Hazardous Materials:

Federal Register: December 23, 2010 (Volume 75, Number 246)

Proposed Rules

Page 80765-80773

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

DOCID:fr23de10-27

DEPARTMENT OF TRANSPORTATION

Pipeline and Hazardous Materials Safety Administration 49 CFR Parts 171, 173, 178, and 180

Docket Number PHMSA-2010-0019 (HM-241)

RIN 2137-AE58

Hazardous Materials: Adoption of ASME Code Section XII and the

National Board Inspection Code

AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA),

DOT.

ACTION: Advance notice of proposed rulemaking (ANPRM).

SUMMARY: PHMSA is considering amending the Hazardous Materials

Regulations (HMR) to incorporate the most recent edition of the

American Society of Mechanical Engineers' Boiler and Pressure Vessel

Code, Section XII for the design, construction, and certification of cargo tank motor vehicles, cryogenic portable tanks and multi-unit-tank car tanks (ton tanks). PHMSA is also considering incorporating by reference the National Board of Boiler and Pressure Vessel Inspectors'

National Board Inspection Code as it applies to the continuing qualification and maintenance of ASME stamped cargo tank motor vehicles, portable tanks, and multi-unit-tank car tanks (ton tanks) constructed to standards in ASME Section VIII or ASME Section XII. In this ANPRM, PHMSA is soliciting comments on the advisability of incorporating the most recent editions of these two standards by reference. We request comments to identify any gaps or inconsistencies between current HMR requirements and these consensus standards.

Additionally, we seek input regarding any potential costs, benefits, and burdens associated with compliance with these consensus standards.

DATES: Submit comments by March 23, 2011. To the extent possible, PHMSA will consider late-filed comments as we determine whether additional rulemaking is necessary.

ADDRESSES: You may submit comments identified by the docket number

(PHMSA-2010-0019; HM-241) by any of the following methods:

Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the online instructions for submitting comments.

Fax: 1-202-493-2251.

Mail: Docket Operations, U.S. Department of

Transportation, West

Page 80766

Building, Ground Floor, Room W12-140, Routing Symbol M-30, 1200 New

Jersey Avenue, SE., Washington, DC 20590.

Hand Delivery: To Docket Operations, Room W12-140 on the ground floor of the West Building, 1200 New Jersey Avenue, SE.,

Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal Holidays.

Instructions: All submissions must include the agency name and docket number for this notice at the beginning of the comment. Note that all comments received will be posted without change to the docket management system, including any personal information provided.

Docket: For access to the dockets to read background documents or comments received, go to http://www.regulations.gov, or DOT's Docket

Operations Office (see ADDRESSES).

Privacy Act: Anyone is able to search the electronic form of any written communications and comments received into any of our dockets by the name of the individual submitting the document (or signing the document, if submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477) or you may visit http://www.regulations.gov.

FOR FURTHER INFORMATION CONTACT: Kurt Eichenlaub or Ben Supko,

Standards and Rulemaking Division, (202) 366-8553, or Charles Hochman,

Engineering and Research Division, (202) 366-4492, Pipeline and

Hazardous Materials Safety Administration, 1200 New Jersey Avenue, SE.,

Washington, DC 20590.

SUPPLEMENTARY INFORMATION:

I. Abbreviations and Terms Used in This Document

AI: Authorized Inspector

ANSI: American National Standards Institute

ASME: American Society of Mechanical Engineers

BPVC: Boiler and Pressure Vessel Code

CI: Certified Individual

CTMV: Cargo Tank Motor Vehicle

DCE: Design Certifying Engineer

FMCSA: Federal Motor Carrier Safety Administration

HMR: Hazardous Materials Regulations (49 CFR Parts 171-180)

MAWP: Maximum Allowable Working Pressure

NBIC: National Board Inspection Code

PHMSA: Pipeline and Hazardous Materials Safety Administration

PVMA: Pressure Vessel Manufacturers Association

QI: Qualified Inspector

RI: Registered Inspector

Section XII: ASME BPVC, Section XII

II. Background

The Federal hazardous materials transportation law (49 U.S.C. 5101 et seq. (Federal hazmat law)) authorizes the Secretary of

Transportation to regulate the safe and secure transportation of hazardous materials in commerce. In accordance with its delegated authority from the Secretary, PHMSA has established hazardous materials safety regulations applicable to packagings used to transport hazardous materials in commerce, including requirements for the design, construction, qualification, maintenance, and repair of bulk packagings such as cargo tanks, portable tanks, and ton tanks.

