Air pollutants, hazardous; national emission standards: Organic liquids distribution (non-gasoline),

As Enacted ( Federal Register)

Cited authorities 27

Cited in

[Federal Register: November 14, 2005 (Volume 70, Number 218)]

[Proposed Rules]

[Page 69209-69237]

From the Federal Register Online via GPO Access [wais.access.gpo.gov]

[DOCID:fr14no05-30]

[[Page 69209]]

Part II

Environmental Protection Agency

40 CFR Part 63

National Emission Standards for Hazardous Air Pollutants: Organic Liquids Distribution (Non-Gasoline); Proposed Rule

[[Page 69210]]

ENVIRONMENTAL PROTECTION AGENCY

40 CFR Part 63

[OAR-2003-0138, FRL-7993-7]

RIN 2060-AM77

National Emission Standards for Hazardous Air Pollutants: Organic Liquids Distribution (Non-Gasoline)

AGENCY: Environmental Protection Agency (EPA).

ACTION: Proposed rule; amendments.

SUMMARY: On February 3, 2004 (69 FR 5038), the EPA issued national emission standards for hazardous air pollutants for organic liquids distribution (non-gasoline) (OLD NESHAP) under section 112 of the Clean Air Act (CAA). In this action, EPA is proposing to amend portions of the OLD NESHAP in response to petitions for judicial review and for administrative reconsideration of the promulgated rule. The proposed amendments are being made to clarify the applicability and control requirements for storage tanks and transfer racks, and amend the recordkeeping and reporting requirements for affected sources for which there are no control requirements. The proposed amendments do not reflect the full set of possible amendments EPA intends to propose in response to all of the issues raised in the petitions for review and reconsideration. The Agency is separately developing a proposed response to some of those issues.

DATES: Comments. Submit comments on or before December 29, 2005.

Public Hearing. If a public hearing is requested by November 25, 2005, the EPA will hold a public hearing by November 29, 2005. To request a public hearing, contact Ms. Martha Smith, EPA, Waste and Chemical Processes Group (C439-03), Emission Standards Division, Office of Air Quality Planning and Standards, Research Triangle Park, North Carolina 27711, telephone number (919) 541-2421, facsimile number (919) 541-0246, electronic mail address: smith.martha@epa.gov.

ADDRESSES: Comments. Submit your comments, identified by Docket ID No. OAR-2003-0138, by one of the following methods:

Federal eRulemaking Portal: http://www.regulations.gov.

Follow the on-line instructions for submitting comments.

Agency Web site: http://www.epa.gov/edocket. EDOCKET,

EPA's electronic public docket and comment systems, is EPA's preferred method for receiving comments. Follow the on-line instructions for submitting comments.

Fax: 202-566-1741

Mail: (in duplicate, if possible) to Air and Radiation Docket, Environmental Protection Agency, Mailcode: 6102T, 1200 Pennsylvania Avenue, NW., Washington, DC 20460.

Hand Delivery: (in duplicate, if possible) to: Air and Radiation Docket, Attention Docket ID Number OAR-2003-0138, EPA, 1301 Constitution Avenue, NW., Room B-102, Washington, DC 20460. Such deliveries are only accepted during the Docket's normal hours of operation, and special arrangements should be made for deliveries of boxed information.

We request that a separate copy also be sent to the contact person listed below (see FOR FURTHER INFORMATION CONTACT).

Instructions: Direct your comments to Docket ID No. OAR-2003-0138. EPA's policy is that all comments received will be included in the public docket without change and may be made available online at http://www.epa.gov/edocket , including any personal information provided,

unless the comment includes information claimed to be Confidential Business Information (CBI) or other information whose disclosure is restricted by statute. Do not submit information that you consider to be CBI or otherwise protected through EDOCKET, regulations.gov, or e- mail. The EPA EDOCKET and the Federal regulations.gov Web sites are ``anonymous access'' systems, which means EPA will not know your identity or contact information unless you provide it in the body of your comment. If you send an e-mail comment directly to EPA without going through EDOCKET or regulations.gov, your e-mail address will be automatically captured and included as part of the comment that is placed in the public docket and made available on the Internet. If you submit an electronic comment, EPA recommends that you include your name and other contact information in the body of your comment and with any disk or CD-ROM you submit. If EPA cannot read your comment due to technical difficulties and cannot contact you for clarification, EPA may not be able to consider your comment. Electronic files should avoid the use of special characters, any form of encryption, and be free of any defects or viruses. For additional information about EPA's public docket visit EDOCKET on-line or see the Federal Register of May 31, 2002 (67 FR 38102). For additional instructions on submitting comments, go to the SUPPLEMENTARY INFORMATION section of this document.

Docket: All documents in the docket are listed in either the EDOCKET index at http://www.epa.gov/edocket or in the legacy docket, A-

98-13. Although listed in the index, some information is not publicly available, i.e., CBI or other information whose disclosure is restricted by statute. Certain other material, such as copyrighted material, is not placed on the Internet and will be publicly available only in hard copy form. Publicly available docket materials are available either electronically in EDOCKET or in hard copy at the Air and Radiation Docket, EPA/DC, EPA West, Room B102, 1301 Constitution Ave., NW., Washington, DC. The Public Reading Room is open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. A reasonable fee may be charged for copying docket materials. The telephone number for the Public Reading Room is (202) 566-1744, and the telephone number for the Air and Radiation Docket is (202) 566-1742.

Public Hearing. If a public hearing is held, it will be held at 10 a.m. at the EPA facility complex in Research Triangle Park, North Carolina, or at an alternate site nearby.

FOR FURTHER INFORMATION CONTACT: Ms. Martha Smith, EPA, Waste and Chemical Processes Group (C439-03), Emission Standards Division, Office of Air Quality Planning and Standards, Research Triangle Park, North Carolina 27711, telephone number (919) 541-2421, facsimile number (919) 541-3207, electronic mail address: smith.martha@epa.gov.

SUPPLEMENTARY INFORMATION: Regulated Entities. Categories and entities potentially regulated by this action include:

[[Page 69211]]

NAICS * Category

code SIC * code Examples of regulated entities

Industry......................................... 325211

2821 Operations at major sources that 325192

2865 transfer organic liquids into or 325188

2869 out of the plant site, including: 32411

2911 liquid storage terminals, crude 49311

4226 oil pipeline stations, petroleum 49319

4612 refineries, chemical manufacturing 48611

5169 facilities, and other 42269

5171 manufacturing facilities with 42271

collocated OLD operations. Federal Government............................... ........... ........... Federal agency facilities that operate any of the types of entities listed under the ``industry'' category in this table.

