Petition for Decision that Nonconforming 2006 BMW M3 Passenger Cars Manufactured Before September 1, 2006 are Eligible for Importation
Federal Register: June 3, 2009 (Volume 74, Number 105)
Notices
Page 26762-26764
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
DOCID:fr03jn09-127
DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
Docket No. NHTSA-2009-0102
Notice of Receipt of Petition for Decision That Nonconforming 2006 BMW M3 Passenger Cars Manufactured Before September 1, 2006 Are
Eligible for Importation
AGENCY: National Highway Traffic Safety Administration, DOT.
ACTION: Notice of receipt of petition for decision that nonconforming 2006 BMW M3 passenger cars manufactured before September 1, 2006 are eligible for importation.
SUMMARY: This document announces receipt by the National Highway
Traffic Safety Administration (NHTSA) of a petition for a decision that 2006 BMW M3 passenger cars manufactured before September 1, 2006 that were not originally manufactured to comply with all applicable Federal motor vehicle safety standards (FMVSS) are eligible for importation into the United States because (1) they are substantially similar to vehicles that were originally manufactured for sale in the United
States and that were certified by their manufacturer as complying with the safety standards (the U.S.-certified version of the 2006 BMW M3 passenger cars manufactured before September 1, 2006) and (2) they are capable of being readily altered to conform to the standards.
DATE: The closing date for comments on the petition is July 6, 2009.
ADDRESSES: Comments should refer to the docket and notice numbers above and be submitted by any of the following methods:
Federal eRulemaking Portal: Go to http:// www.regulations.gov. Follow the online instructions for submitting comments.
Mail: Docket Management Facility: U.S. Department of
Transportation, 1200 New Jersey Avenue, SE., West Building Ground
Floor, Room W12-140, Washington, DC 20590-0001.
Hand Delivery or Courier: West Building Ground Floor, Room
W12-140, 1200 New Jersey Avenue, SE., between 9 a.m. and 5 p.m. ET,
Monday through Friday, except Federal holidays.
Page 26763
Fax: 202-493-2251.
Instructions: Comments must be written in the English language, and be no greater than 15 pages in length, although there is no limit to the length of necessary attachments to the comments. If comments are submitted in hard copy form, please ensure that two copies are provided. If you wish to receive confirmation that your comments were received, please enclose a stamped, self-addressed postcard with the comments. Note that all comments received will be posted without change to http://www.regulations.gov, including any personal information provided. Please see the Privacy Act heading below.
Privacy Act: Anyone is able to search the electronic form of all comments received into any of our dockets by the name of the individual submitting the comment (or signing the comment, if submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy Act Statement in the Federal Register published on
April 11, 2000 (65 FR 19477-78) or you may visit http://
DocketInfo.dot.gov.
How To Read Comments Submitted to the Docket: You may read the comments received by Docket Management at the address and times given above. You may also see the comments on the Internet. To read the comments on the Internet, take the following steps:
(1) Go to the Federal Docket Management System (FDMS) Web page http://www.regulations.gov.
(2) On that page, click on ``Advanced Docket Search.''
(3) On the next page select ``NATIONAL HIGHWAY TRAFFIC SAFETY
ADMINISTRATION'' from the drop-down menu in the Agency field and enter the Docket ID number shown at the heading of this document.
(4) After entering that information, click on ``submit.''
(5) The next page contains docket summary information for the docket you selected. Click on the comments you wish to see. You may download the comments. Please note that even after the comment closing date, we will continue to file relevant information in the Docket as it becomes available. Further, some people may submit late comments.
Accordingly, we recommend that you periodically search the Docket for new material.
FOR FURTHER INFORMATION CONTACT: Coleman Sachs, Office of Vehicle
Safety Compliance, NHTSA (202-366-3151).
SUPPLEMENTARY INFORMATION:
Background
Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not originally manufactured to conform to all applicable FMVSS shall be refused admission into the United States unless NHTSA has decided that the motor vehicle is substantially similar to a motor vehicle originally manufactured for importation into and sale in the United
States, certified under 49 U.S.C. 30115, and of the same model year as the model of the motor vehicle to be compared, and is capable of being readily altered to conform to all applicable FMVSS.
Petitions for eligibility decisions may be submitted by either manufacturers or importers who have registered with NHTSA pursuant to 49 CFR Part 592. As specified in 49 CFR 593.7, NHTSA publishes notice in the Federal Register of each petition that it receives, and affords interested persons an opportunity to comment on the petition. At the close of the comment period, NHTSA decides, on the basis of the petition and any comments that it has received, whether the vehicle is eligible for importation. The agency then publishes this decision in the Federal Register.