Under 49 CFR 1.53, PHMSA is delegated the responsibility to enforce the Hazardous Materials Regulations. In addition, under 49 CFR 1.49(s) and 1.73(d), the Federal Railroad Administration and the Federal Motor

Carrier Safety Administration (FMCSA) are delegated authority to enforce the Hazardous Materials Regulations (HMR; 49 CFR parts 171-180) with particular emphasis on railroad and highway transportation respectively. PHMSA, FRA and FMCSA work closely with the regulated industry through educational assistance activities and FRA's and

FMCSA's compliance and enforcement programs.

General requirements for cargo tank motor vehicles (CTMVs), portable tanks, and ton tanks such as outage and filling limits, are prescribed in Sec. 173.24b. Detailed design and construction requirements that encompass material of construction, structural integrity, closures, openings, inlets and outlets, pressure relief devices, valves and fittings, tests, certification, etc., are specified in 49 CFR part 178, subpart H for portable tanks, subpart J for CTMVs and 49 CFR part 179, subpart E for multi-unit tank car tanks (ton tanks). Requirements applicable to continuing qualification and maintenance encompassing periodic tests and inspections, repairs, modifications, alterations, and conversions are specified in 49 CFR part 180, subpart E for CTMVs, subpart F for ton tanks, and subpart G for portable tanks. Design, construction and qualification of rail tank cars (49 CFR part 179 and part 180, subpart F) and non-specification cargo tanks (i.e., nurse tanks) are not being considered in the ANPRM.

Currently, the HMR incorporate by reference the ASME BPVC, Section

VIII, Division I, as part of the standards for the design and construction of cryogenic portable tanks and CTMVs. Section VIII sets forth detailed criteria for the design, construction, certification, and marking of stationary boilers and pressure vessels. Many factors exerted on stationary tanks such as pressure, temperature changes, and atmospheric conditions are the same as those encountered by transportation tanks. However, Section VIII does not address unique conditions and stresses encountered by tanks in the transportation environment. To address differences between stationary tanks and transportation tanks, the HMR contain additional design and construction requirements to account for conditions and stresses likely to occur in transportation.

III. Petitions for Rulemaking

In this ANPRM, PHMSA is considering three petitions for rulemaking from ASME, the National Board, and the Pressure Vessel Manufacturers

Association (PVMA). 1. On May 10, 2005, ASME petitioned PHMSA to revise the HMR to incorporate by reference the ASME Boiler and Pressure Vessel Code,

Section XII, Transport Tanks--2004 edition. Section XII of the BPVC contains requirements for construction and continued service of ASME pressure vessels for the transportation of dangerous goods with design pressures appropriate for the transportation mode and volumes greater than 450 liters (120 gallons) via highway, railway, air, or water. The construction requirements cover materials, design, fabrication, examination, inspection, testing, certification, and over-pressure protection. The requirements for continued service cover inspection, testing, repair, alteration, and recertification of in-service ASME stamped transport tanks. These transport tank requirements include the pressure vessel, appurtenances, and additional components that are covered by Modal Appendices for the specific transport modes and unique service conditions of the specific application. The 2004 edition contains one Modal Appendix for portable tanks carrying cryogenic liquids. The 2007 edition was expanded to include the Modal Appendix for cargo tanks. The 2010 edition was expanded to include the Modal

Appendix for ton tanks. [P-1459; Docket No. PHMSA-2005-21351]. 2. On February 27, 2006, PVMA petitioned PHMSA to revise the HMR to incorporate by reference the ASME Boiler and Pressure Vessel Code,

Section XII Transport Tanks--2004 edition. PVMA and several of its member companies participated in the development of Section XII, which

Page 80767

contains design requirements for tanks and pressure vessels that several of its members manufacture. [PHMSA; P-1474; Docket No. PHMSA- 2006-24712]. 3. On July 12, 2007, the National Board of Boiler and Pressure

Vessel Inspectors petitioned PHMSA to revise the HMR to incorporate by reference the National Board Inspection Code--2007 Edition. The NBIC contains rules for continued service inspections, repairs, and modifications of transport tanks, including methods to be used and criteria for inspections, reports, document control, and inspector duties and responsibilities. The term ``inspector'' includes Authorized

Inspector (AI), Qualified Inspector (QI), Certified Individual (CI) or

Registered Inspector (RI) to address all aspects of continued service.