* Considered to be the primary industrial codes for the plant sites with OLD operations.

This table is not intended to be exhaustive, but rather provides a guide for readers regarding entities likely to be regulated by this action. To determine whether your facility is regulated by this action, you should examine the applicability criteria 40 CFR part 63, subpart EEEE. If you have any questions regarding the applicability of this action to a particular entity, consult the individual described in the preceding FOR FURTHER INFORMATION CONTACT section.

Submitting Comments Containing CBI. Do not submit this information to EPA through EDOCKET, regulations.gov or e-mail. Clearly mark the part or all of the information that you claim to be CBI. For CBI information in a disk or CD ROM that you mail to EPA, mark the outside of the disk or CD ROM as CBI and then identify electronically within the disk or CD ROM the specific information that is claimed as CBI. In addition to one complete version of the comment that includes information claimed as CBI, a copy of the comment that does not contain the information claimed as CBI must be submitted for inclusion in the public docket. Information so marked will not be disclosed except in accordance with procedures set forth in 40 CFR part 2.

Tips for Preparing Your Comments. When submitting comments, remember to:

Identify the rulemaking by docket number and other identifying information (subject heading, Federal Register date and page number).

Follow directions--The agency may ask you to respond to specific questions or organize comments by referencing a Code of Federal Regulations (CFR) part or section number.

Explain why you agree or disagree; suggest alternatives and substitute language for your requested changes.

Describe any assumptions and provide any technical information and/or data that you used.

If you estimate potential costs or burdens, explain how you arrived at your estimate in sufficient detail to allow for it to be reproduced.

Provide specific examples to illustrate your concerns, and suggest alternatives.

Explain your views as clearly as possible, avoiding the use of profanity or personal threats.

Make sure to submit your comments by the comment period deadline identified.

Worldwide Web (WWW). In addition to being available in the docket, an electronic copy of this action will also be available through the http://WWW. Following signature, a copy of this action will be posted on EPA's

Technology Transfer Network (TTN) policy and guidance page for newly proposed or promulgated rules: http://www.epa.gov/ttn/oarpg. The TTN at

EPA's Web site provides information and technology exchange in various areas of air pollution control.

Public Hearing. Persons interested in presenting oral testimony or inquiring as to whether a hearing is to be held should contact Ms. Martha Smith, Waste and Chemical Processes Group, Emission Standards Division, (C439-04), Research Triangle Park, NC 27711, telephone number (919) 541-2421, at least 2 days in advance of the potential date of the public hearing. Persons interested in attending the public hearing must also call Ms. Smith to verify the time, date, and location of the hearing. The public hearing will provide interested parties the opportunity to present data, views, or arguments concerning the proposed emissions standards.

Outline. The following outline is provided to aid in reading this preamble to the proposed rule amendments.

Background II. Proposed Amendments to the Organic Liquids Distribution NESHAP
1. How are definitions being revised?
2. How are control options being revised?
3. How Are My Notification, Recordkeeping, and Reporting Requirements Being Revised?
4. How are compliance requirements being changed?
5. How is the affected source being changed?
6. Miscellaneous Edits III. Statutory and Executive Order Reviews
7. Executive Order 12866: Regulatory Planning and Review
8. Paperwork Reduction Act
9. Regulatory Flexibility Act
10. Unfunded Mandates Reform Act
11. Executive Order 13132: Federalism
12. Executive Order 13175: Consultation and Coordination with Indian Tribal Governments
13. Executive Order 13045: Protection of Children From Environmental Health Risks and Safety Risks
14. Executive Order 13211: Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use
National Technology Transfer and Advancement Act
Background

On February 3, 2004 (69 FR 5063), the Federal Register published EPA's National Emission Standards for Hazardous Air Pollutants: Organic Liquids Distribution (Non-Gasoline) (40 CFR part 63, subpart EEEE). Subpart EEEE sets emission limits and work practice standards for storage tanks, transfer racks, equipment leak components in organic liquid service, transport vehicles, and containers. These standards identify several control options for storage tanks and transfer racks that meet certain criteria. Because storage tanks and transfer racks in OLD operation may also be covered by other existing NESHAP, subpart EEEE addresses these overlap situations. Finally, subpart EEEE also contains notification, recordkeeping, and reporting requirements.

Since publication of the OLD NESHAP, EPA has received several petitions for administrative reconsideration of the OLD NESHAP, and several petitions for judicial review have been filed in the U.S. Court of Appeals for the DC Circuit. Petitions for reconsideration were submitted to EPA

[[Page 69212]]

by the Alliance of Automobile Manufacturers, the General Electric Company, and the Prince William Sound Regional Citizen's Advisory Council (RCAC). Petitions for judicial review were filed by the American Chemical Council, the Coke Oven Environmental Task Force, the General Electric Company, and Mr. Stan Stephens. On April 5, 2004, the court consolidated the petitions for review under Stan Stephens v. USEPA, No. 04-1112 (DC Cir.). On April 30, 2004, the court granted the motion of Alyeska Pipeline Service Company to intervene in the case and granted the parties' joint motion to hold the case in abeyance pending EPA's response to the petitions for reconsideration.

In responding to the petitions, EPA plans to publish two separate rulemakings. Today's proposed amendments are the first of these two actions. The proposed amendments in this notice are those that the Agency can make without substantial analysis of data and can be made more quickly to ensure correct implementation of the final rule. The remaining items, which are associated with the incorporation of wastewater into the OLD NESHAP, will be addressed in the second rulemaking. Today's proposed amendments, therefore, are not to be considered EPA's response to all of the issues raised in the petitions.
Proposed Amendments to the Organic Liquids Distribution NESHAP

