Airworthiness Directives: Fokker Services B.V. Model F.28 Mark 0070 and 0100 Airplanes

Federal Register: May 18, 2010 (Volume 75, Number 95)

Proposed Rules

Page 27668-27670

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

DOCID:fr18my10-14

Page 27668

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration 14 CFR Part 39

Docket No. FAA-2010-0516; Directorate Identifier 2009-NM-251-AD

RIN 2120-AA64

Airworthiness Directives; Fokker Services B.V. Model F.28 Mark 0070 and 0100 Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

When preparing for landing, the flight crew of a F28 Mark 0100

(Fokker 100) aeroplane observed a main landing gear (MLG) unsafe indication after landing gear down selection. * * * [T]he right (RH)

MLG was partly extended and the left (LH) MLG door was open but without the MLG being extended. * * *

Subsequent investigation revealed that the cause of the MLG extension problem was the (partially) blocked hydraulic return line from the MLG selector valve by pieces of hard plastic. These were identified as parts of the poppet seat of PBSOV [parking brake shut- off valve] Part Number (P/N) 70379. * * *

This condition, if not detected and corrected, could lead to further events where the MLG fails to extend, possibly resulting in loss of control of the aeroplane during landing.

* * * * *

The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES: We must receive comments on this proposed AD by July 2, 2010.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue, SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New

Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact

Fokker Services B.V., Technical Services Dept., P.O. Box 231, 2150 AE

Nieuw-Vennep, the Netherlands; telephone +31 (0)252-627-350; fax +31

(0)252-627-211; e-mail technicalservices.fokkerservices@stork.com;

Internet http://www.myfokkerfleet.com. You may review copies of the referenced service information at the FAA, Transport Airplane

Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221.

Examining the AD Docket

You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Tom Rodriguez, Aerospace Engineer,

International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2010-0516;

Directorate Identifier 2009-NM-251-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We have lengthened the 30-day comment period for proposed ADs that address MCAI originated by aviation authorities of other countries to provide adequate time for interested parties to submit comments. The comment period for these proposed ADs is now typically 45 days, which is consistent with the comment period for domestic transport ADs.

We will post all comments we receive, without change, to http:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

The European Aviation Safety Agency (EASA), which is the Technical

Agent for the Member States of the European Community, has issued EASA

Airworthiness Directive 2009-0220, dated October 14, 2009 (referred to after this as ``the MCAI''), to correct an unsafe condition for the specified products. The MCAI states:

When preparing for landing, the flight crew of a F28 Mark 0100

(Fokker 100) aeroplane observed a main landing gear (MLG) unsafe indication after landing gear down selection. The approach was aborted and the landing gear unsafe procedure was accomplished. As this did not produce the desired effect, a low pass was performed and the control tower confirmed that the right (RH) MLG was partly extended and the left (LH) MLG door was open but without the MLG being extended. Eventually the aeroplane landed with partly extended landing gear, without resulting in serious injuries to the occupants.

Subsequent investigation revealed that the cause of the MLG extension problem was the (partially) blocked hydraulic return line from the MLG selector valve by pieces of hard plastic. These were identified as parts of the poppet seat of PBSOV [parking brake shut- off valve] Part Number (P/N) 70379. The PBSOV installed on the incident aeroplane was a modified version of P/N 70379, identified by suffix ``A'' behind the serial number on the identification plate. This modification was introduced by Eaton, the valve manufacturer, with Eaton Service Bulletin (SB) 70379-32-01 and includes replacement of the original poppet with clamped hard plastic seat by an improved poppet assembly with screwed-on seat.

When the affected valve was opened, it was confirmed that it contained the improved poppet assembly. The poppet seat fragments found in the return system therefore originated from a previously installed (pre SB 70379-32-01) P/N 70379 PBSOV and must have been present in the return/pressure line prior to installation of the modified PBSOV.

This condition, if not detected and corrected, could lead to further events where the MLG fails to extend, possibly resulting in loss of control of the aeroplane during landing.

