Energy Labeling Rule
| Published date | 30 October 2019 |
| Citation | 84 FR 58026 |
| Record Number | 2019-23505 |
| Section | Rules and Regulations |
| Court | Federal Trade Commission |
Federal Register, Volume 84 Issue 210 (Wednesday, October 30, 2019)
[Federal Register Volume 84, Number 210 (Wednesday, October 30, 2019)]
[Rules and Regulations]
[Pages 58026-58045]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2019-23505]
=======================================================================
-----------------------------------------------------------------------
FEDERAL TRADE COMMISSION
16 CFR Part 305
[3084-AB15]
Energy Labeling Rule
AGENCY: Federal Trade Commission (``FTC'' or ``Commission'').
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The Commission amends the Energy Labeling Rule (``Rule'') to
make the Rule easier to use by reorganizing several sections, amending
language to increase clarity, eliminating several obsolete provisions,
and making minor corrections.
DATES: The amendments are effective on November 29, 2019.
ADDRESSES: Copies of this document are available on the Commission's
website, www.ftc.gov.
FOR FURTHER INFORMATION CONTACT: Hampton Newsome (202-326-2889),
Attorney, Division of Enforcement, Bureau of Consumer Protection,
Federal Trade Commission, Room CC-9528, 600 Pennsylvania Avenue NW,
Washington, DC 20580.
SUPPLEMENTARY INFORMATION:
I. Background
The Commission issued the Energy Labeling Rule (``Rule'') in
1979,\1\ pursuant to the Energy Policy and Conservation Act of 1975
(``EPCA'').\2\ The Rule requires energy labeling for major home
appliances and other consumer products to help consumers compare
competing models. It also contains labeling requirements for
refrigerators, refrigerator-freezers, freezers, dishwashers, water
heaters, clothes washers, room air conditioners, furnaces, central air
conditioners, heat pumps, plumbing products, lighting products, ceiling
fans, and televisions.
---------------------------------------------------------------------------
\1\ 44 FR 66466 (Nov. 19, 1979).
\2\ 42 U.S.C. 6294. EPCA also requires the Department of Energy
(DOE) to develop test procedures that measure how much energy
appliances use and to determine the representative average cost a
consumer pays for different types of energy.
---------------------------------------------------------------------------
The Rule requires manufacturers to attach yellow EnergyGuide labels
to
[[Page 58027]]
many of the covered products and prohibits retailers from removing
these labels or rendering them illegible. In addition, it directs
sellers, including retailers, to post label information on websites and
in paper catalogs from which consumers can order products. EnergyGuide
labels for most covered products contain three key disclosures:
Estimated annual energy cost, a energy consumption or energy efficiency
rating as determined by DOE test procedures, and a comparability range
displaying the highest and lowest energy costs or efficiency ratings
for all similar models. The Rule requires marketers to use national
average costs for applicable energy sources (e.g., electricity, natural
gas, oil) as calculated by DOE in all cost calculations. Under the
Rule, the Commission periodically updates comparability range and
annual energy cost information based on manufacturer data submitted
pursuant to the Rule's reporting requirements.\3\
---------------------------------------------------------------------------
\3\ 16 CFR 305.10.
---------------------------------------------------------------------------
II. Notice of Proposed Rulemaking
In March 2019, the Commission published a Notice of Proposed
Rulemaking (``NPRM'') (84 FR 9261 (Mar. 14, 2019)) seeking comments on
a series of proposed amendments intended to improve the Rule's
organization and clarity. The Commission proposed such changes because
various amendments over the years had caused some sections to become
lengthy and difficult to navigate.
The NPRM sought comment on three general categories of proposed
Rule changes. First, the proposed amendments divided current section
305.3 (Description of covered products), which lists the specific
product types (e.g., clothes washers, LED lamps) covered by the Rule,
into four different provisions organized by general product category
(i.e., appliances, furnaces and central air conditioners, lighting, and
plumbing).\4\ As the Commission explained in the NPRM, these changes
should make it easier for stakeholders to identify relevant covered
products, particularly for categories such as lighting, which contain
several different product types and exemptions.
---------------------------------------------------------------------------
\4\ The four proposed product category sections were: Sec.
305.3 (Description of appliances and consumer electronics), Sec.
305.4 (Description of furnaces and central air conditioners), Sec.
305.5 (Description of lighting products), and Sec. 305.6
(Description of plumbing products).
---------------------------------------------------------------------------
Second, the amendments proposed in the NPRM divided section 305.11
into several different sections to make it easier to identify the
labeling requirements applicable to specific products. Current section
305.11 addresses the label format and content for several appliances
through a long list of instructions and exceptions. The proposed new
provisions included a single section for general layout and formatting,
plus six additional sections covering label content for refrigerators,
clothes washers, dishwashers, water heaters, room air conditioners, and
pool heaters.\5\
---------------------------------------------------------------------------
\5\ Under the proposal, the revised sections would include:
Sec. 305.13 (Layout, format, and placement of labels for all
products), Sec. 305.14 (Label content for refrigerators,
refrigerator-freezers, and freezers), Sec. 305.15 (Label content
for clothes washers), Sec. 305.16 (Label content for dishwashers),
Sec. 305.17 (Label content for water heaters), Sec. 305.18 (Label
content for room air conditioners), and Sec. 305.19 (Label content
for pool heaters). The proposed amendments renumbered but otherwise
retained the current labeling sections for heating and cooling
equipment, ceiling fans, lighting products, plumbing products, and
televisions.
---------------------------------------------------------------------------
Third, the proposed amendments removed obsolete references to
products produced decades ago (e.g., exemptions for plumbing products
produced before 1994).\6\ As noted in the NPRM, such provisions are no
longer necessary because units produced before those dates are unlikely
to be sold as new today. Finally, the proposed amendments made several
minor changes to eliminate unnecessary cross references and made minor
corrections.
---------------------------------------------------------------------------
\6\ The proposed amendments also removed an obsolete provision
(Sec. 305.4(d)(3)) related to industry petitions for revised energy
representations made in response to new or amended DOE test
procedures. At the time of the Rule's initial publication, the
Commission had responsibility for reviewing such petitions under
EPCA. However, DOE has that responsibility under the current
statute, making this particular provision no longer operable. See 42
U.S.C. 6293(c)(3).
---------------------------------------------------------------------------
The Commission sought comment on these proposed amendments and any
suggestions to clarify, correct, improve, or otherwise make the Rule
easier to use. The NPRM stated that the Commission was not seeking
comments on substantive changes to the Rule, such as modifications to
label content, disclosure requirements, or product coverage.
III. Comments Received and Final Amendments
In response to the NPRM, the Commission received four comments.\7\
All of them supported (or did not object to) the Commission's proposed
amendments. AHAM, for example, stated that the revisions ``streamline
some areas and reduce redundancy.'' AHRI supported the effort ``to
reorganize and clarify'' the Rule. In addition, commenter Drakontaidis
stated that changes would make the rule much ``easier to comprehend and
more accessible to'' both businesses and consumers. Given the comments,
the Commission issues the amendments as proposed. In addition, some
commenters offered suggestions not included in the NPRM, some of which
the Commission includes in the final amendments as discussed below.
---------------------------------------------------------------------------
\7\ Air-Conditioning, Heating, and Refrigeration Institute
(AHRI), Drakontaidis, Korpal, and Association of Home Appliance
Manufacturers (AHAM) submitted comments. The comments are available
at https://www.regulations.gov/docket?D=FTC-2019-0015.
---------------------------------------------------------------------------
First, AHAM recommended a small change to refrigerator-freezer
model descriptions in the Appendix A tables (``Without Through-the-Door
Ice'') to match the sample refrigerator label (``No through-the-door
ice'').\8\ Second, AHAM, along with commenter Korpal, noted the need to
adjust the size of the ENERGY STAR logo on the sample labels in
Appendix L.\9\ Third, AHRI recommended the Commission allow
manufacturers to use a larger text size for part or publication numbers
used on EnergyGuide labels (as allowed by the current Rule) to ensure
manufacturers can match labels to the correct models. The final
amendments contain these minor corrections and changes.\10\ To avoid
any burden associated with these minor label amendments, manufacturers
may wait to implement any necessary changes until their next label
print run. If manufacturers have any questions
[[Page 58028]]
about the timing of such changes, they may contact FTC staff for
guidance.\11\
---------------------------------------------------------------------------
\8\ The Rule does not mandate specific language for the product
descriptions at top, left of label. However, such descriptions may
not include extraneous features beyond those identified in the Rule
itself. See 83 FR 7593, 7595 (Feb. 22, 2018) and 81 FR 63634, 63639,
n. 39 (Sept. 15, 2016).
