1) and (c)(2) of this AD, certificated in any category.

(1) Model CL-600-2C10 (Regional Jet Series 700, 701 & 702) airplanes, serial numbers (S/Ns) 10003 and subsequent.

(2) Model CL-600-2D15 (Regional Jet Series 705) airplanes and

Model CL-600-2D24 (Regional Jet Series 900) airplanes, S/Ns 15001 and subsequent.

Subject

(d) Air Transport Association (ATA) of America Code 32: Landing gear.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

There have been four reports of loose or detached main landing gear torque link apex pin locking plate and the locking plate retainer bolt. This condition could result in torque link apex pin disengagement, heavy vibration during landing, damage to main landing gear components and subsequent main landing gear collapse.

Investigation has determined that incorrect stack-up tolerances of the apex joint or improper installation of the locking plate and apex nut could result in torque link apex pin disengagement. This directive mandates [a

Page 38995

one-time detailed] inspection of the torque link apex joint [for correct installation and damage, and corrective actions if necessary] and replacement of the torque link apex nut.

The corrective actions include re-installing parts that are not correctly installed and replacing damaged parts.

Actions and Compliance

(f) Unless already done, do the following actions.

(1) For Model CL-600-2C10 airplanes, S/Ns 10003 through 10223 inclusive; and Model CL-600-2D15 and Model CL-600-2D24 airplanes, S/

Ns 15001 through 15035 inclusive, 15038, 15039, and 15042: Within 900 flight hours after the effective date of this AD, perform a one- time detailed inspection and all applicable corrective actions on the torque link apex joint, in accordance with Part A of the

Accomplishment Instructions of Bombardier Service Bulletin 670BA-32- 019, Revision A, dated September 18, 2008, except as provided by paragraph (f)(5) of this AD. Do all applicable corrective actions before further flight.

(2) For Model CL-600-2C10 airplanes, S/Ns 10003 through 10239 inclusive; and Model CL-600-2D15 and CL-600-2D24 airplanes, S/Ns 15001 through 15057 inclusive: Within 4,500 flight hours after the effective date of this AD, replace or rework the apex nut, in accordance with Part B of the Accomplishment Instructions of

Bombardier Service Bulletin 670BA-32-019, Revision A, dated

September 18, 2008.

(3) As of the effective date of this AD, no person may install, on any airplane, a replacement MLG shock strut assembly identified in paragraph (f)(3)(i) or (f)(3)(ii) of this AD, unless it has been reworked in accordance with Part B of the Accomplishment

Instructions of Bombardier Service Bulletin 670BA-32-019, Revision

A, dated September 18, 2008.

(i) Part number (P/N) 49000-11 through 49000-22 inclusive, and with a serial number in the range of S/N 0001 through 0284 inclusive

(the serial number can start with ``MA,'' ``MAL,'' or ``MA-'').

(ii) P/N 49050-5 through 49050-10 inclusive, and with a serial number in the range of S/N 1001 through 1114 inclusive (the serial number can start with ``MA,'' ``MAL,'' or ``MA-'').

(4) Inspections, corrective actions, replacements, and rework accomplished before the effective date of this AD in accordance with

Bombardier Service Bulletin 670BA-32-019, dated March 16, 2006, are considered acceptable for compliance with the corresponding actions specified in this AD.

(5) The inspections specified in paragraph (f)(1) of this AD are not required if the actions specified in paragraph (f)(2) of this AD have already been accomplished; or if Bombardier Repair Engineering

Order 670-32-11-0022, dated October 22, 2005; or Goodrich Service

Concession Request SCR 0056-05, dated October 22, 2005; has been incorporated.

FAA AD Differences

Note 1: This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, New

York Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Pong Lee, Aerospace

Engineer, Airframe and Mechanical Systems Branch, ANE-171, FAA, New

York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410,

Westbury, New York 11590; telephone (516) 228-7324; fax (516) 794- 5531. Before using any approved AMOC on any airplane to which the

AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office.

The AMOC approval letter must specifically reference this AD.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the

Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120- 0056.

(h) Special Flight Permits: Special flight permits, as described in Section 21.197 and Section 21.199 of the Federal Aviation

Regulations (14 CFR 21.197 and 21.199), are not allowed.

Related Information

(i) Refer to MCAI Canadian Airworthiness Directive CF-2009-20, dated May 1, 2009; and Bombardier Service Bulletin 670BA-32-019,

Revision A, dated September 18, 2008; for related information.

Issued in Renton, Washington, on July 28, 2009.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification

Service.

FR Doc. E9-18731 Filed 8-4-09; 8:45 am

BILLING CODE 4910-13-P