We are proposing a number of changes to the OLD NESHAP. For storage tanks, the proposed changes include, but are not limited to, control options for those storing high vapor pressure liquids and overlap with other storage tank rules. For transfer racks, the proposed changes include, but are not limited to, defining total actual annual facility- level organic liquid loading volume and how to calculate its value, revising the definition of transfer rack, and compliance dates and control options as the result of changes in facility-level loading volumes. Numerous changes are being proposed with regard to notification, recordkeeping, and reporting requirements including, but not limited to: (1) Requirements for emission sources that are not required to be controlled under the OLD NESHAP, including startup, shutdown, and malfunction plans; (2) operating scenarios; (3) initial notification of compliance status (NOCS); and (4) Department of Transportation (DOT) certification records for transport vehicles. Other proposed changes include, but are not limited to, adding vapor balancing as a control option for containers, clarifying that cargo tank work practice standards only apply to tanks equipped with vapor collection equipment, allowing an alternative ASTM International method to Method 18 (40 CFR part 60, Appendix A), four new definitions and cross-referencing of definitions to other regulations, and removing the ``1-hour'' requirement for offsite records. In addition, today's proposed amendments would correct typographical errors, including incorrect cross-references.
1. How Are Definitions Being Revised?
  1. Total Actual Annual Facility-Level Organic Liquid Loading Volume. One of the criteria for determining whether a transfer rack is to be controlled or not is the annual loading volume of organic liquids at the facility. Absent from the OLD NESHAP are a definition of ``total actual annual facility-level organic liquid loading volume'' and guidance on how to calculate this value. Therefore, we are proposing to add a definition to the final rule and include in the definition a detailed explanation of how to calculate this value for existing facilities and for new facilities.
    
    In proposing this definition, we note two important items. First, the loading volume considers both transfers made between facilities (for transport out of the facility) and transfers made within a facility (for transport within the facility). This clarifies the intent to consider both types of transfers and corrects an error in items 7 through 10 in Table 2 to 40 CFR part 63, subpart EEEE, when the phrase ``out of the facility'' is used. Second, we are proposing to calculate this value as an average over 3 years of annual loading volumes rather than a single annual value. Allowing a facility to average its loading volume over 3 years is reasonable because this would smooth out fluctuations in loading volumes from year to year that might arise due to temporary situations, thereby eliminating different control requirement outcomes caused by temporary changes below or above the throughput cut-off level that would occur with an annual time period. The proposed 3-year average should also allow facilities sufficient lead time in tracking their loading volume to assess the need for controlling transfer racks should the loading volume exceed the criterion's trigger value.
    
    We are proposing the methodology to be used to calculate this value as an average using 3 years of actual loading volume data. The value would be recalculated once per year. For example, a facility would collect loading volume data for years 1, 2, and 3. At the end of year 3, the three annual values would be averaged to calculate the total actual annual facility-level organic liquid loading volume. This value would represent the loading volume used in determining whether the transfer racks at the facility would need to be controlled. At the end of year 4, the facility would calculate the annual average using the loading volume data for years 2, 3, and 4. This pattern would repeat itself each year.
    
    For existing affected sources, we are proposing that this calculation be made on a calendar year basis, starting January 1, 2004. If an existing affected source does not have actual loading volume data for the time period from January 1, 2004, through February 2, 2004, (the time period before the effective date of the OLD NESHAP), the owner or operator would calculate loading volume for that period based on the average loading volume from February 3, 2004, through December 31, 2004.
    
    For new affected sources, we are proposing the option of making this calculation beginning on the actual startup date of the facility or on the first day of the calendar month following the month in which actual startup occurs. For example, if actual startup is March 13, 2005, the facility has the option of either using March 13 to March 12 as its annual basis or April 1 to March 31 as its annual basis. We are also proposing that once owners or operators select the beginning date to start their calculations, no changes can be made thereafter.
    
    New affected sources are required to be in compliance at startup. In order for a new affected source to be in compliance, the owner or operator must make a determination as to which transfer racks need to be controlled. However, new affected sources will not have actual loading volume data at their startup to make this determination. Therefore, we are proposing that new facilities make projections as to the facility-level loading volume for the first 3 years of operation. Based on this forecast, the owner or operator would determine the total actual annual facility-level organic liquid loading volume and use the result to determine which transfer racks need to be controlled at startup.
    
    At the end of the first year following the date selected to begin the calculation, the owner or operator would calculate the 3-year average using the first year's actual loading volume plus a new forecast of the loading volume for the next 2 years. At the end of the second year, the owner or
    
    [[Page 69213]]
    
    operator would calculate its 3-year average using the first 2 years' actual loading volume data plus a new forecast of loading for the next year. At the end of the third year, and for all subsequent years, following startup, the owner or operator would have actual loading volume data for 3 years and would no longer need to forecast loading volumes. The owner or operator would use the actual loading volume data for the first 3 years to make this calculation, and then use the ``rolling'' 3 years of data for future calculations, as would owners and operators of existing affected sources.
  2. Transfer Rack. In the OLD NESHAP, the definition of transfer rack includes the concept of loading of organic liquids into transport vehicles. Unfortunately, there were two shortcomings with the definition.
    
    First, the definition is inconsistent with how the term is used when describing the affected sources. As stated in the OLD NESHAP, 40 CFR part 63, subpart EEEE applies to (emphasis added): ``transfer racks at which organic liquids are loaded into or unloaded out of transport vehicles and/or containers'' (see 40 CFR 63.2338(b)(2)) and ``all transport vehicles while they are loading or unloading organic liquids at transfer racks'' (see 40 CFR 63.2338(b)(4)). However, in the definition section of the OLD NESHAP, transfer rack is defined in part (emphasis added) as ``a single system used to load organic liquids into transport vehicles.'' The definition of transfer rack, by limiting itself to only the loading of liquids, creates an inconsistency with the use of the term when defining the affected source. In the affected source, transfer racks can be loading or unloading organic liquids (emphasis added).
    
    The intent of the rule is that, for purposes of defining the affected source, both loading and unloading racks are to be included. For purposes of control requirements, however, the OLD NESHAP apply only to racks when they are loading organic liquids into transport vehicles or, for new sources only, containers.
    
    To accomplish this intent, we are proposing to modify the definition of ``transfer rack'' to also refer to unloading. Because of this proposed change to the definition of transfer rack, we are also proposing numerous language changes to ensure that the rule language is specific that control is required for transfer racks when they are loading organic liquids into cargo tanks or when they are filling containers.
    
    For new sources, transfer racks may also load containers, which the definition failed to mention. Therefore, we are proposing to add containers to the definition of transfer rack.
  3. Cross Reference to Other Rules. The OLD NESHAP use several terms that are defined in other subparts, but not directly in the OLD NESHAP. We are proposing to revise the introductory paragraph at 40 CFR 63.2406 to cross-reference the other 40 CFR part 63 subparts that are referenced in the OLD NESHAP. This is being done by citing the specific definition sections of the applicable subparts in the same manner we cited the definitions found in 40 CFR 63.2 of the General Provisions. This change would not make the OLD NESHAP any more or less stringent, but simply clarifies the intent to use those definitions in the other subparts as appropriate and necessary to implement the OLD NESHAP.
    