\9\ The amendments make five additional minor corrections and
updates: (1) Minor adjustments to the font size instructions on the
refrigerator prototype label in Appendix L (``Estimated Yearly
Electricity Use'' and ``ftc.gov/energy'') to match the sample itself
and the online template; (2) corrections to line thicknesses on the
Clothes Washer prototype and sample labels in Appendix L (does not
affect the template label); (3) replacement of references to ANSI
standards in the fluorescent and incandescent lamp definitions with
appropriate references to EPCA; (4) updates to cross references in
Appendices K1 and K2, and in the sample Lighting Facts labels in
Appendix L; and (5) a clarification in new section 305.13 that
labels affixed to boxes for certain products may have a yellow or a
neutral contrasting background. In addition, FTC staff has corrected
several issues AHAM identified with the online label templates
posted on the FTC website for the convenience of manufacturers. See
https://www.ftc.gov/tips-advice/business-center/guidance/energyguide-labels-templates-manufacturers.
\10\ The amendments allow up to 12-point text for part or
publication numbers on appliances, furnaces, and central air
conditioner labels in newly designated sections 305.14-305.20. Given
the size of such labels, the change should have no effect on
consumer use or understanding. The amendments do not alter
requirements for smaller EnergyGuide labels (e.g., television
labels) because larger font sizes may crowd those labels.
\11\ The Commission finds good cause for implementing these
various minor technical corrections and changes without further
notice and comment. See 5 U.S.C. 553(b)(3)(B); 16 CFR 1.26(b).
---------------------------------------------------------------------------
AHAM also requested an amendment to allow manufacturers to attach
hangtags on clothes washer exteriors. The Commission declines to make
this change as part of this proceeding. The current Rule does not allow
hangtags on the outside of products due to concerns raised in an
earlier proceeding about the durability of such tags, and AHAM has not
indicated why such concerns are no longer valid.\12\ Furthermore, such
an amendment falls outside of the scope of this rulemaking. If
manufacturers wish to place labels on the outside of clothes washers,
they may use adhesive labels under the current Rule.\13\
---------------------------------------------------------------------------
\12\ 72 FR 49947, 49961 (Aug. 29, 2007).
\13\ See newly designated section 305.13.
---------------------------------------------------------------------------
Finally, AHRI, which expressed support for Commissioner Wilson's
dissenting statement on the NPRM (84 FR at 9272-73), recommended a
broader, substantive rule review aimed at reducing regulatory burden.
Specifically, AHRI urged elimination of physical labels for central air
conditioners, heat pumps, and furnaces. According to AHRI, the large
majority of those products are not purchased off the shelves at retail
stores, and consumers generally do not view them before installation.
The Commission is not considering such changes at this time because
they fall outside of the scope of this rulemaking, which, as explained
in the NPRM, is limited to improving the Rule's organization and making
minor modifications and corrections. In addition, the Commission
considered similar concerns in the past and concluded that the labels
on such equipment help consumers in both their use of existing
equipment and their purchasing decisions for replacement products.\14\
The Commission may consider AHRI's concerns and other broad issues in
future proceedings.\15\
---------------------------------------------------------------------------
\14\ 72 FR 49947, 49956 (Aug. 29, 2007).
\15\ Commenter Drakontaidis suggested that the Commission create
a summary section in the Rule ``as a sort of refresher for anything
that might be missed by the reader.'' Because the amendments already
shorten the Rule, such a summary does not appear necessary.
---------------------------------------------------------------------------
IV. Paperwork Reduction Act
The current Rule contains recordkeeping, disclosure, testing, and
reporting requirements that constitute information collection
requirements as defined by 5 CFR 1320.3(c), the definitional provision
within the Office of Management and Budget (OMB) regulations that
implement the Paperwork Reduction Act. OMB has approved the Rule's
existing information collection requirements through November 30, 2019
(OMB Control No. 3084-0069). The amendments do not change the substance
or frequency of the recordkeeping, disclosure, or reporting
requirements and therefore do not require further OMB clearance.
V. Regulatory Flexibility Act
The provisions of the Regulatory Flexibility Act relating to a
Regulatory Flexibility Act analysis (5 U.S.C. 603-604) are not
applicable to this proceeding because the proposed amendments do not
impose any new or different obligations on entities regulated by the
Energy Labeling Rule. As explained elsewhere in this document, the
amendments do not change the substance or frequency of the
recordkeeping, disclosure, or reporting requirements. Thus, the
amendments will not have a ``significant economic impact on a
substantial number of small entities.'' 5 U.S.C. 605. The Commission
has, therefore, concluded that a regulatory flexibility analysis is not
necessary, and certifies, under 5 U.S.C. 605(b), that the amendments
will not have a significant economic impact on a substantial number of
small entities. This rulemaking document constitutes notice of the
above certification and statement to the Small Business Administration
required under 5 U.S.C. 605(b).
List of Subjects in 16 CFR Part 305
Advertising, Energy conservation, Household appliances, Labeling,
Reporting and recordkeeping requirements.
Final Rule Language
For the reasons set out above, the Commission amends 16 CFR part
305 as follows:
PART 305--ENERGY AND WATER USE LABELING FOR CONSUMER PRODUCTS UNDER
THE ENERGY POLICY AND CONSERVATION ACT (``ENERGY LABELING RULE'')
0
1. The authority citation for part 305 continues to read as follows:
Authority: 42 U.S.C. 6294.
0
2. Amend Sec. 305.2, by revising paragraphs (n), (q), and (aa) to read
as follows:
Sec. 305.2 Definitions.
* * * * *
(n) Covered product means any consumer product or consumer
appliance product described in Sec. 305.3, Sec. 305.4, Sec. 305.5,
or Sec. 305.6 of this part.
* * * * *
(q) Estimated annual energy consumption and estimated annual
operating or energy cost--(1) Estimated annual energy consumption means
the energy or (for plumbing products) water that is likely to be
consumed annually in representative use of a consumer product, as
determined in accordance with tests prescribed under section 323 of the
Act (42 U.S.C. 6293).
(i) Kilowatt-hour use per year, or kWh/yr., means estimated annual
energy consumption expressed in kilowatt-hours of electricity.
(ii) Therm use per year, or therms/yr., means estimated annual
energy consumption expressed in therms of natural gas.
(iii) Gallon use per year, or gallons/yr., means estimated annual
energy consumption expressed in gallons of propane or No. 2 heating
oil.
(2) Estimated annual operating or energy cost means the aggregate
retail cost of the energy that is likely to be consumed annually in
representative use of a consumer product, as determined in accordance
with tests prescribed under section 323 of the Act (42 U.S.C. 6293).
* * * * *
(aa) New covered product means a covered product the title of which
has not passed to a purchaser who buys the product for purposes other
than resale or leasing for a period in excess of one year.
* * * * *
0
3. Revise Sec. 305.3 to read as follows:
Sec. 305.3 Description of appliances and consumer electronics.
(a) Refrigerators and refrigerator-freezers--(1) Electric
refrigerator means a cabinet designed for the refrigerated storage of
food, designed to be capable of achieving storage temperatures above 32
[deg]F (0 [deg]C) and below 39 [deg]F (3.9 [deg]C), and having a source
of refrigeration requiring single phase, alternating current electric
energy input only. An electric refrigerator may include a compartment
for the freezing and storage of food at temperatures below 32 [deg]F (0
[deg]C), but does not provide a separate low temperature compartment
designed for the freezing and storage of food at temperatures below 8
[deg]F (-13.3 [deg]C).
(2) Electric refrigerator-freezer means a cabinet which consists of
two or more compartments with at least one of the compartments designed
for the refrigerated storage of food and designed to be capable of
achieving storage
[[Page 58029]]
temperatures above 32 [deg]F (0 [deg]C) and below 39 [deg]F (3.9
[deg]C), and with at least one of the compartments designed for the
freezing and storage of food at temperatures below 8 [deg]F (-13.3
[deg]C) which may be adjusted by the user to a temperature of 0 [deg]F
(-17.8 [deg]C) or below. The source of refrigeration requires single
phase, alternating current electric energy input only.
(b) Freezer means a cabinet designed as a unit for the freezing and
storage of food at temperatures of 0 [deg]F or below, and having a
source of refrigeration requiring single phase, alternating current
electric energy input only.
(c) Dishwasher means a cabinet-like appliance which, with the aid
of water and detergent, washes, rinses, and dries (when a drying
process is included) dishware, glassware, eating utensils and most
cooking utensils by chemical, mechanical, and/or electrical means and
discharges to the plumbing drainage system.
(1) Water heating dishwasher means a dishwasher which is designed
for heating cold inlet water (nominal 50 [deg]F) or a dishwasher for
which the manufacturer recommends operation with a nominal inlet water
temperature of 120 [deg]F and may operate at either of these inlet
water temperatures by providing internal water heating to above 120
[deg]F in at least one wash phase of the normal cycle.