The NBIC has updated the 2007 edition with a 2010 addendum. [P-1502;

Docket No. PHMSA-2007-28809].

IV. ASME BPVC Section XII

ASME is a not-for-profit membership professional organization that enables collaboration, knowledge-sharing, and skill development across all engineering disciplines. ASME is recognized globally for its leadership in providing the engineering community with technical content and a forum for information exchange. Development committees meet regularly to consider revisions to the ASME codes and standards based on safety concerns, technological advances, new data, and changing environmental and industry needs. All meetings are free of charge and open to public participation. ASME subcommittees consider correspondence from the general public in the form of requests for interpretation and revision to existing codes, requests for code cases, and requests to develop new standards.

In 1995, at the request of the Research and Special Programs

Administration, PHMSA's predecessor agency, the ASME Board on Pressure

Technology Codes and Standards formed a subcommittee on transport tanks

(SC XII) to develop new standards to specifically address transport tanks with active participation by PHMSA. SC XII presides over a main committee, three subgroups identified as: (1) General Requirements, (2)

Fabrication and Examination, and (3) Design and Materials.

Subsequently, SC XII developed and published in July of 2004 the ASME

BPVC Section XII, Rules for Construction and Continued Service of

Transport Tanks to address pressure vessels that are used in transportation. Section XII is based on the existing and long- established BPVC Section VIII. Section XII, 2010 edition, consists of ten parts, four modal appendices written to address different tank types, sixteen mandatory appendices, and eight non-mandatory appendices. Transport tanks are divided into categories designed specifically to mirror existing DOT specifications; for example, a DOT 406 cargo tank is a Category 406 tank in Article 1 of Modal Appendix 1.

The 2010 edition contains modal appendices for cargo tanks, cryogenic portable tanks, and ton tanks. For the purposes of this notice, PHMSA is considering a proposal to incorporate Section XII, in its entirety, for Category 331, 338, 406, 407, and 412 cargo tanks, cryogenic portable tanks, and ton tanks. PHMSA is seeking comments as to whether

Section XII should be proposed for incorporation into the HMR as an alternative or as a replacement for existing HMR requirements for DOT specification CTMVs, cryogenic portable tanks, and ton tanks.

Section VIII applies to construction of new tanks only. Tanks constructed and certified in accordance with Section VIII are marked with a ``U'' stamp. Section XII applies to new construction and continued service. As defined in Section XII, ``continued service'' is an all-inclusive term referring to the inspection, testing, repair, alteration, and recertification of transport tanks that have been in service. As stated earlier, Section XII is divided into ten parts.

PHMSA is considering incorporating all ten parts, the three modal appendices for specification cargo tanks, cryogenic portable tanks, and ton tanks, and each of the non-mandatory appendices. The ten parts are:

TG--GENERAL REQUIREMENTS; TM--MATERIAL REQUIREMENTS; TD--DESIGN

REQUIREMENTS; TW--REQUIREMENTS FOR TANKS FABRICATED BY WELDING; TF-

FABRICATION REQUIREMENTS; TE--EXAMINATION REQUIREMENTS; TT--TESTING

REQUIREMENTS; TR--PRESSURE--RELIEF DEVICES; TS--STAMPING, MARKING,

CERTIFICATION, REPORTS, AND RECORDS; and TP--REQUIREMENTS FOR REPAIR,

ALTERATION, TESTING, AND INSPECTION FOR COTINUED SERVICE. Section XII requires newly constructed transport tanks to bear a ``T'' stamp. The

``T'' stamp is essentially equivalent to the current ``U'' stamp required for certain DOT cargo tanks designed and constructed to

Section VIII standards, currently incorporated by reference in the HMR.

PHMSA is considering whether to adopt Section XII, in its entirety, as a replacement for existing DOT specification tanks, or as an alternative to the design and construction requirements for DOT specification tanks.