    We are proposing to add four new definitions--bottoms receivers, surge control vessels, low-throughput transfer racks, and high- throughput transfer racks--to the OLD NESHAP. These terms are added because their definitions in the cross-referenced rules do not apply to the OLD NESHAP and, therefore, needed to be added.
    
    We are proposing to add a sentence to the introductory paragraph of 40 CFR 63.2406 to clarify a potential conflict in priority between the OLD NESHAP (subpart EEEE) and 40 CFR part 63, subpart PP. The introductory language in the OLD NESHAP and in subpart PP both claim that the terms as defined within each subpart shall have precedent over any other definition for those same terms in another subpart. We are proposing to amend the language in the OLD NESHAP to specifically override the language in subpart PP such that the terms ``container'' and ``safety device'' shall have the meaning given them in the OLD NESHAP notwithstanding the introductory language in 40 CFR 63.921.
    
    We do not believe any other changes to the definition section of the OLD rule are necessary. When complying with the OLD NESHAP, an owner or operator may be required to comply with another subpart (e.g., with 40 CFR part 63, subpart UU, for equipment leak components). If a term needs to be defined in order to comply with subpart UU and that term is not defined in the OLD NESHAP, then the owner or operator would use the definition found in subpart UU. In summary, when complying with the OLD NESHAP, if a term is used and it is not defined in the OLD NESHAP, then that term has the meaning assigned it in the 40 CFR part 63 subpart that is being complied with.
  4. Startup and Shutdown. In 40 CFR 63.2406, we are proposing to clarify the definitions of ``startup'' and ``shutdown'' by adding the phrase ``(other than as part of normal operation for a batch-type operation), including equipment'' after ``or portion thereof.''
    
    The proposed wording for ``shutdown'' would now read: ``Shutdown means the cessation of operation of an OLD affected source, or portion thereof (other than as part of normal operation of a batch-type operation), including equipment required or used to comply with this subpart, or the emptying and degassing of a storage tank. Shutdown as defined here includes, but is not limited to, events that result from periodic maintenance, replacement of equipment, or repair.''
    
    The proposed wording for ``startup'' would now read: ``Startup means the setting in operation of an OLD affected source, or portion thereof (other than as part of normal operation of a batch-type operation), for any purpose. Startup also includes the placing in operation of any individual piece of equipment required or used to comply with this subpart including, but not limited to, control devices and monitors.''
    
    The normal operation of transfer racks is such that at times a transfer rack is transferring liquids and at other times it is not transferring liquids. We received questions about whether instances in which transfer racks begin or cease transferring liquids as part of normal ``batch'' type operations would constitute ``startup'' or ``shutdown'' episodes. We never intended such instances to be interpreted in this way. Therefore, to avoid misunderstandings, we are proposing to revise the definitions of startup and shutdown to make it clear that the commencement or cessation of actual transfer of liquids through a transfer rack as part of batch-type operations does not constitute a ``startup'' or a ``shutdown'' of the transfer rack within the meaning of the OLD NESHAP. As a result of this proposed change, emission sources (i.e., transfer racks) that are subject to the OLD NESHAP, but for which control is not required, would not be required to minimize emissions during such periods as would be required under the General Provisions (i.e., 40 CFR 63.11(e)(1)) and would not be required to be addressed in a facility's startup, shutdown, and malfunction plan (i.e., 40 CFR 63.11(e)(3)). Likewise, emission sources subject to the OLD NESHAP for which control is required would remain subject to the control requirements during routine commencement or
    
    [[Page 69214]]
    
    cessation of operations that are part of normal batch-type operations.
    
    These proposed changes would also make the OLD NESHAP consistent with other recent EPA standards that recognize cessation of operations that is part of the normal characteristics of batch operations and batch-type operations is not considered ``startup'' or ``shutdown'' for purposes of startup, shutdown, and malfunction plans. Rather than revising the definitions of ``startup'' and ``shutdown'' to achieve this purpose, an alternative may be to simply amend Table 12 to 40 CFR part 63, subpart EEEE, to clarify that the duty to minimize emissions during periods of startup, shutdown and malfunction, in 40 CFR 63.11(e)(1) of the General Provisions, does not apply to emissions sources that are part of the OLD affected source but are not subject to emissions control requirements. EPA requests comment on this alternative approach.
  5. Vapor Balancing System. We are proposing revisions to this definition to include reference to containers. We are proposing to extend the option of vapor balancing systems to containers. We are also proposing to clarify that vapors need to be ``directly conveyed'' to a ``chemical manufacturing process unit,'' and are, thus, proposing to replace ``compresses the vapors for feeding into a chemical process manufacturing unit'' with ``compresses the vapor for direct conveyance to a chemical manufacturing unit.''
  6. Vapor Collection System. We are proposing to add reference to the conveyance of vapors displaced during the loading of containers to this definition. The OLD NESHAP inadvertently do not contain this reference, even though the use of control devices to control emissions from the filling of containers is a control option.
2. How Are Control Options Being Revised?
  1. Storage Tanks with High Vapor Pressure Liquids. Between proposal and promulgation, we added the equivalent control option of routing emissions to a fuel gas system or back to a process, per 40 CFR part 63, subpart SS, for storage tanks storing liquids with vapor pressures less than 11.1 psia. The OLD NESHAP did not extend this option to storage tanks storing liquids with vapor pressures greater than 11.1 psia. This was not an intentional exclusion. Most, but not all, tanks storing liquids with high vapor pressure are pressurized. Pressurized tanks do not have emissions. However, non-pressurized tanks storing liquids with high vapor pressures have the same types of emissions (working and/or breathing losses) as those tanks storing liquids with lower vapor pressures. In these instances, the controls that are applicable to the tanks storing the liquids with vapor pressures less than 11.1 psia are applicable to tanks storing liquids with vapor pressures greater than 11.1 psia. Therefore, we are proposing revisions, which appear in Tables 2 and Table 4 to 40 CFR part 63, subpart EEEE, to allow these storage tanks the same equivalent option as those storing lower vapor pressure liquids.
  2. Overlap of Storage Tank Rules. The Agency is proposing to revise the manner in which the OLD NESHAP address the overlap of the OLD NESHAP with 40 CFR part 60, subpart Kb (Standards of Performance for Volatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced After July 23, 1984) and with 40 CFR part 61, subpart Y (National Emission Standard for Benzene Emissions from Benzene Storage Vessels). In the OLD NESHAP, 40 CFR 63.2396(a), storage tanks that are subject to the OLD NESHAP requirements (which reference 40 CFR part 63, subpart WW) and either of these other two rules are required to comply with the requirements of the OLD NESHAP when the tank is in OLD operation.
    