(2) [Reserved]
(d) Water heater means a product which utilizes oil, gas, or
electricity to heat potable water for use outside the heater upon
demand, including--
(1) Storage type units which heat and store water at a
thermostatically controlled temperature, including gas storage water
heaters with an input of 75,000 Btu per hour or less, oil storage water
heaters with an input of 105,000 Btu per hour or less, and electric
storage water heaters with an input of 12 kilowatts or less;
(2) Instantaneous type units that heat water but contain no more
than one gallon of water per 4,000 Btu per hour of input, including gas
instantaneous water heaters with an input of 200,000 Btu per hour or
less, oil instantaneous water heaters with an input of 210,000 Btu per
hour or less, and electric instantaneous water heaters with an input of
12 kilowatts or less; and
(3) Heat pump type units, with a maximum current rating of 24
amperes at a voltage no greater than 250 volts, which are products
designed to transfer thermal energy from one temperature level to a
higher temperature level for the purpose of heating water, including
all ancillary equipment such as fans, storage tanks, pumps, or controls
necessary for the device to perform its function.
(e) Room air conditioner means a consumer product, other than a
packaged terminal air conditioner, which is powered by a single phase
electric current and which is an encased assembly designed as a unit
for mounting in a window or through the wall for the purpose of
providing delivery of conditioned air to an enclosed space. It includes
a prime source of refrigeration and may include a means for ventilating
and heating.
(f) Clothes washer means a consumer product designed to clean
clothes, utilizing a water solution of soap and/or detergent and
mechanical agitation or other movement, and must be one of the
following classes: Automatic clothes washers, semi-automatic clothes
washers, and other clothes washers.
(1) Automatic clothes washer means a class of clothes washer which
has a control system capable of scheduling a pre-selected combination
of operations, such as regulation of water fill level, and performance
of wash, rinse, drain and spin functions, without the need for the user
to intervene subsequent to the initiation of machine operation. Some
models may require user intervention to initiate these different
segments of the cycle after the machine has begun operation, but they
do not require the user to intervene to regulate the water temperature
by adjusting the external water faucet valves.
(2) Semi-automatic clothes washer means a class of clothes washer
that is the same as an automatic clothes washer except that the user
must intervene to regulate the water temperature by adjusting the
external water faucet valves.
(3) Other clothes washer means a class of clothes washer that is
not an automatic or semi-automatic clothes washer.
(g) Ceiling fan means a nonportable device that is suspended from a
ceiling for circulating air via the rotation of fan blades, excluding
large-diameter and high-speed small diameter fans as defined in
appendix U of subpart B of 10 CFR part 430. The requirements of this
part are otherwise limited to those ceiling fans for which the
Department of Energy has adopted and published test procedures for
measuring energy usage.
(h) Television means a product that is designed to produce dynamic
video, contains an internal TV tuner encased within the product
housing, and is capable of receiving dynamic visual content from wired
or wireless sources including but not limited to: Broadcast and similar
services for terrestrial, cable, satellite, and/or broadband
transmission of analog and/or digital signals; and/or display-specific
data connections, such as HDMI, Component video, S-video, Composite
video; and/or media storage devices such as a USB flash drive, memory
card, or a DVD; and/or network connections, usually using internet
Protocol, typically carried over Ethernet or Wi-Fi. The requirements of
this part are limited to those televisions for which the Department of
Energy has adopted and published test procedures for measuring energy
use.
(i) Pool heater means an appliance designed for heating nonpotable
water contained at atmospheric pressure, including heating water in
swimming pools, spas, hot tubs and similar applications.
Sec. 305.11 [Removed]
0
4. Remove Sec. 305.11.
Sec. Sec. 305.4 through 305.8, 305.10, 305.12 through 305.17, and
305.19 through 305.25 [Redesignated as Sec. Sec. 305.7 through
305.11, 305.12, 305.20 through 305.25, and 305.26 through 305.32]
0
5. Redesignate the sections listed in the ``Old Section'' column as the
sections listed in the ``New Section'' column as shown in the following
table:
------------------------------------------------------------------------
Old Section New Section
------------------------------------------------------------------------
Sec. 305.4 Sec. 305.7
Sec. 305.5 Sec. 305.8
Sec. 305.6 Sec. 305.9
Sec. 305.7 Sec. 305.10
Sec. 305.8 Sec. 305.11
Sec. 305.10 Sec. 305.12
Sec. 305.12 Sec. 305.20
Sec. 305.13 Sec. 305.21
Sec. 305.14 Sec. 305.22
Sec. 305.15 Sec. 305.23
Sec. 305.16 Sec. 305.24
Sec. 305.17 Sec. 305.25
Sec. 305.19 Sec. 305.26
Sec. 305.20 Sec. 305.27
Sec. 305.21 Sec. 305.28
Sec. 305.22 Sec. 305.29
Sec. 305.23 Sec. 305.30
Sec. 305.24 Sec. 305.31
Sec. 305.25 Sec. 305.32
------------------------------------------------------------------------
0
6. Add new Sec. 305.4 to read as follows:
Sec. 305.4 Description of furnaces and central air conditioners.
(a) Furnaces--(1) Furnace means a product that utilizes only
single-phase electric current, or single-phase electric current or DC
current in conjunction with natural gas, propane, or home heating oil,
and which--
(i) Is designed to be the principal heating source for the living
space of a residence;
(ii) Is not contained within the same cabinet with a central air
conditioner
[[Page 58030]]
whose rated cooling capacity is above 65,000 Btu per hour;
(iii) Is an electric central furnace, electric boiler, forced-air
central furnace, gravity central furnace, or low pressure steam or hot
water boiler; and
(iv) Has a heat input rate of less than 300,000 Btu per hour for
electric boilers and low pressure steam or hot water boilers and less
than 225,000 Btu per hour for forced-air central furnaces, gravity
central furnaces, and electric central furnaces.
(2) Electric central furnace means a furnace designed to supply
heat through a system of ducts with air as the heating medium, in which
heat is generated by one or more electric resistance heating elements
and the heated air is circulated by means of a fan or blower.
(3) Forced air central furnace means a gas or oil burning furnace
designed to supply heat through a system of ducts with air as the
heating medium. The heat generated by combustion of gas or oil is
transferred to the air within a casing by conduction through heat
exchange surfaces and is circulated through the duct system by means of
a fan or blower.
(4) Gravity central furnace means a gas fueled furnace which
depends primarily on natural convection for circulation of heated air
and which is designed to be used in conjunction with a system of ducts.
(5) Electric boiler means an electrically powered furnace designed
to supply low pressure steam or hot water for space heating
application. A low pressure steam boiler operates at or below 15 pounds
per square inch gauge (psig) steam pressure; a hot water boiler
operates at or below 160 psig water pressure and 250 [deg]F water
temperature.
(6) Low pressure steam or hot water boiler means an electric, gas
or oil burning furnace designed to supply low pressure steam or hot
water for space heating application. A low pressure steam boiler
operates at or below 15 pounds psig steam pressure; a hot water boiler
operates at or below 160 psig water pressure and 250 [deg]F water
temperature.
(7) Outdoor furnace or boiler is a furnace or boiler normally
intended for installation out-of-doors or in an unheated space (such as
an attic or a crawl space).
(8) Weatherized warm air furnace or boiler means a furnace or
boiler designed for installation outdoors, approved for resistance to
wind, rain, and snow, and supplied with its own venting system.
(b) Central air conditioner means a product, other than a packaged
terminal air conditioner, which is powered by single phase electric
current, air cooled, rated below 65,000 Btu per hour, not contained
within the same cabinet as a furnace, the rated capacity of which is
above 225,000 Btu per hour, and is a heat pump or a cooling only unit.
(1) Condenser-evaporator coil combination means a condensing unit
made by one manufacturer and one of several evaporator coils, either
manufactured by the same manufacturer or another manufacturer, intended
to be combined with that particular condensing unit.
(2) Condensing unit means a component of a ``central air
conditioner'' which is designed to remove heat absorbed by the
refrigerant and to transfer it to the outside environment, and which
consists of an outdoor coil, compressor(s), and air moving device.
(3) Evaporator coil means a component of a central air conditioner
that is designed to absorb heat from an enclosed space and transfer the
heat to a refrigerant.
(4) Single package unit means any central air conditioner in which
all the major assemblies are enclosed in one cabinet.
(5) Split system means any central air conditioner in which one or
more of the major assemblies are separate from the others.
(c) Heat pump means a product, other than a packaged terminal heat
pump, which consists of one or more assemblies, powered by single phase
electric current, rated below 65,000 Btu per hour, utilizing an indoor
conditioning coil, compressor, and refrigerant-to-outdoor air heat
exchanger to provide air heating, and may also provide air cooling,
dehumidifying, humidifying, circulating, and air cleaning.
0
7. Add new Sec. 305.5 to read as follows:
Sec. 305.5 Description of lighting products.
(a) Fluorescent lamp ballast means a device which is used to start
and operate fluorescent lamps by providing a starting voltage and
current and limiting the current during normal operation.
(b) Fluorescent lamp means:
(1) A low pressure mercury electric-discharge source in which a
fluorescing coating transforms some of the ultra-violet energy
generated by the mercury discharge into light, including only the
following:
(i) Any straight-shaped lamp (commonly referred to as 4-foot medium
bi-pin lamps) with medium bi-pin bases of nominal overall length of 48
inches and rated wattage of 28 or more;
(ii) Any U-shaped lamp (commonly referred to as 2-foot U-shaped
lamps) with medium bi-pin bases of nominal overall length between 22
and 25 inches and rated wattage of 28 or more;
(iii) Any rapid start lamp as defined at 42 U.S.C.