In this ANPRM, PHMSA refers to the 2010 edition of ASME Section

XII. However, ASME continues to work on updates to Section XII, and we will consider adoption of the most recent edition if PHMSA proceeds with a notice of proposed rulemaking (NPRM). A copy of Section XII, 2010 edition, is available for review at DOT's Docket Operations Office

(see ADDRESSES). The current price of Section XII in hard copy is $450.

V. NBIC

The National Board of Boiler and Pressure Vessel Inspectors was formed in 1921 and is an American National Standards Institute (ANSI) accredited standards development organization. The National Board follows an approved set of standards development procedures (NB-240,

National Board Inspection Code Procedures; http:// www.nationalboard.org) and is subject to regular audits by ANSI.

First published in 1946, the NBIC was established by the National

Board to provide rules and guidelines for the repair, alteration, inspection, installation, maintenance, and testing of boilers, pressure vessels, and other pressure retaining items. The NBIC is developed and maintained by a consensus committee comprised of industry experts (the

NBIC Committee). The NBIC Committee consists of a main committee, subcommittees, subgroups, and task groups of industry experts and has

Federal representation by PHMSA. Participants meet bi-annually to consider revisions to the NBIC based on safety concerns, technological advances, new data, and industry needs. All meetings are free of charge and open to public participation. The NBIC subcommittees consider correspondence from the general public in the form of requests for interpretation and revision of existing standards and requests to develop new standards. The standards-writing subcommittees, subgroups, and task groups are open to participation by representatives of groups that are materially affected by the code. Such groups include manufacturers, repair firms, authorized inspection agencies, and representatives of government agencies. Each year the NBIC Committee updates the NBIC and presents the updates on the National Board's website for public review in April-May and August-September. Finalized updates are published annually as an addendum.

Section XII requires all alterations and repairs to the pressure vessel of a

Page 80768

transport tank to be performed in accordance with the NBIC and requires an inspection to be performed by a National Board inspector. The NBIC

Committee established a task group to develop requirements for continued service, repair, and alteration of Section XII transport tanks. The task group includes PHMSA and industry representatives. The

Committee's efforts culminated in the issuance of two new supplements.

The first is Supplement 6, ``Continued Service and Inspection of DOT

Transport Tanks.'' This appears in Section 6, ``Supplements'' of Part 2, ``Inspection.'' This document describes inspection of in service transport tanks. The second is Supplement 6, ``Repair, Alteration, and

Modification of DOT Transport Tanks.'' This appears in Section 6,

``Repairs and Alterations--Supplements'' of Part 3--``Repair.'' This document contains general requirements that apply to welding, repairs, alterations, modifications, examinations, etc. made to DOT transport tanks used for the transportation of hazardous materials. These supplements also specify the type of inspection to be performed and establish the criteria for inspections, reports, document maintenance, and inspector duties and responsibilities. The criteria are generally based on requirements in Part 180 of the HMR.

PHMSA is considering whether to adopt the NBIC for alterations, repairs and inspections performed on ASME stamped portable tanks, specification cargo tanks, and ton tanks used for the transportation of hazardous materials. In this ANPRM, we refer to the 2007 edition of the

NBIC and the 2010 addendum. However, the National Board continues to work on updates to the NBIC, and PHMSA will consider adoption of the most recent edition if we proceed with an NPRM. A copy of the 2007 edition of the NBIC is available for review at DOT's Docket Operations

Office (see ADDRESSES appearing earlier in this notice). The current cost of the complete NBIC set is $150 for the hard copy and $395 for the electronic format.

VI. Voluntary Consensus Standards

The ASME BPVC and the NBIC are international voluntary consensus standards. The National Technology Transfer and Advancement Act of 1995, Public Law 104-113, requires agencies to use technical standards that are developed or adopted by voluntary consensus standards bodies unless the use of such a standard is inconsistent with applicable law or is otherwise impractical. Public Law 104-113 requires Federal agencies to use industry consensus standards to the extent practical; it does not require Federal agencies to endorse a standard in its entirety. The law does not prohibit an agency from generally adopting a voluntary consensus standard while taking exception to specific portions of the standard if those provisions are deemed to be

