Airworthiness Directives: Stemme GmbH & Co. KG Models S10 and S10 V Gliders

Federal Register: November 6, 2008 (Volume 73, Number 216)

Rules and Regulations

Page 65979-65981

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

DOCID:fr06no08-7

Page 65979

DEPARTMENT OF TRANSPORTATION

Federal Aviation Administration 14 CFR Part 39

Docket No. FAA-2008-1161; Directorate Identifier 2008-CE-067-AD;

Amendment 39-15726; AD 2008-23-05

RIN 2120-AA64

Airworthiness Directives; Stemme GmbH & Co. KG Models S10 and

S10-V Gliders

AGENCY: Federal Aviation Administration (FAA), DOT.

ACTION: Final rule; request for comments.

SUMMARY: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

Investigations performed following a report about a fuel leakage in a Stemme S10-V powered-sailplane revealed that some fuel lines fabricated between March 2008 and May 2008, after the introduction of a new pressing tool, present a manufacturing defect which could lead to the puncture of the fuel lines.

This AD requires actions that are intended to address the unsafe condition described in the MCAI.

DATES: This AD becomes effective November 26, 2008.

On November 26, 2008 the Director of the Federal Register approved the incorporation by reference of certain publications listed in this

AD.

We must receive comments on this AD by December 8, 2008.

ADDRESSES: You may send comments by any of the following methods:

Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the instructions for submitting comments.

Fax: (202) 493-2251.

Mail: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue, SE., Washington, DC 20590.

Hand Delivery: U.S. Department of Transportation, Docket

Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New

Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,

Monday through Friday, except Federal holidays.

Examining the AD Docket

You may examine the AD docket on the Internet at http:// www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

FOR FURTHER INFORMATION CONTACT: Greg Davison, Glider Program Manager, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4130; fax: (816) 329-4090.

SUPPLEMENTARY INFORMATION:

Discussion

The European Aviation Safety Agency (EASA), which is the Technical

Agent for the Member States of the European Community, has issued AD

No.: 2008-0186-E, dated October 9, 2008 (referred to after this as

``the MCAI''), to correct an unsafe condition for the specified products. The MCAI states:

Investigations performed following a report about a fuel leakage in a Stemme S10-V powered-sailplane revealed that some fuel lines fabricated between March 2008 and May 2008, after the introduction of a new pressing tool, present a manufacturing defect which could lead to the puncture of the fuel lines.

For the reason stated above, this Airworthiness Directive (AD) mandates, as an initial phase, repetitive inspections of the fuel lines until their replacement, by new ones which conform to the approved original specifications, is implemented as a final fix.

You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Stemme GmbH & Co. KG has issued Stemme F & D Service Bulletin A31- 10-084 Am.-Index: 01.a, dated October 1, 2008. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of the AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with this State of Design Authority, they have notified us of the unsafe condition described in the MCAI and service information referenced above. We are issuing this AD because we evaluated all information provided by the State of Design Authority and determined the unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the

AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have required different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are described in a separate paragraph of the AD. These requirements take precedence over those copied from the MCAI.

FAA's Determination of the Effective Date

An unsafe condition exists that requires the immediate adoption of this AD. The FAA has found that the risk to the flying public justifies waiving notice and comment prior to adoption of this rule because investigations performed following a report about a fuel leakage in a

Stemme S10-V powered sailplane revealed that some fuel lines fabricated between March 2008 and May 2008, after the introduction of a new pressing tool, present a manufacturing defect which could lead to the puncture of the fuel lines. Therefore, we determined that notice and opportunity for public comment before issuing this AD are impracticable and that good cause exists for making this amendment effective in fewer than 30 days.

Comments Invited

This AD is a final rule that involves requirements affecting flight safety, and we did not precede it by notice and opportunity for public comment. We invite you to send any written relevant data, views, or arguments about this AD. Send your comments to an address listed under the ADDRESSES section. Include ``Docket No. FAA-2008-1161; Directorate

Identifier 2008-CE-067-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this AD. We will consider all comments received by the closing date and may amend this AD because of those comments.