6291(30)(A)(iii); and
(iv) Any instant start lamp as defined at 42 U.S.C.
6291(30)(A)(iv); but
(2) Fluorescent lamp does not mean any lamp excluded by the
Department of Energy, by rule, as a result of a determination that
standards for such lamp would not result in significant energy savings
because such lamp is designed for special applications or has special
characteristics not available in reasonably substitutable lamp types;
and
(3) General service fluorescent lamp means a fluorescent lamp which
can be used to satisfy the majority of fluorescent applications, but
does not mean any lamp designed and marketed for the following
nongeneral lighting applications:
(i) Fluorescent lamps designed to promote plant growth;
(ii) Fluorescent lamps specifically designed for cold temperature
installations;
(iii) Colored fluorescent lamps;
(iv) Impact-resistant fluorescent lamps;
(v) Reflectorized or aperture lamps;
(vi) Fluorescent lamps designed for use in reprographic equipment;
(vii) Lamps primarily designed to produce radiation in the ultra-
violet region of the spectrum; and
(viii) Lamps with a color rendering index of 82 or greater.
(c) General service lamp means:
(1) A lamp that is:
(i) A medium base compact fluorescent lamp;
(ii) A general service incandescent lamp;
(iii) A general service light-emitting diode (LED or OLED) lamp; or
(iv) Any other lamp that the Secretary of Energy determines is used
to satisfy lighting applications traditionally served by general
service incandescent lamps.
(2) Exclusions: The term general service lamp does not include--
(i) Any lighting application or bulb shape described in paragraphs
(e)(3)(ii)(A) through (T) of this section; and
(ii) Any general service fluorescent lamp.
(d) Medium base compact fluorescent lamp means an integrally
ballasted fluorescent lamp with a medium screw base, a rated input
voltage range of 115 to 130 volts and which is designed as a direct
replacement for a general service
[[Page 58031]]
incandescent lamp; however, the term does not include--
(1) Any lamp that is:
(i) Specifically designed to be used for special purpose
applications; and
(ii) Unlikely to be used in general purpose applications, such as
the applications described in the definition of ``General Service
Incandescent Lamp'' in paragraph (e)(3)(ii) of this section; or
(2) Any lamp not described in the definition of ``General Service
Incandescent Lamp'' in this section and that is excluded by the
Department of Energy, by rule, because the lamp is--
(i) Designed for special applications; and
(ii) Unlikely to be used in general purpose applications.
(e) Incandescent lamp means:
(1) A lamp in which light is produced by a filament heated to
incandescence by an electric current, including only the following:
(i) Any lamp (commonly referred to as lower wattage nonreflector
general service lamps, including any tungsten halogen lamp) that has a
rated wattage between 30 and 199 watts, has an E26 medium screw base,
has a rated voltage or voltage range that lies at least partially
within 115 and 130 volts, and is not a reflector lamp;
(ii) Any lamp (commonly referred to as a reflector lamp) which is
not colored or designed for rough or vibration service applications,
that contains an inner reflective coating on the outer bulb to direct
the light, an R, PAR, ER, BR, BPAR, or similar bulb shapes with E26
medium screw bases, a rated voltage or voltage range that lies at least
partially within 115 and 130 volts, a diameter which exceeds 2.25
inches, and has a rated wattage that is 40 watts or higher;
(iii) Any general service incandescent lamp (commonly referred to
as a high- or higher-wattage lamp) that has a rated wattage above 199
watts (above 205 watts for a high wattage reflector lamp); but
(2) Incandescent lamp does not mean any lamp excluded by the
Secretary of Energy, by rule, as a result of a determination that
standards for such lamp would not result in significant energy savings
because such lamp is designed for special applications or has special
characteristics not available in reasonably substitutable lamp types;
(3) General service incandescent lamp means:
(i) In general, a standard incandescent, halogen, or reflector type
lamp that--
(A) Is intended for general service applications;
(B) Has a medium screw base;
(C) Has a lumen range of not less than 310 lumens and not more than
2,600 lumens; and
(D) Is capable of being operated at a voltage range at least
partially within 110 and 130 volts.
(ii) Exclusions. The term ``general service incandescent lamp''
does not include the following incandescent lamps:
(A) An appliance lamp as defined at 42 U.S.C. 6291(30);
(B) A black light lamp;
(C) A bug lamp;
(D) A colored lamp as defined at 42 U.S.C. 6291(30);
(E) An infrared lamp;
(F) A left hand thread lamp;
(G) A marine lamp;
(H) A marine signal service lamp;
(I) A mine service lamp;
(J) A plant light lamp;
(K) A rough service lamp as defined at 42 U.S.C. 6291(30);
(L) A shatter resistant lamp (including a shatter-proof lamp and a
shatter-protected lamp);
(M) A sign service lamp;
(N) A silver bowl lamp;
(O) A showcase lamp;
(P) A traffic signal lamp;
(Q) A vibration service lamp as defined at 42 U.S.C. 6291(30);
(R) A G shape lamp as defined at 42 U.S.C. 6291(30)(D)(ii)(XX);
(S) A T shape lamp as defined at 42 U.S.C. 6291(30)(D)(ii)(XXI); or
(T) A B, BA, CA, F, G16-1/2, G-25, G-30, S, or M-14 lamp as defined
at 42 U.S.C. 6291(30)(D)(ii)(XXII).
(4) Incandescent reflector lamp means a lamp described in paragraph
(e)(1)(ii) of this section; and
(5) Tungsten halogen lamp means a gas filled tungsten filament
incandescent lamp containing a certain proportion of halogens in an
inert gas.
(f) Light emitting diode (LED) means a p-n junction solid state
device the radiated output of which is a function of the physical
construction, material used, and exciting current of the device. The
output of a light emitting diode may be in--
(1) The infrared region;
(2) The visible region; or
(3) The ultraviolet region.
(g) Organic light emitting diode (OLED) means a thin-film light-
emitting device that typically consists of a series of organic layers
between 2 electrical contacts (electrodes).
(h) General service light-emitting diode (LED or OLED) lamp means
any light emitting diode (LED or OLED) lamp that:
(1) Is a consumer product;
(2) Is intended for general service applications;
(3) Has a medium screw base;
(4) Has a lumen range of not less than 310 lumens and not more than
2,600 lumens; and
(5) Is capable of being operated at a voltage range at least
partially within 110 and 130 volts.
(i) Metal halide lamp fixture means a light fixture for general
lighting application that is designed to be operated with a metal
halide lamp and a ballast for a metal halide lamp and that is subject
to and complies with Department of Energy efficiency standards issued
pursuant to 42 U.S.C. 6295.
(1) Metal halide ballast means a ballast used to start and operate
metal halide lamps.
(2) Metal halide lamp means a high intensity discharge lamp in
which the major portion of the light is produced by radiation of metal
halides and their products of dissociation, possibly in combination
with metallic vapors.
(j) Specialty consumer lamp means:
(1) Any lamp that:
(i) Is not included under the definition of general service lamp in
this part;
(ii) Has a lumen range between 310 lumens and no more than 2,600
lumens or a rated wattage between 30 and 199;
(iii) Has one of the following bases:
(A) A medium screw base;
(B) A candelabra screw base;
(C) A GU-10 base; or
(D) A GU-24 base; and
(iv) Is capable of being operated at a voltage range at least
partially within 110 and 130 volts.
(2) Inclusions: The term specialty consumer lamp includes, but is
not limited to, the following lamps if such lamps meet the conditions
listed in paragraph (1):
(i) Vibration-service lamps as defined at 42 U.S.C. 6291(30)(AA);
(ii) Rough service lamps as defined at 42 U.S.C. 6291(30)(X);
(iii) Appliance lamps as defined at 42 U.S.C. 6291(30)(T); and
(iv) Shatter resistant lamps (including a shatter proof lamp and a
shatter protected lamp) as defined in 42 U.S.C. 6291(30)(Z).
(3) Exclusions: The term specialty consumer lamp does not include:
(i) A black light lamp;
(ii) A bug lamp;
(iii) A colored lamp;
(iv) An infrared lamp;
(v) A left-hand thread lamp;
(vi) A marine lamp;
(vii) A marine signal service lamp;
(viii) A mine service lamp;
(ix) A sign service lamp;
(x) A silver bowl lamp;
(xi) A showcase lamp;
[[Page 58032]]
(xii) A traffic signal lamp;
(xiii) A G-shape lamp with diameter of 5 inches or more;
(xiv) A C7, M-14, P, RP, S, or T shape lamp;
(xv) A intermediate screw-base lamp; and
(xvi) A plant light lamp.
0
8. Add new Sec. 305.6 to read as follows:
Sec. 305.6 Description of plumbing products.
(a) Showerhead means a component or set of components distributed
in commerce for attachment to a single supply fitting, for spraying
water onto a bather, typically from an overhead position, excluding
safety shower showerheads.