    Another recent rule (i.e., the Miscellaneous Organic NESHAP, or MON) promulgated by the Agency handles this overlap in a different fashion. In the MON, we allow facilities with storage tanks subject to both the MON and either of the other two rules noted above to be considered in compliance with the MON when they are in compliance with either of the other two rules.
    
    In assessing whether this approach was appropriate for the OLD NESHAP, we reviewed the OLD data used to establish the MACT floor and compared the requirements of the OLD NESHAP with 40 CFR part 60, subpart Kb, and 40 CFR part 61, subpart Y. Based on that review, 40 CFR part 60, subpart Kb, is equal to or more stringent than the MACT floor established for storage tanks. Therefore, allowing a facility to comply with 40 CFR part 60, subpart Kb, or, for that matter, with 40 CFR part 61, subpart Y, would not be less stringent than the MACT floor for the OLD NESHAP and provides the same level of control as that found in 40 CFR part 63, subpart WW. We, therefore, are proposing to revise the wording in 40 CFR 63.2396(a) to allow facilities to comply with 40 CFR part 60, subpart Kb, or 40 CFR part 61, subpart Y, for these storage tanks. However, we are not proposing to revise the 5-year recordkeeping requirement for OLD storage tanks. This is a longer timeframe than found in 40 CFR part 60, subpart Kb, or in 40 CFR part 61, subpart Y, which have a 2-year timeframe for keeping records. Finally, we are not proposing to revise the OLD monitoring, recordkeeping, and reporting requirements for OLD storage tanks that are controlled using closed vent systems (which is consistent with the MON). In sum, we have determined that the MACT floor is being maintained, and there is no loss in stringency as the result of the proposed changes.
  3. Transfer Racks. While we believe our intent is clear in 40 CFR 63.2346(b) as to which transfer racks are to be controlled, the language is not accurate. The organic hazardous air pollutant (HAP) criterion is applied to the individual rack, but the ``facility-level organic liquid loading volume'' criterion is not. The loading volume criterion is based on the volume for all transfer racks and not for the individual transfer rack. Therefore, we are proposing to revise the introductory text as follows:
    
    ``For each transfer rack that is part of the collection of transfer racks that meets the total actual annual facility-level organic liquid loading volume criterion for control in Table 2 to this subpart, items 7 through 10, you must comply with paragraph (b)(1), (2), or (3) of this section for each arm in the transfer rack loading an organic liquid whose organic HAP content meets the organic HAP criterion for control in Table 2 to this subpart, items 7 through 10.''
  4. Changes in OLD Loading Volume. Over time, the OLD loading volume at a facility may increase or decrease. These changes may be large enough that the 3-year rolling average creates a situation where a facility that is controlling its transfer racks no longer meets the criteria for control, or where a facility that is not controlling its transfer racks now meets the criteria for control. The OLD NESHAP does not explicitly indicate the control requirements when a facility encounters such situations. We are, therefore, proposing language to specifically indicate the control requirements and timing when such changes occur.
    
    We are proposing that if a facility is controlling its transfer racks, but the loading volume decreases at a later date to such a level that the criteria for control are no longer being met, compliance with the control requirements specified in 40 CFR 63.2386(b)(1), (2), or (3) is no longer required until such time that the total
    
    [[Page 69215]]
    
    actual facility-wide organic loading volume increases to a level requiring control.
    
    We are also proposing that if a facility is not controlling its transfer racks, but the loading volume increases at a later date to such a level that the criteria for control is now met, compliance with the control requirements specified in 40 CFR 63.2386(b)(1), (2), or (3) is required immediately, except as may be provided for existing sources only.
  5. Transfer Racks and Table 2 Emission Limits. The OLD NESHAP require a transfer rack to comply with each of the three emission limitations identified in item 7 in Table 2 to 40 CFR part 63, subpart EEEE. These emission limitations are: (1) Reduce emissions by 98 percent reduction or to 20 ppmv; (2) vent emissions through a closed vent system to any combination of control devices in compliance with 40 CFR part 63, subpart SS; and (3) meet one of two work practice standards specified in Table 4 to subpart EEEE. Requiring a facility to comply with all three emission limitations was not our intent and further is not technically feasible. To correct this, we are proposing to combine the first two emission limitations into a single emission limitation (which we incorrectly split into two limitations between proposal and promulgation and which would now parallel the correct construct of item 6 in Table 2 to subpart EEEE) and clarify that a facility is to comply with either 98 percent reduction or 20 ppmv emission limitation or one of the two work practice standards.
  6. Transfer Racks and Routing Emissions to a Process. The OLD NESHAP allow a facility the option to comply with 40 CFR part 63, subpart SS, which allows a facility to route emissions to fuel gas systems or back to a process (emphasis added). The OLD NESHAP inadvertently use the phrase ``the process,'' which has the potential effect of unnecessarily limiting a facility's option for routing vent gases. Therefore, we are proposing to use the phrase ``a process'' in conjunction with this compliance option.
  7. Vapor balancing and containers. The OLD NESHAP do not allow vapor balancing as a control option for the filling of containers. However, vapor balancing can be an effective control option for the filling of containers. Therefore, we are proposing vapor balancing, under certain conditions, as a control option for the filling of containers, identifying applicability for existing sources and new sources and revising the definitions of ``vapor balancing systems'' and ``vapor collection system.''
  8. Vapor balancing and routing of displaced vapors. The control option of vapor balancing for transfer racks is stated inconsistently in the OLD NESHAP in 40 CFR 63.2346(b)(3) and in Table 7 to 40 CFR part 63, subpart EEEE. We are proposing to resolve this inconsistency by revising 40 CFR 63.2346(b)(3) to include routing of vapors to a process unit.
    