``inconsistent with applicable law or otherwise impractical.'' Taking specific exceptions furthers the Congressional intent of Federal reliance on voluntary consensus standards because it allows the adoption of substantial portions of consensus standards without the need to reject the standards in their entirety because of limited provisions that are not acceptable to the agency. It has been PHMSA's practice to review new editions and addenda of the ASME BPVC and NBIC and periodically update Sec. 171.7 to incorporate newer editions and addenda by reference. New editions of the subject codes are issued every three years; addenda to the editions are issued yearly except in years when a new edition is issued. The BPVC was last incorporated by reference into the regulations under Docket No. RSPA-99-6213 (HM-218)

(August 18, 2000; 65 FR 50450). In that final rule, Sec. 171.7 was revised to incorporate by reference the 1998 edition of Sections II

(Parts A and B), V, VIII (Division I) and IX, of the BPVC. The NBIC 1992 Edition was incorporated by reference under Docket HM-183C

(November 3, 1994; 59 FR 55162).

VII. Current HMR, Section XII, and NBIC Requirements

1. Design and Construction of Cryogenic Portable Tanks

   Sections 178.274 and 178.277 of the HMR contain requirements for the design, construction, certification, inspection, and testing of UN portable tanks intended for the transportation of refrigerated liquefied gases. The HMR requires that the shells and welds of these portable tanks must be designed, constructed, certified, inspected, tested and stamped in accordance with Section VIII of the BPVC. BPVC

   Section XII includes rules for the design, construction, certification, inspection, and testing of cryogenic portable tanks that address conditions and stresses unique to the transportation of cryogenic portable tanks. However, Section XII differs from the HMR with respect to design margins for cryogenic portable tanks (i.e., 3.5:1 rather than 4.0:1). The 3.5:1 design margin is based upon successful experience with vessels designed to the Code rules, improved materials and fabrication practices, new and more sophisticated design methods, toughness requirements, and nondestructive examination technology.

   PHMSA believes that adopting this new design margin by incorporating

   Section XII in the HMR would update current regulations in recognition of the technological enhancements referred to above, maintain an equivalent level of safety to existing regulations, and relieve unnecessary economic burden to manufacturers and users of cryogenic portable tanks by allowing for the design and construction of thinner walled tanks. Therefore, PHMSA is considering whether to permit the design, construction, certification, inspection, and testing of UN portable tanks intended for the transportation of refrigerated liquefied gases in accordance with Section XII.

2. Design and Construction of CTMVs: Identified Differences Between HMR and Section XII Requirements

   Sections 178.337-178.348 of the current HMR contain requirements for the design, construction, certification, inspection, and testing of

   CTMVs intended for the transportation of hazardous materials. CTMVs conforming to the MC 331, MC 338, and DOT 407 specifications with a maximum allowable working pressure (MAWP) greater than 35 psig or designed to be loaded by vacuum, and to the DOT 412 specification with a MAWP greater than 15 psig must be designed, constructed, and certified in accordance with Section VIII, Division 1 of the 1998 ASME

   Code. As defined in Sec. 173.320, the term ``constructed and certified in accordance with the ASME Code'' means a cargo tank is constructed and stamped in accordance with the ASME Codes and is inspected and certified by an AI. CTMVs conforming to the DOT 406, and the lower pressure DOT 407 and 412 specifications must be constructed in accordance with the ASME Code. The term ``constructed in accordance with the ASME Code'' means a cargo tank is constructed in accordance with Section VIII, Division 1 of the ASME Codes with authorized exceptions and is inspected and certified by a RI. The manufacturer of the cargo tank or CTMV must hold a current ASME Certificate for use of the ASME ``U'' stamp but the tank is not required to be ASME stamped.

   Under Section XII, all newly manufactured cryogenic portable tanks and specification CTMVs constructed in accordance with the Code must be stamped with a ``T'' stamp.

   The Section XII requirements were harmonized with the HMR requirements to the extent practicable. During the development of

   Section XII, the SC XII

   Page 80769

   committees addressed various cargo tank concerns that industry brought to the attention of PHMSA and FMCSA, over the past several years.