(b) Faucet means a lavatory faucet, kitchen faucet, metering
faucet, or replacement aerator for a lavatory or kitchen faucet.
(c) Water closet means a plumbing fixture having a water-containing
receptor which receives liquid and solid body waste and, upon
actuation, conveys the waste through an exposed integral trap seal into
a gravity drainage system, except such term does not include fixtures
designed for installation in prisons.
(d) Urinal means a plumbing fixture that receives only liquid body
waste and, on demand, conveys the waste through a trap seal into a
gravity drainage system, except such term does not include fixtures
designed for installation in prisons.
0
9. In newly re-designated Sec. 305.7:
0
a. Remove the reference ``Sec. 305.20'' and add in its place ``Sec.
305.27'' in paragraph (b)(5);
0
b. Remove the reference ``Sec. 305.26'' and add in its place ``Sec.
305.9'' in paragraph (b)(6);
0
c. Remove the reference ``Sec. 305.19'' and add in its place ``Sec.
305.26'' in paragraph (c);
0
d. Remove paragraph (d)(3); and
0
e. Revise paragraph (e).
The revision reads as follows:
Sec. 305.7 Prohibited acts.
* * * * *
(e) This part shall not apply to:
(1) Any covered product if it is manufactured, imported, sold, or
held for sale for export from the United States, so long as such
product is not in fact distributed in commerce for use in the United
States, and such covered product or the container thereof bears a stamp
or label stating that such covered product is intended for export.
(2) Televisions manufactured before May 10, 2011.
* * * * *
0
10. In newly redesignated Sec. 305.8, revise paragraph (c) to read as
follows:
Sec. 305.8 Determinations of estimated annual energy consumption,
estimated annual operating cost, and energy efficiency rating, water
use rate, and other required disclosure content.
* * * * *
(c) Representations for ceiling fans under Sec. 305.21 and
televisions under Sec. 305.25 must be derived from applicable
procedures in 10 CFR parts 429, 430, and 431.
0
11. Revise newly redesignated Sec. 305.9 to read as follows:
Sec. 305.9 Duty to provide labels on websites.
For each covered product required by this part to bear an
EnergyGuide or Lighting Facts label, the manufacturer must make a copy
of the label available on a publicly accessible website in a manner
that allows catalog sellers to hyperlink to the label or download it
for use in websites or paper catalogs. The label for each specific
model must remain on the website for six months after production of
that model ceases.
0
12. In newly redesignated Sec. 305.11, revise paragraph (a)(5), and in
paragraph (b)(1) introductory text, remove the reference to ``Sec.
305.8(a)'' and add in their place ``Sec. 305.11(a)''.
The revision reads as follows:
Sec. 305.11 Submission of data
(a) * * *
(5) Manufacturers must submit a website address for the online
EnergyGuide labels covered by Sec. 305.9 in new model and annual
reports required by this section. Manufacturers may accomplish this by
either submitting a specific link to a URL for each label, a link to a
PDF download for each label, or a link to a website that takes users
directly to a searchable database of the covered labels from which the
label image or download may be accessed using the model number as
certified to DOE pursuant to 10 CFR part 429 and the model number
advertised in product literature. Such label information must be
submitted either at the time the model is certified to DOE pursuant to
10 CFR part 429 or at some time on or before the annual report date
immediately following such certification. In lieu of submitting the
required information to the Commission, manufacturers may submit such
information to the Department of Energy via the CCMS at https://regulations.doe.gov/ccms as provided by 10 CFR 429.12. The requirements
in this paragraph do not apply to Lighting Facts labels.
* * * * *
0
13. In newly redesignated Sec. 305.12:
0
a. In paragraph (b):
0
i. Remove the reference ``Sec. 305.11'' and add in its place ``Sec.
305.14 through Sec. 305.19'';
0
ii. Remove the reference to ``Sec. 305.20'' and add in its place
``Sec. 305.27''; and
0
b. Revise paragraphs (c) introductory text and (c)(1);
The revisions read as follows:
Sec. 305.12 Ranges of comparability on the required labels.
* * * * *
(c) Operating costs or efficiency ratings outside current range.
When the estimated annual operating cost or energy efficiency rating of
a given model of a product covered by this section falls outside the
limits of the current range for that product, which could result from
the introduction of a new or changed model, the manufacturer shall:
(1) Omit placement of such product on the scale appearing on the
label, and
* * * * *
0
14. Add new Sec. 305.13 to read as follows:
Sec. 305.13 Layout, format, and placement of labels for
refrigerators, refrigerator-freezers, freezers, dishwashers, clothes
washers, water heaters, room air conditioners, and pool heaters.
(a) Coverage. The requirements of this section apply to labels for
refrigerators, refrigerator-freezers, freezers, dishwashers, clothes
washers, water heaters, room air conditioners, and pool heaters.
(b) Layout. Energy labels shall use one size, similar colors, and
typefaces with consistent positioning of headline, copy, and charts to
maintain uniformity for immediate consumer recognition and readability.
Trim size dimensions for the labels shall be as follows: Width must be
between 5\1/4\ inches and 5\1/2\ inches (13.34 cm. and 13.97 cm.);
length must be between 7\3/8\ inches (18.73 cm.) and 7\5/8\ (19.37
cm.). Copy is to be set between 27 picas and 29 picas and copy page
should be centered (right to left and top to bottom). Depth is variable
but should follow closely the prototype and sample labels appearing at
the end of this part illustrating the basic layout. All positioning,
spacing, type sizes, and line widths should be similar to and
consistent with the prototype and sample labels in appendix L to this
part.
(c) Type style and setting. The Arial series typeface or equivalent
shall be used exclusively on the label. Specific sizes and faces to be
used are indicated on the prototype labels. No hyphenation should be
used in setting headline or copy text. Positioning and spacing should
follow the prototypes closely. Generally, text must be set flush left
with two points leading except where
[[Page 58033]]
otherwise indicated. See the prototype labels for specific directions.
(d) Colors. Except as indicated in paragraph (e)(3) of this
section, the basic colors of all labels covered by this section shall
be process yellow or equivalent and process black. The label shall be
printed full bleed process yellow. All type and graphics shall be print
process black.
(e) Label types. Except as indicated in paragraph (e)(3) of this
section, the labels must be affixed to the product in the form of an
adhesive label for any product covered by this section, or in the form
of a hang tag for refrigerators, refrigerator-freezers, freezers,
dishwashers, and clothes washers, as follows:
(1) Adhesive labels. All adhesive labels should be applied so they
can be easily removed without the use of tools or liquids, other than
water, but should be applied with an adhesive with an adhesion capacity
sufficient to prevent their dislodgment during normal handling
throughout the chain of distribution to the retailer or consumer. The
paper stock for pressure-sensitive or other adhesive labels shall have
a basic weight of not less than 58 pounds per 500 sheets (25'' x 38'')
or equivalent, exclusive of the release liner and adhesive. A minimum
peel adhesion capacity for the adhesive of 12 ounces per square inch is
suggested, but not required if the adhesive can otherwise meet the
above standard. In lieu of a label with adhesive backing, manufacturers
may adhere the label with adhesive tape, provided the tape is affixed
along the entire top and bottom of the label.
(2) Hang tags. Labels may be affixed to the product interior in the
form of a hang tag using cable ties or double strings connected through
reinforced punch holes, or with attachment and label material of
equivalent or greater strength and durability. If paper stock is used
for hang tags, it shall have a basic weight of not less than 110 pounds
per 500 sheets (25\1/2\'' x 30\1/2\'' index). When materials are used
to attach the hang tags to appliance products, the materials shall be
of sufficient strength to insure that if gradual pressure is applied to
the hang tag by pulling it away from where it is affixed to the
product, the hang tag will tear before the material used to affix the
hang tag to the product breaks.
(3) Package labels for certain products. Labels for electric
instantaneous water heaters shall be printed on or affixed to the
product's packaging in a conspicuous location. Labels for room air
conditioners produced on or after October 1, 2019 shall be printed on
or affixed to the principal display panel of the product's packaging.
The labels for electric instantaneous water heaters and room air
conditioners shall be black type and graphics on a process yellow or
other neutral contrasting background.
(f) Placement--(1) Adhesive labels. Manufacturers shall affix
adhesive labels to the covered products in such a position that it is
easily read by a consumer examining the product. The label should be
generally located on the upper-right-front corner of the product's
front exterior. However, some other prominent location may be used as
long as the label will not become dislodged during normal handling
throughout the chain of distribution to the retailer or consumer. The
top of the label should not exceed 74 inches from the base of taller
products. The label can be displayed in the form of a flap tag adhered
to the top of the appliance and bent (folded at 90[deg]) to hang over
the front, as long as this can be done with assurance that it will be
readily visible.
(2) Hang tags. A hang tag shall be affixed to the interior of the
product in such a position that it can be easily read by a consumer
examining the product. A hang tag can be affixed in any position that
meets this requirement as long as the label will not become dislodged
during normal handling throughout the chain of distribution to the
retailer or consumer. Hang tags may only be affixed in refrigerators,
refrigerator-freezers, freezers, dishwashers, and clothes washers.