    The OLD NESHAP direct that the routing of the displaced vapors is to be made to the ``appropriate storage tank.'' We are proposing to revise this phrase to now read ``to the storage tank from which the liquid being loaded originated.'' We believe this change makes the rule clearer.
  9. Cargo Tank Work Practice Standards. The cargo tank work practices in the OLD NESHAP (see 40 CFR 63.2346(d) and items 4 and 5 in Table 4 to 40 CFR part 63, subpart EEEE) create a technological inconsistency--requiring vapor tightness on transport vehicles being loaded at transfer racks that were not being controlled. We are proposing to correct this error by requiring vapor tightness only on transport vehicles being loaded at transfer racks that are being controlled. The proposed amendment would affect both cargo tanks with and cargo tanks without vapor collection equipment.
3. How Are My Notification, Recordkeeping, and Reporting Requirements Being Revised?
  1. Emission sources not subject to control. We are proposing to overhaul the OLD NESHAP notification, recordkeeping, and reporting requirements for emission sources not subject to control. The proposed amendments are found mostly in a proposed new section, 40 CFR 63.2343, with some additional changes needed in other parts of the rule. The OLD NESHAP currently identifies requirements for these sources in 40 CFR 63.2346(h) and 63.2386(c)(9). Under today's proposed amendments, 40 CFR 63.2346(h) would be deleted and ``reserved,'' because it is no longer needed. With regard to 40 CFR 63.2386(c)(9), the proposed amendments would revise (as described below) and redesignate the paragraph (as proposed 40 CFR 63.2386(c)(10)(i)).
    
    In today's proposed rulemaking, we are proposing to exempt all emission sources in the affected source not requiring control under the OLD NESHAP from notification, recordkeeping, and reporting requirements, except as otherwise specified in the proposed new 40 CFR 63.2343. The proposed exceptions would apply to storage tanks and transfer racks.
    
    Storage tanks and transfer rack that would never be required to be controlled. For storage tanks and transfer racks that would never be required to be controlled under the OLD NESHAP as they currently apply, we are proposing that owners and operators submit an Initial Notification identifying such emission sources; and keep documentation verifying the ``no control'' status be kept up-to-date by the owner or operator. By the phrase ``up-to-date,'' we mean that such emission sources at a facility are identified in the documentation regardless of when the documentation was last compiled. Further, this documentation needs to be up-to-date only as it pertains to emission sources that are still physically present at a facility.
    
    The proposed amendments would also have the effect of eliminating the requirement for listing these sources in the NOCS, first compliance report, and subsequent compliance reports. Once the Initial Notification has been submitted, we believe it is unnecessary to continue to identify such emission sources in NOCS, first compliance report, and subsequent compliance reports as long as owners and operators keep documentation that such emission sources would never require control under the OLD NESHAP.
    
    Storage tanks and transfer racks that could be required to be controlled, but for which control is not currently required. For storage tanks and transfer racks that could be required to be controlled, but for which control is not currently required, we are proposing changes to notification and reporting and to documentation.
    
    We believe that it is important for an owner or operator to identify those storage tanks and transfer racks for which control could be required if and when the HAP content or throughput changes, even if control is not required at the time either the NOCS of the first compliance report is filed. Therefore, we are proposing owners and operators submit a list of all transfer racks (except those at which only unloading of organic liquids occurs) and of tanks greater than or equal to 18.9 cubic meters (5,000 gallons) that are part of the affected source but are not subject to any of the emission limitations, operating limits, or work practice standards of 40 CFR part 63, subpart EEEE (see proposed 40 CFR 63.2386(c)(10)(i)).
    
    Owners and operators would be required to submit this list with either the NOCS or the first Compliance report, whichever is submitted first.
    
    [[Page 69216]]
    
    After the NOCS or a Compliance report has been submitted, changes to a storage tank or transfer rack may have been made that affect its compliance status (e.g., an uncontrolled storage tank becomes subject to control). The types of changes that we are proposing to be reported are:
    
    Any storage tank or transfer rack that became subject to control since the filing of the last Compliance report (see proposed 40 CFR 63.2386(d)(3)). The intent here is to cover any storage tank or transfer rack that existed at the facility when the last Compliance report was filed, but has undergone a change that now subjects the storage tank or transfer rack to control; and any storage tank or transfer rack that was constructed at the facility since the last Compliance report was filed, that is being used (e.g., contains liquid), that is in OLD service and that meets the OLD criteria for control.
    
    Any storage tank greater than or equal to 18.9 cubic meters (5,000 gallons) and any transfer rack that is part of the affected source, but which are not subject to any of the emission limitations, operating limits, or work practice standards of the OLD NESHAP, that became part of the affected source since the filing of the NOCS or the last Compliance report (see proposed 40 CFR 63.2386(d)(4)). The intent here is to cover any storage tank or transfer rack that was constructed at the facility since the NOCS or the last Compliance report was filed, that is part of the affected source (i.e., is in OLD service), but does not meet any of the criteria for control under the OLD rule; and any storage tank or transfer rack that existed at the facility prior to the filing of the NOCS or last Compliance report that was not in OLD service that is now in OLD service (i.e., is now part of the affected source), but does not meet any of the criteria for control under the OLD NESHAP.
    
    We are proposing that such changes be reported in either the NOCS or the first Compliance report (depending on which was submitted first (see proposed 40 CFR 63.2382(d)(2)(viii) and 63.2386(c)(10(ii)) and in subsequent Compliance reports whenever such changes occur after the filing of the last Compliance report (see proposed 40 CFR 63.2386(d)(3) and (4)).
    
    Proposed 40 CFR 63.2343 specifies the documentation that would be required for these emission sources. We are also proposing to modify 40 CFR 63.2390, What records must I keep?, to clarify the applicability of proposed 40 CFR 63.2343 and 40 CFR 63.2390 to all emission sources subject to the OLD NESHAP.
    
    For storage tanks that could be subject to control, but are not required to be controlled, we are proposing that documentation be kept that demonstrates the status of the tank, including a record of the annual average true vapor pressure of the organic liquid being stored in each such tank.
    
    For transfer racks that could be subject to control, but are not required to be controlled, we are proposing that documentation be kept that demonstrates the status of the transfer rack.
    
    General Provisions. For all emission sources for which control is not required, we are proposing to amend the applicability of the General Provisions in two ways. First, we are proposing to modify the applicability of 40 CFR 63.6(e)(3) by not requiring startup, shutdown, and malfunction (SSM) plans for these emission sources because SSM plans apply to control devices used to comply with regulations, and these emission sources are not required to be controlled.
    