Page 65980

We will post all comments we receive, without change, to http:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this AD.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. ``Subtitle VII: Aviation

Programs,'' describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in

``Subtitle VII, Part A, Subpart III, Section 44701: General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that this AD:

(1) Is not a ``significant regulatory action'' under Executive

Order 12866;

(2) Is not a ``significant rule'' under DOT Regulatory Policies and

Procedures (44 FR 11034, February 26, 1979); and

(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment 0

Accordingly, under the authority delegated to me by the Administrator, the FAA amends14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding the following new AD: 2008-23-05 Stemme GmbH & Co. KG: Amendment 39-15726; Docket No. FAA- 2008-1161; Directorate Identifier 2008-CE-067-AD.

Effective Date

(a) This airworthiness directive (AD) becomes effective November 26, 2008.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Models S10 and S10-V gliders, serial numbers 10-32, 10-53, 14-025, and 14-027, certificated in any category.

Subject

(d) Air Transport Association of America (ATA) Code 73: Engine

Fuel & Control.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

``Investigations performed following a report about a fuel leakage in a Stemme S10-V powered-sailplane revealed that some fuel lines fabricated between March 2008 and May 2008, after the introduction of a new pressing tool, present a manufacturing defect which could lead to the puncture of the fuel lines.

``For the reason stated above, this Airworthiness Directive (AD) mandates, as an initial phase, repetitive inspections of the fuel lines until their replacement, by new ones which conform to the approved original specifications, is implemented as a final fix.''

Actions and Compliance

(f) Unless already done, do the following actions:

(1) Before every flight after November 26, 2008 (the effective date of this AD) until accomplishment of paragraph (f)(2) of this

AD, inspect the fuel lines in the engine compartment (pressed lines) following Stemme F & D Service Bulletin A31-10-084 Am.-Index: 01.a, dated October 1, 2008.

(2) Before further flight where any leakage is found as a result of any inspection required in paragraph (f)(1) of this AD or within the next 25 days after November 26, 2008 (the effective date of this

AD), whichever occurs first, replace all the fuel lines in the engine compartment (pressed lines) following Stemme F & D Service

Bulletin A31-10-084 Am.-Index: 01.a, dated October 1, 2008.

Replacement of all fuel lines in the engine compartment (pressed lines) terminates the repetitive inspection requirement of paragraph

(f)(1) of this AD.

FAA AD Differences

Note: This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager,

Standards Office, FAA, has the authority to approve AMOCs for this

AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Greg Davison, Glider Program Manager, FAA,

Small Airplane Directorate, 901 Locust, Room 301, Kansas City,

Missouri 64106; telephone: (816) 329-4130; fax: (816) 329-4090.

Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA

Flight Standards District Office (FSDO), or lacking a PI, your local

FSDO.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered

FAA-approved if they are approved by the State of Design Authority

(or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44

U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned

OMB Control Number 2120-0056.

Related Information

(h) Refer to European Aviation Safety Agency (EASA) AD No.: 2008-0186-E, dated October 9, 2008, and Stemme F & D Service

Bulletin A31-10-084 Am.-Index: 01.a, dated October 1, 2008, for related information.

Material Incorporated by Reference

(i) You must use Stemme F & D Service Bulletin A31-10-084 Am.-

Index: 01.a, dated October 1, 2008, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5

U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact

Stemme GmbH & Co. KG, Flugplatzstrae F2, Nr. 7, D-15344 Strausberg,

Germany; telephone: +49-33-41-3612-0; fax: +49-33-41-3612-30;

Internet: http://www.stemme.de/daten/d/service/a3110084_01a.pdf ; e-mail: P.Ellwanger@stemme.de.

(3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration

(NARA). For information on the availability of this material at

NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_ register/code_of_federal_regulations/ibr_locations.html.

Page 65981

Issued in Kansas City, Missouri, on October 28, 2008.

James E. Jackson,

Acting Manager, Small Airplane Directorate, Aircraft Certification

Service.

FR Doc. E8-26235 Filed 11-5-08; 8:45 am

BILLING CODE 4910-13-P