0
15. Add new Sec. 305.14 to read as follows:
Sec. 305.14 Label content for refrigerators, refrigerator-freezers,
and freezers.
(a) Label content. (1) Headlines and texts, as illustrated in the
prototype and sample labels in appendix L to this part, are standard
for all labels.
(2) Name of manufacturer or private labeler shall, in the case of a
corporation, be deemed to be satisfied only by the actual corporate
name, which may be preceded or followed by the name of the particular
division of the corporation. In the case of an individual, partnership,
or association, the name under which the business is conducted shall be
used. Inclusion of the name of the manufacturer or private labeler is
optional at the discretion of the manufacturer or private labeler.
(3) Model number(s) will be the designation given by the
manufacturer or private labeler.
(4) Capacity or size is that determined in accordance with this
part. The capacity provided on the label shall be the model's total
refrigerated volume (VT) as determined in accordance with this part and
the model description must be consistent with the categories described
in Appendices A and B to this part.
(5) Unless otherwise indicated in this paragraph, estimated annual
operating costs must be determined in accordance with this part. Labels
for dual-mode refrigerator-freezers that can operate as either a
refrigerator or a freezer must reflect the estimated energy cost of the
model's most energy intensive configuration.
(6) Unless otherwise indicated in this paragraph, ranges of
comparability for estimated annual operating costs are found in the
appropriate appendices accompanying this part.
(7) Placement of the labeled product on the scale shall be
proportionate to the lowest and highest estimated annual operating
costs.
(8) Labels must contain the model's estimated annual energy
consumption as determined in accordance with this part and as indicated
on the sample labels in appendix L.
(9) Labels must contain statements as illustrated in the prototype
labels in appendix L and specified as follows by product type:
(i) Labels for refrigerators, refrigerator-freezers, and freezers
shall contain the text and graphics illustrated in sample labels of
appendix L, including the statement:
Compare ONLY to other labels with yellow numbers.
Labels with yellow numbers are based on the same test procedures.
(ii) Labels for refrigerators and refrigerator-freezers must
contain a statement as illustrated in the prototype labels in appendix
L and specified as follows (fill in the blanks with the appropriate
energy cost figure):
Your cost will depend on your utility rates and use.
Both cost ranges based on models of similar size capacity.
[Insert statement required by paragraph (a)(9)(iii) of this
section].
Estimated energy cost based on a national average electricity cost
of __ cents per kWh.
ftc.gov/energy.
(iii) Labels for refrigerators and refrigerator-freezers shall
include the following as part of the statement required by paragraph
(a)(9)(ii) of this section:
(A) For models covered under appendix A1 to this part, the sentence
shall read:
Models with similar features have automatic defrost and no freezer.
(B) For models covered under appendix A2 to this part, the sentence
shall read:
[[Page 58034]]
Models with similar features have manual defrost.
(C) For models covered under appendix A3 to this part, the sentence
shall read:
Models with similar features have partial automatic defrost.
(D) For models covered under appendix A4 to this part, the sentence
shall read:
Models with similar features have automatic defrost, top-mounted
freezer, and no through-the-door ice.
(E) For models covered under appendix A5 to this part, the sentence
shall read:
Models with similar features have automatic defrost, side-mounted
freezer, and no through-the-door ice.
(F) For models covered under appendix A6 to this part, the sentence
shall read:
Models with similar features have automatic defrost, bottom-mounted
freezer, and no through-the-door ice.
(G) For models covered under appendix A7 to this part, the sentence
shall read:
Models with similar features have automatic defrost, bottom-mounted
freezer and through-the-door ice.
(H) For models covered under appendix A8 to this part, the sentence
shall read:
Models with similar features have automatic defrost, side-mounted
freezer, and through-the-door ice.
(iv) Labels for freezers must contain a statement as illustrated in
the prototype labels in appendix L and specified as follows (fill in
the blanks with the appropriate energy cost figure):
Your cost will depend on your utility rates and use.
[Insert statement required by paragraph (a)(10)(v) of this
section].
Estimated energy cost based on a national average electricity cost
of __cents per kWh.
ftc.gov/energy.
(v) For freezers, the following sentence shall be included as part
of the statement required by paragraph (a)(9)(iv) of this section:
(A) For models covered under appendix B1 to this part, the sentence
shall read:
Cost range based only on upright freezer models of similar capacity
with manual defrost.
(B) For models covered under appendix B2 to this part, the sentence
shall read:
Cost range based only on upright freezer models of similar capacity
with automatic defrost.
(C) For models covered under appendix B3 to this part, the sentence
shall read:
Cost range based only on chest and other freezer models of similar
capacity.
(10) The following statement shall appear on each label as
illustrated in the prototype and sample labels in appendix L to this
part:
Federal law prohibits removal of this label before consumer
purchase.
(b) Additional information. No marks or information other than that
specified in this part shall appear on or directly adjoining this label
except that:
(1) A part or publication number identification may be included on
this label, as desired by the manufacturer. If a manufacturer elects to
use a part or publication number, it must appear in the lower right-
hand corner of the label and be set in 12-point type or smaller.
(2) The energy use disclosure labels required by the governments of
Canada or Mexico may appear directly adjoining this label, as desired
by the manufacturer.
(3) The manufacturer or private labeler may include the ENERGY STAR
logo on the bottom right corner of the label for certified products.
The logo must be 1 inch by 1 inch in size. Only manufacturers that have
signed a Memorandum of Understanding with the Department of Energy or
the Environmental Protection Agency may add the ENERGY STAR logo to
labels on certified covered products; such manufacturers may add the
ENERGY STAR logo to labels only on those covered products that are
contemplated by the Memorandum of Understanding.
0
16. Add new Sec. 305.15 to read as follows:
Sec. 305.15 Label content for clothes washers.
(a) Label content. (1) Headlines and texts, as illustrated in the
prototype and sample labels in appendix L to this part, are standard
for all labels.
(2) Name of manufacturer or private labeler shall, in the case of a
corporation, be deemed to be satisfied only by the actual corporate
name, which may be preceded or followed by the name of the particular
division of the corporation. In the case of an individual, partnership,
or association, the name under which the business is conducted shall be
used. Inclusion of the name of the manufacturer or private labeler is
optional at the discretion of the manufacturer or private labeler.
(3) Model number(s) will be the designation given by the
manufacturer or private labeler.
(4) Capacity or size is that determined in accordance with this
part.
(5) Estimated annual operating costs are as determined in
accordance with this part. Labels must disclose estimated annual
operating cost for both electricity and natural gas as illustrated in
the sample labels in appendix L to this part.
(6) Unless otherwise indicated in this paragraph, ranges of
comparability for estimated annual operating costs are found in the
appropriate appendices accompanying this part.
(7) Placement of the labeled product on the scale shall be
proportionate to the lowest and highest estimated annual operating
costs.
(8) Labels must contain the model's estimated annual energy
consumption as determined in accordance with this part and as indicated
on the sample labels in appendix L.
(9) The label shall contain the text and graphics illustrated in
the sample labels in appendix L, including the statement:
Compare ONLY to other labels with yellow numbers.
Labels with yellow numbers are based on the same test procedures.
(10) Labels must contain a statement as illustrated in the
prototype labels in appendix L and specified as follows (fill in the
blanks with the appropriate capacity and energy cost figures):
Your costs will depend on your utility rates and use.
Cost range based only on [compact/standard] capacity models.
Estimated energy cost is based on six wash loads a week and a
national average electricity cost of __ cents per kWh and natural gas
cost of $ __ per therm.
ftc.gov/energy.
(11) The following statement shall appear on each label as
illustrated in the prototype and sample labels in appendix L:
Federal law prohibits removal of this label before consumer
purchase.
(b) Additional information. No marks or information other than that
specified in this part shall appear on or directly adjoining this label
except that:
(1) A part or publication number identification may be included on
this label, as desired by the manufacturer. If a manufacturer elects to
use a part or publication number, it must appear in the lower right-
hand corner of the label and be set in 12-point type or smaller.
(2) The energy use disclosure labels required by the governments of
Canada or Mexico may appear directly adjoining this label, as desired
by the manufacturer.
(3) The manufacturer or private labeler may include the ENERGY STAR
logo on the bottom right corner of the label for certified products.
The logo must be 1 inch by 1 inch in size. Only manufacturers that have
signed a Memorandum of Understanding with
[[Page 58035]]
the Department of Energy or the Environmental Protection Agency may add
the ENERGY STAR logo to labels on certified covered products; such
manufacturers may add the ENERGY STAR logo to labels only on those
covered products that are contemplated by the Memorandum of
Understanding.
0
17. Add new Sec. 305.16 to read as follows.
Sec. 305.16 Label content for dishwashers.
(a) Label content. (1) Headlines and texts, as illustrated in the
prototype and sample labels in appendix L to this part, are standard
for all labels.