    Second, in the proposed new 40 CFR 63.2343 for emission sources not required to be controlled, we specifically identify those changes that require a facility to submit information and are proposing to modify the applicability of 40 CFR 63.9(j) such that it would not apply to these emission sources.
  2. Transport Vehicles and DOT Certifications. In the OLD NESHAP, we require owners or operators to keep documentation on the DOT certifications for transport vehicles loaded at their facilities. Other NESHAP allow an alternative to this requirement, which we believe can also be applied to transport vehicles loading organic liquids. This proposed alternative would allow owners and operators to simply record in a number of acceptable methods the verification of DOT certification without actually keeping such documentation (see proposed 40 CFR 63.2390(c)(3)).
  3. Initial Notification of Compliance Status. The OLD NESHAP allow facilities with multiple control devices to submit a single NOCS and up to 240 days after the compliance date to submit it. To make this provision explicitly clear, we are proposing to revise the applicability of the General Provisions at 40 CFR 63.7(g) and 63.9(h)(1)-(6) in Table 12 to 40 CFR part 63, subpart EEEE, to allow facilities to submit a single initial NOCS with test reports either within 240 days after the compliance date or within 60 days after the completion of the last compliance test demonstrating compliance, whichever occurs first.
  4. Offsite Records. The OLD NESHAP (see 40 CFR 63.2394(a)) allow facilities to store on-site records ``in electric form at a separate location from the site provided they can be access and printed at the site within 1 hour after a request by the applicable title V permitting authority.'' EPA included the ``1-hour'' requirement at promulgation, but now believes that it is unnecessarily restrictive. Therefore, we are proposing to revise 40 CFR 63.2394(a) by removing the ``1-hour'' requirement and stating explicitly that records kept off-site are to be available for ``expeditious review and inspection.'' We are also proposing to eliminate the provision allowing on-site records to be stored off-site in electronic format because ``expeditious retrieval'' of records stored off-site does not meet the General Provision's requirements that records be stored ``on-site'' for the first 2 years.
  5. Operating Scenarios. The OLD NESHAP require facilities to identify operating scenarios in the NOCS report and then to update changes to operating scenarios in the semiannual compliance reports. We are proposing to delete ``operating scenarios'' from the OLD NESHAP because the term is not applicable to the OLD source category.
4. How Are Compliance Requirements Being Changed?
  1. Changes in OLD Loading Volume--Compliance Dates. We are proposing language to clarify when transfer racks must be in compliance when the total actual annual facility-level organic liquid loading volume decreases such that control is no longer required, or when it increases such that control is required (see 40 CFR 63.2342(a)(3) and (b)(3)). For both new and existing sources, we are proposing that a source whose loading volume increases to a level such that control of transfer racks is required, be in compliance with the transfer rack requirements immediately. We are proposing to define ``immediately'' as the first day of the period following the end of the 3-year period triggering the control criteria.
    
    For existing sources, however, we are proposing that owners or operators of existing sources be allowed to request a compliance extension of up to 1 year if the additional time is necessary for the installation of controls. This proposed request for a compliance extension is similar to that provided for under 40 CFR 63.100(l)(4)(ii)(B) of the Hazardous Organic NESHAP. We are also proposing to limit the use of this compliance extension provision to once for each facility (see 40 CFR 63.2342(b)(3)(ii)(I)). That is, once an owner or operator has requested an
    
    [[Page 69217]]
    
    extension of compliance for its facility, the owner or operator cannot request such an extension at a later date if changes in loading volume again create a situation in which control of transfer racks is once again required.
  2. ASTM D7420-99. In the preamble to the OLD NESHAP, we indicated that we had included ASTM D7420-99, Standard Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass Spectrometry (GC/MS), as an alternative to Method 18. However, we neglected to add the method to the final rule. Therefore, we are proposing language, in 40 CFR 63.2354(b)(3), adding ASTM D7420-99 as an alternative to Method 18 to determine compliance with the organic HAP or TOC emission limit.
  3. Reformulation. One of the petitioners requested clarification as to the periodic reporting requirements for a facility that reformulates materials prior to the compliance date, and for a facility that reformulates materials after the compliance date. The reformulation the petitioner is concerned about is where a material that meets the definition of an organic liquid as defined in 40 CFR 63.2402 is reformulated in such a manner that the material no longer meets the definition of an organic liquid.
    
    The OLD NESHAP apply to emission sources when they are in OLD service. If a facility reformulates a material in such a manner that the material no longer is an organic liquid, as defined in 40 CFR 63.2406, the emission source is not in OLD service and, therefore, is neither subject to the OLD NESHAP nor its reporting requirements. If all of the material at a facility were reformulated such that there is no organic liquid at the facility, the entire facility would have no emission sources in organic liquid service and would not be required to meet the periodic compliance reporting requirements. If the facility were to later reformulate the material such that it once again met the definition of organic liquid, then the emission source would be in OLD service and subject to all applicable requirements of the OLD NESHAP, including periodic reporting requirements.
    
    The Agency does not believe that it is necessary to modify the OLD NESHAP to address the specific situations posed by the petitioner. In addition, we do not believe this issue needs to be treated differently if the reformulation occurs prior to or after the compliance date of the final rule.
5. How Is the Affected Source Being Changed?
  1. Containers. In 40 CFR 63.2338(b)(2) of the OLD NESHAP, we identify ``transfer racks'' as a component of the affected source and identify in that paragraph both ``transport vehicles'' and ``containers'' into which or out of which the liquids are loaded. We then identify, in 40 CFR 63.2338(b)(4), ``transport vehicles'' as a separate component of the affected source. However, we neglected to also identify ``containers'' as a separate component of the affected source. To correct this oversight, we are proposing to add a new paragraph (b)(5) to 40 CFR 63.2338 to identify containers as a separate component of the affected source.
  2. Transport Vehicles. In 40 CFR 63.2338(b)(4) of the OLD NESHAP, it is unclear as to whether the affected source includes transport vehicles while they are loading or unloading organic liquids at any transfer rack or only at transfer racks subject to the OLD NESHAP. We are proposing to revise 40 CFR 63.2338(b)(4) to state that only those transport vehicles loading or unloading at transfer racks subject to the OLD NESHAP are to be included in the affected source.
  3. Excluded Equipment. As stated in 40 CFR 63.2338(b), the affected source is composed of storage tanks, transfer racks, equipment leak components, transport vehicles, and containers. The OLD NESHAP, in 40 CFR 63.2338(c), exclude from the affected source three of these five types of equipment--storage tanks, transfer racks, and equipment leak components--under certain conditions (e.g., subject to another 40 CFR part 63 NESHAP, used in special operations, used to conduct maintenance activities). We know of no reason that transport vehicles and containers when used in the same circumstances as the three cited types of equipment should not also be included in these exclusions. Therefore, we are proposing to revise 40 CFR 63.2338(c) accordingly.
  4. Equipment Leak Components. The OLD NESHAP (see 40 CFR 63.2338(c)(2)) is unclear as to which equipment leak components are to be excluded from the affected source definition. For example, are equipment leak components associated with a pipeline originating offsite that goes directly to a tank subject to the Hazardous Organic NESHAP (HON) part of the affected source? Or, as another example, are equipment leak components associated with a pipeline from a transfer rack subject to the OLD NESHAP that goes to a tank subject to the HON part of the affected source?
    