   At the request of PHMSA, ASME supplemented its original petition for rulemaking with information identifying particular differences between Section XII and the HMR requirements. PHMSA encourages commenters to review and comment on these and any other differences between ASME Section XII and the HMR that are relevant to this endeavor. In addition, the Docket for this ANPRM includes several reports containing research, analysis, and evaluation of various technical standards that have been adopted in ASME Section XII. 1. 3.5 Design Margin in Lieu of 4.0 for All Vessels

   Improvements to Section VIII Division 1 Code rules over the past 50 years, successful experience with vessels designed to the Code rules, improved materials and fabrication practices, new and more sophisticated design methods, toughness requirements, and nondestructive examination technology have led to a reduced design margin in Section VIII, Division 1. In 1999, ASME adopted a design margin of 3.5 on ultimate tensile strength in lieu of the value of 4.0 that had existed since the 1940s. In Section XII, ASME adopted the new design margin after careful consideration and deliberations of the technical facts previously mentioned as well as other factors that influence transportation safety.

   The new design margins may have a significant effect on newly constructed transport tanks. For those tanks where the minimum thicknesses are controlled by pressure, they may be thinner/lighter than those constructed using a design margin of 4.0. PHMSA has issued several special permits allowing a 3.5:1 design margin. PHMSA has reviewed the incident data for these tanks and has not identified any incidents that would indicate a reduction in safety. PHMSA is soliciting comments on potential safety and economic impacts of adopting the new Section XII requirement allowing a 3.5:1 design margin. 2. Special Materials Testing and Fabrication Requirements for MC 331

   Tanks

   Section XII Modal Appendix 1-- ``Cargo Tanks'' discontinues certain obsolete requirements for construction of MC 331 cargo tanks that are still required in Sec. Sec. 178.337-2 and 178.337-4. This revision modernizes material specification designations and eliminates obsolete material specifications. It also eliminates certain obsolete material impact test requirements, especially for quenched and tempered materials. PHMSA has issued several special permits allowing the use of the newer material specifications in the ASME Code for construction and repair. A review of historical incident data shows an acceptable safety history with no reported incidents. PHMSA is soliciting comments on the safety and economic impacts of adopting the new Section XII reqirements for the testing and fabrication of special materials for construction and repair of MC 331 cargo tanks. 3. Standardization of Allowable Peak Secondary Stresses for MC 331

   CargoTanks

   The requirements in Modal Appendix 1-3.5.5 and 1-3.5.1(a)(1)(b) standardize the allowable peak secondary stress levels resulting from short interval, non-persistent loads to that permitted for lading surge loads for MC 331 cargo tanks by Sec. 178.337-3(d). See also 1-3.5.5 & 1-3.5.6 and footnote 1. The Appendix also aligns the MC 331 cargo tank design with the design standard of the DOT 400-series cargo tanks for short interval peak loads. PHMSA-sponsored research and guidance, and understanding of current ASME requirements, provide the basis for consideration of this revision. PHMSA solicits comments on the safety and economic impacts of adopting the Section XII requirement for allowable peak secondary stresses for MC 331 cargo tanks. 4. Rational Design of Non-circular Tanks

   Rational design under Appendix VIII of Section XII leads to shell and head thicknesses of up to 15% less than what tank manufacturers currently use. Such a difference results in a tank with at least 2% more payload capacity. Co-operative research and development efforts by

   PHMSA, ASME, and industry have served as the technical basis for incorporation of the rational design method in Section XII. PHMSA is soliciting comments on the safety and economic impacts of incorporating the Section XII rational design method for non-circular tanks. 5. Non Mandatory Appendix C--Specified Minimum Thicknesses

   Non-mandatory Appendix C contains data reports that specify minimum allowed thickness for pressure parts instead of nominal thickness and corrosion allowance currently specified. PHMSA is soliciting comments on the safety and economic impacts of using minimum allowed thickness for pressure parts instead of nominal thickness and corrosion allowance.

3. Continued Service of CTMVs, Portable Tanks, and Ton Tanks: Roles of

   Inspectors HMR

   Part 180 of the HMR specifies continued service requirements for

   DOT and UN portable tanks and DOT specification and certain non- specification CTMVs. Specific requirements for the qualification, maintenance, repair, and testing of packagings are located in 49 CFR

   Part 180: Subpart E for CTMVs, Subpart F for ton tanks, and Subpart G for portable tanks. Incorporation of Section XII and the NBIC for continued service requirements for these ASME stamped bulk packagings could impact the roles and responsibilities of persons who perform tests, inspections, modifications, alterations, and repairs. PHMSA is soliciting comments on how the continued service requirements and the role of inspectors should be addressed in the HMR if Section XII and the NBIC are incorporated by reference.