(2) Name of manufacturer or private labeler shall, in the case of a
corporation, be deemed to be satisfied only by the actual corporate
name, which may be preceded or followed by the name of the particular
division of the corporation. In the case of an individual, partnership,
or association, the name under which the business is conducted shall be
used. Inclusion of the name of the manufacturer or private labeler is
optional at the discretion of the manufacturer or private labeler.
(3) Model number(s) will be the designation given by the
manufacturer or private labeler.
(4) Capacity or size is that determined in accordance with this
part.
(5) Estimated annual operating costs are as determined in
accordance with this part. Labels must disclose estimated annual
operating cost for both electricity and natural gas as illustrated in
the sample labels in appendix L to this part.
(6) Unless otherwise indicated in this paragraph, ranges of
comparability for estimated annual operating costs are found in the
appropriate appendices accompanying this part.
(7) Placement of the labeled product on the scale shall be
proportionate to the lowest and highest estimated annual operating
costs.
(8) Labels must contain the model's estimated annual energy
consumption as determined in accordance with this part and as indicated
on the sample labels in appendix L.
(9) Labels must contain a statement as illustrated in the prototype
labels in appendix L and specified as follows (fill in the brackets
with the appropriate capacity and the energy cost figures):
Your costs will depend on your utility rates and use.
Cost range based only on [compact/standard] capacity models.
Estimated energy cost is based on four wash loads a week, and a
national average electricity cost of [__] cents per kWh and natural gas
cost of $[__] per therm.
For more information, visit www.ftc.gov/energy.
(10) The following statement shall appear on each label as
illustrated in the prototype and sample labels in appendix L to this
part:
Federal law prohibits removal of this label before consumer
purchase.
(b) Additional information. No marks or information other than that
specified in this part shall appear on or directly adjoining this label
except that:
(1) A part or publication number identification may be included on
this label, as desired by the manufacturer. If a manufacturer elects to
use a part or publication number, it must appear in the lower right-
hand corner of the label and be set in 12-point type or smaller.
(2) The energy use disclosure labels required by the governments of
Canada or Mexico may appear directly adjoining this label, as desired
by the manufacturer.
(3) The manufacturer or private labeler may include the ENERGY STAR
logo on the bottom right corner of the label for certified products.
The logo must be 1 inch by 1 inch in size. Only manufacturers that have
signed a Memorandum of Understanding with the Department of Energy or
the Environmental Protection Agency may add the ENERGY STAR logo to
labels on certified covered products; such manufacturers may add the
ENERGY STAR logo to labels only on those covered products that are
contemplated by the Memorandum of Understanding.
0
18. Add new Sec. 305.17 to read as follows:
Sec. 305.17 Label content for water heaters.
(a) Label content. (1) Headlines and texts, as illustrated in the
prototype and sample labels in appendix L to this part, are standard
for all labels.
(2) Name of manufacturer or private labeler shall, in the case of a
corporation, be deemed to be satisfied only by the actual corporate
name, which may be preceded or followed by the name of the particular
division of the corporation. In the case of an individual, partnership,
or association, the name under which the business is conducted shall be
used. Inclusion of the name of the manufacturer or private labeler is
optional at the discretion of the manufacturer or private labeler.
(3) Model number(s) will be the designation given by the
manufacturer or private labeler.
(4) Capacity or size is that determined in accordance with this
part. Capacity for storage water heaters shall be presented in both
rated storage volume (``tank size (storage capacity)'') and first hour
rating as indicated on the sample label in appendix L to this part.
(5) Estimated annual operating costs are as determined in
accordance with this part.
(6) Unless otherwise indicated in this paragraph, ranges of
comparability for estimated annual operating costs are found in the
appropriate appendices accompanying this part.
(7) Placement of the labeled product on the scale shall be
proportionate to the lowest and highest estimated annual operating
costs.
(8) Labels must contain the model's estimated annual energy
consumption as determined in accordance with this part and as indicated
on the sample labels in appendix L to this part.
(9) Labels must contain a statement as illustrated in the prototype
labels in appendix L to this part and specified as follows by product
type:
(i) For water heaters covered by appendices D1, D2, and D3 to this
part, the statement will read as follows (fill in the blanks with the
appropriate fuel type, and energy cost figures):
Your costs will depend on your utility rates and use.
Cost range based only on models fueled by [natural gas, oil,
propane, or electricity] with a [very small, low, medium, or high]
first hour rating [fewer than 18 gallons, 18-50.9 gallons, 51-74.9
gallons, or greater than 75 gallons].
Estimated energy cost is based on a national average [electricity,
natural gas, propane, or oil] cost of [__ cents per kWh or $__ per
therm or gallon].
Estimated yearly energy use: __ [kWh or therms].
ftc.gov/energy.
(ii) For instantaneous water heaters, the statement will read as
follows (fill in the blanks with the appropriate model type, and the
energy cost figures):
Your costs will depend on your utility rates and use.
Cost range based only on [electric models or models fueled by
natural gas] with a [very small, low, medium, or high] gallons per
minute rating [0 to 1.6, 1.7 to 2.7, 2.8 to 4.0, or greater than 4.0].
Estimated energy cost is based on a national average [electricity,
natural gas, or propane] cost of [__ cents per kWh or $__ per therm or
gallon].
Estimated yearly energy use: __ [kWh or therms].
ftc.gov/energy.
(10) The following statement shall appear on each label as
illustrated in the prototype and sample labels in appendix L:
Federal law prohibits removal of this label before consumer
purchase.
(b) Additional information. No marks or information other than that
specified
[[Page 58036]]
in this part shall appear on or directly adjoining this label except
that:
(1) A part or publication number identification may be included on
this label, as desired by the manufacturer. If a manufacturer elects to
use a part or publication number, it must appear in the lower right-
hand corner of the label and be set in 12-point type or smaller.
(2) The energy use disclosure labels required by the governments of
Canada or Mexico may appear directly adjoining this label, as desired
by the manufacturer.
(3) The manufacturer or private labeler may include the ENERGY STAR
logo on the bottom right corner of the label for certified products.
The logo must be 1 inch by 1 inch in size. Only manufacturers that have
signed a Memorandum of Understanding with the Department of Energy or
the Environmental Protection Agency may add the ENERGY STAR logo to
labels on certified covered products; such manufacturers may add the
ENERGY STAR logo to labels only on those covered products that are
contemplated by the Memorandum of Understanding.
0
19. Add Sec. 305.18 to read as follows:
Sec. 305.18 Label content for room air conditioners.
(a) Label content. (1) Headlines and texts, as illustrated in the
prototype and sample labels in appendix L to this part, are standard
for all labels.
(2) Name of manufacturer or private labeler shall, in the case of a
corporation, be deemed to be satisfied only by the actual corporate
name, which may be preceded or followed by the name of the particular
division of the corporation. In the case of an individual, partnership,
or association, the name under which the business is conducted shall be
used. Inclusion of the name of the manufacturer or private labeler is
optional at the discretion of the manufacturer or private labeler.
(3) Model number(s) will be the designation given by the
manufacturer or private labeler.
(4) Capacity or size is that determined in accordance with this
part.
(5) Estimated annual operating costs are as determined in
accordance with this part.
(6) Unless otherwise indicated in this paragraph, ranges of
comparability for estimated annual operating costs are found in the
appropriate appendices accompanying this part.
(7) Placement of the labeled product on the scale shall be
proportionate to the lowest and highest estimated annual operating
costs.
(8) Labels must contain the model's estimated annual energy
consumption as determined in accordance with this part and as indicated
on the sample labels in appendix L. Labels must contain the model's
energy efficiency rating, as applicable, as determined in accordance
with this part and as indicated on the sample labels in appendix L to
this part.
(9) Labels must contain a statement as illustrated in the prototype
labels in appendix L and specified as follows (fill in the blanks with
the appropriate model type, year, energy type, and energy cost figure):
Your costs will depend on your utility rates and use.
Cost range based only on models [of similar capacity without
reverse cycle and with louvered sides; of similar capacity without
reverse cycle and without louvered sides; with reverse cycle and with
louvered sides; or with reverse cycle and without louvered sides].
Estimated annual energy cost is based on a national average
electricity cost of __ cents per kWh and a seasonal use of 8 hours use
per day over a 3 month period.
For more information, visit www.ftc.gov/energy.
(10) The following statement shall appear on each label as
illustrated in the prototype and sample labels in appendix L:
Federal law prohibits removal of this label before consumer
purchase.
(b) Additional information. No marks or information other than that
specified in this part shall appear on or directly adjoining this label
except that:
(1) A part or publication number identification may be included on
this label, as desired by the manufacturer. If a manufacturer elects to
use a part or publication number, it must appear in the lower right-
hand corner of the label and be set in 12-point type or smaller.
(2) The energy use disclosure labels required by the governments of
Canada or Mexico may appear directly adjoining this label, as desired
by the manufacturer.
(3) The manufacturer or private labeler may include the ENERGY STAR
logo on the bottom right corner of the label for certified products.