For the reasons described above, this AD requires the [detailed] inspection of the associated hydraulic lines, irrespective what type

PBSOV is installed, removal of contamination in the system, if any, and replacement of each unmodified PBSOV with a modified unit. This

AD also prohibits, after installation of a modified PBSOV on an aeroplane, re-installation of an unmodified PBSOV on that aeroplane.

You may obtain further information by examining the MCAI in the AD docket.

Page 27669

Relevant Service Information

Fokker Services B.V. has issued Service Bulletin SBF100-32-159, dated October 6, 2009. Eaton Aerospace has issued Service Bulletin 70379-32-01, dated September 15, 2001. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 6 products of U.S. registry. We also estimate that it would take about 4 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of the proposed

AD on U.S. operators to be $2,040, or $340 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation

Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in

``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation: 1. Is not a ``significant regulatory action'' under Executive Order 12866; 2. Is not a ``significant rule'' under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and 3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the

Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended] 2. The FAA amends Sec. 39.13 by adding the following new AD:

Fokker Services B.V.: Docket No. FAA-2010-0516; Directorate

Identifier 2009-NM-251-AD.

Comments Due Date

(a) We must receive comments by July 2, 2010.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes, certificated in any category, all serial numbers.

Subject

(d) Air Transport Association (ATA) of America Code 32: Landing

Gear.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

When preparing for landing, the flight crew of a F28 Mark 0100

(Fokker 100) aeroplane observed a main landing gear (MLG) unsafe indication after landing gear down selection. * * * [T]he right (RH)

MLG was partly extended and the left (LH) MLG door was open but without the MLG being extended. * * *

Subsequent investigation revealed that the cause of the MLG extension problem was the (partially) blocked hydraulic return line from the MLG selector valve by pieces of hard plastic. These were identified as parts of the poppet seat of PBSOV [parking brake shut- off valve] Part Number (P/N) 70379. * * *

This condition, if not detected and corrected, could lead to further events where the MLG fails to extend, possibly resulting in loss of control of the aeroplane during landing.

* * * * *

Compliance

(f) You are responsible for having the actions required by this

AD performed within the compliance times specified, unless the actions have already been done.

Actions

(g) Do the following actions.

(1) Within 30 days after the effective date of this AD, do a detailed inspection of the hydraulic lines associated with the PBSOV for contamination in the system (the presence of pieces of material from the poppet seat of an unmodified PBSOV having P/N 70379). If any contamination is found, before further flight, remove the contamination, in accordance with Part 1 of the Accomplishment

Instructions of Fokker Service Bulletin SBF100-32-159, dated October 6, 2009.

(2) Within 18 months after the effective date of this AD, re- inspect the hydraulic lines and do all applicable corrective actions as required by paragraph (g)(1) of this AD, and replace the unmodified PBSOV having P/N 70379, with a modified PBSOV having P/N 70379 having the suffix ``A'' behind the serial number on the identification plate, in accordance with Part 2 of the

Accomplishment Instructions of Fokker Service Bulletin SBF100-32- 159, dated October 6, 2009.

(3) After accomplishing paragraph (g)(2) of this AD, do not install any unmodified

Page 27670

PBSOV having P/N 70379, unless the PBSOV having P/N 70379 has been modified, having the suffix ``A'' behind the serial number on the identification plate, in accordance with the Accomplishment

Instructions of Eaton Service Bulletin 70379-32-01, dated September 15, 2001.

FAA AD Differences

Note 1: This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(h) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager,

International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tom

Rodriguez, Aerospace Engineer, International Branch, ANM-116,

Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton,

Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149.

Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office.

The AMOC approval letter must specifically reference this AD.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44

U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned

OMB Control Number 2120-0056.

Related Information

(i) Refer to MCAI European Aviation Safety Agency Airworthiness

Directive 2009-0220, dated October 14, 2009; Fokker Service Bulletin

SBF100-32-159, dated October 6, 2009; and Eaton Service Bulletin 70379-32-01, dated September 15, 2001; for related information.

Issued in Renton, Washington, on May 7, 2010.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification

Service.

FR Doc. 2010-11890 Filed 5-17-10; 8:45 am

BILLING CODE 4910-13-P