   To ensure that DOT specification cargo tanks are designed, constructed, and maintained in accordance with the applicable specification, the HMR require that each person who certifies CTMV design, construction, repair, or testing meet certain minimum qualifications. The qualification criteria are based on the function performed. Professionals who meet the qualifications set forth in the

   HMR for DCE, AI, and RI perform continued service functions.

   The HMR require the use of a DCE to certify each specification cargo tank or CTMV design type, including its required accident damage protection; the design of a modified, stretched, or rebarrelled CTMV; or mounting of a cargo tank on a motor vehicle chassis involving welding on the cargo tank head or shell or any change or modification of the methods of attachment. A DCE as defined in Sec. 171.8 means a person registered with the Department in accordance with subpart F of part 107 of the HMR who has the knowledge and ability to perform stress analysis of pressure vessels and otherwise determine whether a cargo tank design and construction meets the applicable DOT specification. A

   DCE must fulfill the knowledge and ability requirements by meeting any one of the following qualifications: (1) Have an engineering degree and one year of work experience in cargo tank structural or mechanical design: (2) be currently registered as a professional engineer by appropriate authority of a State of the United States or a Province of

   Canada;

   Page 80770

   or (3) have at least three years' experience in performing the duties of a DCE prior to September 1, 1991.

   Additionally, the HMR require the use of an AI to certify cargo tanks constructed and certified in accordance with the ASME Code, as discussed earlier in this notice under ``B. Design and Construction of

   CTMVs: Identified Differences Between HMR and Section XII

   Requirements.'' An AI is defined in Sec. 171.8 to mean an Inspector who is currently commissioned by the National Board of Boiler and

   Pressure Vessel Inspectors and employed as an Inspector by an

   Authorized Inspection Agency. Also, this section defines an Authorized

   Inspection Agency to mean: (1) A jurisdiction which has adopted and administers one or more sections of the ASME Boiler and Pressure Vessel

   Code as a legal requirement and has a representative serving as a member of the ASME Conference Committee; or (2) an insurance company which has been licensed or registered by the appropriate authority of a

   State of the United States or a Province of Canada to underwrite boiler and pressure vessel insurance in such State or Province.

   The HMR require the use of an RI to certify specification cargo tank motor vehicle construction, assembly, or repair of a tank

   ``constructed in accordance with the ASME Code.'' Section 171.8 defines the RI as a person registered with the Department in accordance with subpart F of part 107 of the HMR who has the knowledge and ability to determine whether a cargo tank conforms to the applicable DOT specification. The RI must have: (1) An engineering degree and one year of work experience relating to the testing and inspection of cargo tanks; (2) an associate degree in engineering and two years of work experience relating to the testing and inspection of cargo tanks; (3) a high school diploma (or General Equivalency Diploma) and three years of work experience relating to the testing and inspection of cargo tanks; or (4) at least three years of experience performing the duties of an

   RI prior to September 1, 1991. The RI must be familiar with DOT specification cargo tanks and trained and experienced in use of the inspection and testing equipment used. While there are narrow exceptions that permit persons who do not qualify as RIs to perform select inspections and tests (see Sec. 180.409(b), (c), and (d)), in general, a cargo tank constructed in accordance with a DOT specification for which a qualification test or inspection is due, may not be filled and offered for transportation or transported until the test or inspection has been successfully completed by the RI.

   Section XII

   Section XII requires all alterations and repairs to the pressure vessel of a transport tank to be performed in accordance with the NBIC and requires an inspection to be performed by a National Board inspector. The inspector, depending on the class designation of the transport tank, must be an Authorized Inspector (AI), Qualified

   Inspector (QI), or Certified Individual (CI).