Wallace Environmental Testing Laboratories, Inc. (WETL) of Houston,
TX (Registered Importer 90-005) has petitioned NHTSA to decide whether nonconforming 2006 BMW M3 passenger cars manufactured before September 1, 2006 are eligible for importation into the United States. The vehicles which WETL believes are substantially similar are 2006 BMW M3 passenger cars manufactured before September 1, 2006 that were manufactured for sale in the United States and certified by their manufacturer as conforming to all applicable FMVSS.
The petitioner claims that it compared non-U.S. certified 2006 BMW
M3 passenger cars manufactured before September 1, 2006 to their U.S.- certified counterparts, and found the vehicles to be substantially similar with respect to compliance with most FMVSS.
WETL submitted information with its petition intended to demonstrate that non-U.S. certified 2006 BMW M3 passenger cars manufactured before September 1, 2006, as originally manufactured, conform to many FMVSS in the same manner as their U.S. certified counterparts, or are capable of being readily altered to conform to those standards.
Specifically, the petitioner claims that non-U.S. certified 2006
BMW M3 passenger cars manufactured before September 1, 2006 are identical to their U.S. certified counterparts with respect to compliance with Standard Nos. 102 Transmission Shift Lever Sequence,
Starter Interlock, and Transmission Braking Effect, 103 Windshield
Defrosting and Defogging Systems, 104 Windshield Wiping and Washing
Systems, 106 Brake Hoses, 109 New Pneumatic Tires, 113 Hood Latch
System, 116 Motor Vehicle Brake Fluids, 118 Power-Operated Window,
Partition, and Roof Panel Systems, 124 Accelerator Control Systems, 135
Passenger Car Brake Systems, 201 Occupant Protection in Interior
Impact, 202 Head Restraints, 204 Steering Control Rearward
Displacement, 205 Glazing Materials, 206 Door Locks and Door Retention
Components, 207 Seating Systems, 209 Seat Belt Assemblies, 210 Seat
Belt Assembly Anchorages, 212 Windshield Mounting, 214 Side Impact
Protection, 216 Roof Crush Resistance, 219 Windshield Zone Intrusion, 225 Child Restraint Anchorage Systems, 302 Flammability of Interior
Materials, and 401 Interior Trunk Release.
In addition, the petitioner claims that the vehicles comply with the Bumper Standard found in 49 CFR Part 581.
The petitioner also contends that the vehicles are capable of being readily altered to meet the following standards, in the manner indicated:
Standard No. 101 Controls and Displays: inscription of the word
``brake'' on the instrument cluster in place of the international ECE warning symbol and installation of a U.S.-model speedometer, or modification of the existing speedometer to conform with the requirements of this standard.
Standard No. 108 Lamps, Reflective Devices and Associated
Equipment: installation of U.S.-model high mounted stop lamp and associated wiring.
Standard No. 110 Tire Selection and Rims: installation of a tire information placard on all vehicles not already so equipped.
Standard No. 111 Rearview Mirrors: installation of a U.S.-model passenger side rearview mirror, or inscription of the required warning statement on the face of that mirror on all vehicles not already so equipped.
Standard No. 114 Theft Protection: installation of a supplemental key warning buzzer, or installation of U.S.-version software on all vehicles not already so equipped.
Standard No. 208 Occupant Crash Protection: installation of a seat belt warning system that the meets the requirements of this standard.
The petitioner states that the crash protection system used in these vehicles
Page 26764
consists of dual front airbags, knee bolsters, and combination lap and shoulder belts at the front outboard seating positions.
Standard No. 301 Fuel System Integrity: inspection of all vehicles and replacement of any non U.S.-model fuel system components with U.S.- model components.
The petitioner additionally states that a vehicle identification plate must be affixed to the vehicles near the left windshield post to meet the requirements of 49 CFR Part 565.
All comments received before the close of business on the closing date indicated above will be considered, and will be available for examination in the docket at the above addresses both before and after that date. To the extent possible, comments filed after the closing date will also be considered. Notice of final action on the petition will be published in the Federal Register pursuant to the authority indicated below.
Authority: 49 U.S.C. 30141(a)(1)(A) and (b)(1); 49 CFR 593.8; delegations of authority at 49 CFR 1.50 and 501.8.
Issued on: May 27, 2009.
Claude H. Harris,
Director, Office of Vehicle Safety Compliance.
FR Doc. E9-12841 Filed 6-2-09; 8:45 am
BILLING CODE 4910-59-P