The logo must be 1 inch by 1 inch in size. Only manufacturers that have
signed a Memorandum of Understanding with the Department of Energy or
the Environmental Protection Agency may add the ENERGY STAR logo to
labels on certified covered products; such manufacturers may add the
ENERGY STAR logo to labels only on those covered products that are
contemplated by the Memorandum of Understanding.
0
20. Add new Sec. 305.19 to read as follows:
Sec. 305.19 Label content for pool heaters.
(a) Label content. (1) Headlines and texts, as illustrated in the
prototype and sample labels in appendix L to this part, are standard
for all labels.
(2) Name of manufacturer or private labeler shall, in the case of a
corporation, be deemed to be satisfied only by the actual corporate
name, which may be preceded or followed by the name of the particular
division of the corporation. In the case of an individual, partnership,
or association, the name under which the business is conducted shall be
used. Inclusion of the name of the manufacturer or private labeler is
optional at the discretion of the manufacturer or private labeler.
(3) Model number(s) will be the designation given by the
manufacturer or private labeler.
(4) Capacity or size is that determined in accordance with this
part.
(5) Thermal efficiencies are as determined in accordance with this
part.
(6) Unless otherwise indicated in this paragraph, ranges of
comparability for thermal efficiencies are found in the appropriate
appendices accompanying this part.
(7) Placement of the labeled product on the scale shall be
proportionate to the lowest and highest thermal efficiencies.
(8) Labels must contain the model's energy efficiency rating or
thermal efficiency, as applicable, as determined in accordance with
this part and as indicated on the sample labels in appendix L to this
part.
(9) Labels must contain a statement as illustrated in the prototype
labels in appendix L and specified as follows:
Efficiency range based only on models fueled by [natural gas or
oil].
For more information, visit www.ftc.gov/energy.
(10) The following statement shall appear on each label as
illustrated in the prototype and sample labels in appendix L to this
part:
Federal law prohibits removal of this label before consumer
purchase.
(b) Additional information. No marks or information other than that
specified in this part shall appear on or directly adjoining this label
except that:
(1) A part or publication number identification may be included on
this label, as desired by the manufacturer. If a manufacturer elects to
use a part or publication number, it must appear in the lower right-
hand corner of the label and be set in 12-point type or smaller.
(2) The energy use disclosure labels required by the governments of
Canada
[[Page 58037]]
or Mexico may appear directly adjoining this label, as desired by the
manufacturer.
(3) The manufacturer or private labeler may include the ENERGY STAR
logo on the bottom right corner of the label for certified products.
The logo must be 1 inch by 1 inch in size. Only manufacturers that have
signed a Memorandum of Understanding with the Department of Energy or
the Environmental Protection Agency may add the ENERGY STAR logo to
labels on certified covered products; such manufacturers may add the
ENERGY STAR logo to labels only on those covered products that are
contemplated by the Memorandum of Understanding.
Sec. 305.20 [Amended]
0
21. In newly redesignated Sec. 305.20:
0
a. Remove the reference ``Sec. 305.5'' and add in its place ``this
part'' in paragraph (f)(5);
0
b. Remove ``6-point'' and add in its place ``12-point'' in paragraph
(f)(10)(i);
0
c. Remove the reference ``Sec. 305.5'' and add in its place ``this
part'' in two occurrences in paragraph (g)(5);
0
d. Remove ``7A'' and add in its place ``7'' in paragraph (g)(6)(i); and
0
e. Remove ``6-point'' and add in its place ``12-point'' in paragraph
(g)(15)(i).
Sec. 305.21 [Amended]
0
22. In newly redesignated Sec. 305.21, remove the references to
``Sec. 305.5'' and add in their place the reference ``Sec. 305.8'' in
paragraphs (a)(1)(iii) and (iv).
Sec. 305.23 [Amended]
0
23. In newly redesignated Sec. 305.23:
0
a. Remove the reference ``Sec. 305.2(n)'' and add in its place ``this
part'' in paragraph (a)(1);
0
b. Remove the reference ``Sec. 305.2(w)'' and add in its place ``this
part'' in paragraph (b)(3)(iii);
0
c. Remove the reference ``Sec. 305.2(hh)'' and add in its place ``this
part'' in paragraph (b)(3)(v); and
0
d. Remove the reference ``Sec. 305.2(w)'' and add in its place ``this
part'' in paragraph (c)(2)(i)(C).
Sec. 305.24 [Amended]
0
24. Amend newly redesignated Sec. 305.24 by removing paragraphs (b)(4)
and (5).
Sec. 305.25 [Amended]
0
25. In newly redesignated Sec. 305.25, in the locations cited in the
``Paragraph'' column, remove the reference indicated in the ``Remove''
column, and add in its place the reference indicated in the ``Add''
column.
------------------------------------------------------------------------
Paragraph Remove Add
------------------------------------------------------------------------
(d)(3)...................... Sec. 305.11(d)(2). Sec. 305.13(e)(2).
(f)(4)...................... Sec. 305.5 of this this part.
part.
(f)(7)...................... Sec. 305.5........ this part.
(g)......................... Sec. 305.6........ Sec. 305.9.
------------------------------------------------------------------------
Sec. 305.26 [Amended]
0
26. In newly redesignated Sec. 305.26:
0
a. Remove the reference ``305.11(f)'' and add in its place ``this
part'' in paragraph (a)(4); and
0
b. Remove the reference ``305.4(e)'' and add in its place ``Sec.
305.7(e)'' in paragraph (b)(4);
Sec. 305.27 [Amended]
0
27. In newly redesignated Sec. 305.27, in the locations cited in the
``Paragraph'' column, remove the reference indicated in the ``Remove''
column, and add in its place the reference indicated in the ``Add''
column.
------------------------------------------------------------------------
Paragraph Remove Add
------------------------------------------------------------------------
(b)(1)(i)(F) and (G)........ Sec. 305.5........ this part.
(b)(1)(i)(A) and (B)........ Sec. 305.5 and this part.
appendix K of this
Part.
(b)(1)(i)(C)................ Sec. 305.5 and this part.
appendix K.
(b)(1)(i)(A)-(C) and (G).... Sec. 305.7........ this part
(b)(1)(i)(E)................ Sec. 305.13....... Sec. 305.21.
(b)(1)(i)(D)................ Sec. 305.15....... Sec. 305.23.
(b)(1)(i)(D)................ Sec. Sec.
305.15(b)(3)(iv). 305.23(b)(3)(iv).
(b)(1)(i)(D)................ Sec. 305.15(d)(1). Sec. 305.23(g)(1).
(a)(1)(ii)(A)............... Sec. 305.16....... this part.
(b)(1)(ii).................. Sec. Sec.
305.20(a)(1)(ii). 305.27(a)(1)(ii).
(b)(2)...................... Sec. Sec.
305.20(b)(1)(i) and 305.27(b)(1)(i) and
(ii). (ii).
------------------------------------------------------------------------
Sec. 305.29 [Amended]
0
28. In newly redesignated Sec. 305.29, remove the reference to ``Sec.
305.21(b)'' and add in its place the reference ``Sec. 305.28(b)''.
0
29. Revise the heading for appendix A4 to part 305 to read as follows:
Appendix A4 to Part 305--Refrigerator-Freezers With Automatic Defrost
With Top-Mounted Freezer No Through-the-Door Ice
* * * * *
0
30. Revise the heading for appendix A5 to part 305 to read as follows:
Appendix A5 to Part 305--Refrigerator-Freezers With Automated Defrost
With Side-Mounted Freezer No Through-the-Door Ice
* * * * *
0
31. Revise the heading for appendix A6 to part 305 to read as follows:
Appendix A6 to Part 305--Refrigerator-Freezers With Automated Defrost
With Bottom-Mounted Freezer No Through-the-Door Ice
* * * * *
* * * * *
Appendix K1 to Part 305 [Amended]
0
32. In appendix K1, remove ``Sec. Sec. 305.11 and 305.20'' and add in
its place ``Sec. Sec. 305.14, 305.15, 305.17, and 305.27''.
[[Page 58038]]
Appendix K2 to Part 305 [Amended]
0
33. In appendix K2, remove ``Sec. Sec. 305.11 and 305.20'' and add in
its place ``Sec. Sec. 305.16, 305.18 and 305.27''.
0
34. In appendix L, revise Prototype Labels 1, 2, 6, and 7 and Sample
Labels 1, 2, 3, 13C, and 13D to read as follows:
BILLING CODE 6750-01-P
Appendix L to Part 305--Sample Labels
[GRAPHIC] [TIFF OMITTED] TR30OC19.003
* * * * *
[[Page 58039]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.004
[[Page 58040]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.005
* * * * *
[[Page 58041]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.006
[[Page 58042]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.007
[[Page 58043]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.008
* * * * *
[[Page 58044]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.009
[[Page 58045]]
[GRAPHIC] [TIFF OMITTED] TR30OC19.010
* * * * *
By direction of the Commission.
April J. Tabor,
Acting Secretary.
[FR Doc. 2019-23505 Filed 10-29-19; 8:45 am]
BILLING CODE 6750-01-C