   Under Section XII, an AI is defined as an inspector regularly employed by an ASME-accredited Authorized Inspection Agency (AIA), who has been qualified to ASME-developed criteria to perform inspections under the rules of any jurisdiction that has adopted the ASME Code. The

   AI may not be in the employ of the manufacturer. The AIA's and supervisor's duties and qualifications and AI's qualifications are as required in the latest edition and addenda of ASME QAI-1,

   Qualifications for Authorized Inspection. Under ASME QAI-1, An

   Authorized Inspector must hold a valid Certificate of Competency (where required), as defined in National Board Rules for Commissioned

   Inspectors, and a valid National Board Commission with an ``A'' endorsement. The inspector must have satisfactory expertise, experience, and background for the inspection of boilers and pressure vessels and demonstrate the ability to perform shop and field (on-site) inspections to the satisfaction of the AIA. The inspector must have knowledge of applicable sections of the ASME Code, Quality Control

   Programs, and requirements for the maintenance and retention of in- transit and permanent records. Finally, the inspector must receive a passing grade on an examination given by the National Board that evaluates the individual's knowledge of, and familiarity with, the ASME

   Code, and comply with the National Board's rules for commissioned inspectors.

   A QI is defined as an inspector regularly employed by an ASME

   Qualified Inspection Organization (QIO) who has been qualified to ASME- developed criteria by a written examination, to perform inspections under the rules of any jurisdiction that has adopted the ASME Code. The

   QI may not be in the employ of the manufacturer. The QIO's and supervisor's duties and qualifications and the QI's qualifications are as required in the latest edition and addenda of ASME QAI-1,

   Qualifications for Authorized Inspection. Under ASME QAI-1, a Qualified

   Inspector must hold a valid Certificate of Competency (where required), as defined in National Board Rules for Commissioned Inspectors, and a valid National Board certification as a Qualified Inspector. The inspector must have satisfactory expertise, experience, and background for the inspection of boilers and pressure vessels and demonstrate the ability to perform shop and field (on-site) inspections to the satisfaction of the QIA. The inspector must have knowledge of applicable sections of the ASME Code, Quality Control Programs, and requirements for the maintenance and retention of in-transit and permanent records. Finally, the inspector must receive a passing grade on an examination given by the National Board that evaluates the individual's knowledge of, and familiarity with, the ASME Code. The

   Qualified Inspector must comply with the National Board's rules for qualified inspectors.

   A CI is defined as an individual certified by an ASME accredited organization authorized to use ASME marks, as either a full-time or part-time employee or contractor to the ASME certificate holder. The CI is neither an AI nor a QI and must be certified and qualified to perform inspections by the CI's employer. The CI may be in the employ of the manufacturer or assembler. Minimum qualifications include: (a)

   Knowledge of the requirements of Section XII for application of the appropriate Code Symbol stamp; (b) Knowledge of the Manufacturer's or

   Assembler's Quality System Program; and (c) Training commensurate with the scope, complexity, or special nature of the activities to which oversight is to be provided. A record must be maintained and certified by the manufacturer or assembler, containing objective evidence of the qualifications of the CI and training provided the CI's qualifications and duties are as required in the latest edition and addenda of ASME

   QAI-1, Qualifications for Authorized Inspection.

   Additionally, for continued service, Users may perform inspections and tests if no rerating, repairs, or alterations requiring welding are performed. Users may perform continued service inspections, including repairs and alterations if the User possesses a valid National Board

   Owner/User Certificate of Authorization. Inspectors employed by the

   Owner/User may perform continued service inspections, including repairs and alterations if the individual possesses a National Board Owner/User commission.

   Page 80771

   Section XII assigns transport tanks to three separate classes depending on the design of the tank. Each class includes transport tank designs that generally correspond to existing DOT specifications. The

   NBIC inspection requirements correspond to the class of transport tank as assigned in the Section XII Modal Appendices. In the table below,

   PHMSA lists each class of transport tank to be constructed or repaired and the type of inspector required to perform the inspection. Currently there are no specifications in Section XII for Class 2 tanks. However,

   Class 2 tanks are expected to be added in future editions.

   Transport Tank Classes Under ASME Section XII, 2010 Edition

   Current

   Class

   specification in

   Type of inspector

   HMR

   Class 1......................... UN cryogenic

   Authorized portable tanks

   Inspector

   (See Sec. 178.277); DOT 407

   MAWP > 35 psi

   (See Sec. 178.347); DOT 412

   MAWP > 15 psi

   (See Sec. 178.348); MC 338

   (See Sec. 178.338); MC 331

   (See Sec. 178.337); DOT 106A and 110AW

   (See Sec. 179.300).

   Class 2......................... .................. Qualified

   Inspector , or

   Authorized

   Inspector

   Class 3......................... DOT 406 (See Sec. Certified 178.346); DOT

   Individual, 407 MAWP