Exemption petitions, etc.: Thrall Car Manufacturing Co.,

[Federal Register: August 11, 2000 (Volume 65, Number 156)]

[Notices]

[Page 49288-49289]

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

[DOCID:fr11au00-129]

DEPARTMENT OF TRANSPORTATION

Federal Railroad Administration

Petition for Waiver of Compliance

In accordance with Part 211 of Title 49 Code of Federal Regulations (CFR), notice is hereby given that the Federal Railroad Administration (FRA) received a request for a waiver of compliance with certain requirements of its safety standards. The individual petition is described below, including the party seeking relief, the regulatory provisions involved, the nature of the relief being requested, and the petitioner's arguments in favor of relief.

Thrall Car Manufacturing Company

[Waiver Petition Docket Number FRA-1999-6358]

Thrall Car Manufacturing Company (TCMC) seeks a permanent waiver of compliance with certain provisions of the Railroad Safety Appliance Standards, 49 CFR Part 231.24, as they apply to auto carrying railcars as follows:

1. Use the reduced wording described in Parts 231.24 (j)(1) and 231.24 (j)(2) rather than 231.27 (j)(1) and (j)(2). Part 231.24 (j)(1) states ``That portion of each end of car more than fifteen (15) feet above top of rail shall be painted with contrasting reflectorized paint and shall bear the words ``No running board'' to the left of center and ``Excess height car'' to the right of center.'' Section 231.24 (j)(2) states ``On each side-sill near end corner there shall be painted a yellow rectangular area with a three-fourths (\3/4\) inch black border containing the words ``This car excess height--no running board.'' Lettering to be not less than one and one-half (1\1/2\) inches high.''

   TCMC requests to use the wording in 231.24, regarding running boards, due to the cars not being so equipped.

2. TCMC requests that the word ``material'' be substituted for ``paint'' in this section to permit utilizing new technological advancements in reflectorization.

3. Section 231.24 (j)(2) requires that ``On each side-sill near end corner there shall be painted a yellow rectangular area with a three- fourths (\3/4\) inch black border containing the words `This car excess height . . .' '' TCMC petitions to relocate this stencil/decal from the side-sill, if room is not available, to the shear panel of the auto rack. The stencil/decal will be located as low as possible on three corners of the car and directly above the handbrake on the ``BL'' corner.

4. TCMC requests that ``contrasting color'' borders be allowed on cars with dark exterior paint whereas a black border, required in 231.24 (j)(2) and 231.27 (j)(2), would not be readily visible.

5. TCMC requests that the maximum allowable misalignment between the front inside edge of the auto rack ladder stile to the inside edge of the flat car sill step be increased from the dimensions

   [[Page 49289]]

   listed in Motive Power and Equipment Technical Bulletin 98-05 to six (6) inches. This relief would be consistent with guidelines set forth in AAR's Manual of Standards and Recommended Practices, S-2038-85, 2.3.4.

   Interested parties are invited to participate in these proceedings by submitting written views, data, or comments. FRA does not anticipate scheduling a public hearing in connection with these proceedings since the facts do not appear to warrant a hearing. If any interested party desires an opportunity for oral comment, they should notify FRA, in writing, before the end of the comment period and specify the basis for their request.

   All communications concerning these proceedings should identify the appropriate docket number (e.g., Waiver Petition Docket Number 1999- 6358) and must be submitted to the Docket Clerk, DOT Docket Management Facility, Room PL-401 (Plaza Level), 400 7th Street, S.W., Washington, D.C. 20590. Communications received within 45 days of the date of this notice will be considered by FRA before final action is taken. Comments received after that date will be considered as far as practicable. All written communications concerning these proceedings are available for examination during regular business hours (9:00a.m.--5:00p.m.) at the above facility. All documents in the public docket are also available for inspection and copying on the Internet at the docket facility's web site at http://dms.dot.gov.

   Issued in Washington, D.C. on August 7, 2000. Grady C. Cothen, Jr., Deputy Associate Administrator for Safety Standards and Program Development.

   [FR Doc. 00-20452Filed8-10-00; 8:45 am]

   BILLING CODE 4910-06-U