    To clarify the determination of which equipment leak components are included in the definition of the affected source and which are excluded, we are proposing to revise 40 CFR 63.2338(b)(3) to clearly state that equipment leak components are part of the affected source if they are associated with pipelines that transfer organic liquids directly to and from storage tanks and/or transfer racks, both of which are subject to the OLD NESHAP. Equipment leak components associated with pipelines that connect two storage tanks, two transfer racks, or a storage tank and a transfer rack are subject to the OLD NESHAP only if both storage tanks, both transfer racks, or both the storage tank and transfer rack are subject to the OLD NESHAP. These three scenarios comprise the situations in which equipment leak components associated with pipelines are part of the OLD affected sources.
    
    Lastly, because the proposed revisions to 40 CFR 63.2338(b)(3) include all those equipment leak components that we intend to include, we do not believe there is any need to have an equipment leak component exclusion. Therefore, we are proposing to delete 40 CFR 63.2338(c)(2) from the OLD NESHAP.
  5. Coke by-product Plants. One of the petitioners requested clarification as to the applicability of the OLD NESHAP to coke by- product plants. On January 30, 2001 (66 FR 8220), EPA deleted coke by- product plants from the list of major and area sources of HAP required by CAA section 112(c)(1). Consequently, 40 CFR part 63 MACT standards promulgated under CAA section 112(d), such as the OLD NESHAP, would not apply to the deleted coke by-product plant source category. Moreover, as EPA explained in 2001, coke by-product plants remain subject to the pre-existing NESHAP for benzene emissions from coke by-product recovery plants at 40 CFR part 61, subpart L. See 66 FR at 8222. EPA is not proposing any changes to the OLD NESHAP in order to clarify this issue, as it is unnecessary to do so. The result follows from EPA's previous action in 2001 deleting the coke by-product plant source category.
6. Miscellaneous Edits
  
  There are numerous edits being proposed to address typographical errors and oversights in the OLD NESHAP. These edits make clearer our intent, correct punctuation, or change cross-references because of the other changes being proposed in today's rulemaking; they do not affect the stringency of the final rule or its
  
  [[Page 69218]]
  
  enforceability. These edits may be found in the EDOCKET (see ADDRESSES section).
Statutory and Executive Order Reviews
1. Executive Order 12866: Regulatory Planning and Review
  
  Under Executive Order 12866 (58 FR 5173, October 4, 1993), the EPA must determine whether the regulatory action is ``significant'' and, therefore, subject to Office of Management and Budget (OMB) review and the requirements of the Executive Order. The Executive Order defines ``significant regulatory action'' as one that is likely to result in standards that may:
  
  (1) Have an annual effect on the economy of $100 million or more or adversely affect, in a material way, the economy, a sector of the economy, productivity, competition, jobs, the environment, public health or safety, or State, local, or tribal governments or communities;
  
  (2) create a serious inconsistency or otherwise interfere with an action taken or planned by another agency;
  
  (3) materially alter the budgetary impact of entitlement, grants, user fees, or loan programs or the rights and obligations of recipients thereof; or
  
  (4) raise novel legal or policy issues arising out of legal mandates, the President's priorities, or the principles set forth in the Executive Order.
  
  Pursuant to the terms of Executive Order 12866, OMB has notified EPA that it considers this a ``non-significant regulatory action'' within the meaning of the Executive Order and is therefore not subject to OMB review.
2. Paperwork Reduction Act
  
  This action does not impose any new information collection burden. The final rule required owners and operators to list sources not subject to control in the first and subsequent compliance reports and to keep appropriate documentation. The final rule applied these requirements across-the-board for all emission sources not requiring control and, in general, was not specific as to what recordkeeping is required. Under the proposed amendments, we are clarifying how these provisions would apply to those emission sources for which control would never be required and to those emission sources for which control could be required, but is not currently required. In addition, we are identifying the specific circumstances under which listing in subsequent Compliance reports would be required for sources for which control is not required rather than requiring all previously identified sources to be re-listed. Further, we are narrowing the applicability of certain sections of the General Provisions for sources for which control is not required because the proposed amendments make such application of those sections in the General Provisions unnecessary. Thus, in sum, the proposed amendments are not adding new information collection burden. However, the Office of Management and Budget (OMB) has previously approved the information collection requirements contained in the existing regulations at 40 CFR part 63, subpart EEEE under the provisions of the Paperwork Reduction Act, 44 U.S.C. 3501 et seq. and has assigned OMB control number 2060 0539, EPA ICR number 1963. A copy of the OMB approved Information Collection Request (ICR) may be obtained from Susan Auby, Collection Strategies Division; U.S. Environmental Protection Agency (2822T); 1200 Pennsylvania Ave., NW., Washington, DC 20460 or by calling (202) 566-1672.
  
  Burden means the total time, effort, or financial resources expended by persons to generate, maintain, retain, or disclose or provide information to or for a Federal agency. This includes the time needed to review instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting, validating, and verifying information, processing and maintaining information, and disclosing and providing information; adjust the existing ways to comply with any previously applicable instructions and requirements; train personnel to be able to respond to a collection of information; search data sources; complete and review the collection of information; and transmit or otherwise disclose the information.
  
  An agency may not conduct or sponsor, and a person is not required to respond to a collection of information unless it displays a currently valid OMB control number. The OMB control numbers for EPA's regulations in 40 CFR are listed in 40 CFR part 9.
3. Regulatory Flexibility Act
  
  The Regulatory Flexibility Act (RFA) generally requires an agency to prepare a regulatory flexibility analysis of any rule subject to notice and comment rulemaking requirements under the Administrative Procedure Act or any other statute unless the agency certifies that the rule will not have a significant economic impact on a substantial number of small entities. Small entities include small businesses, small organizations, and small governmental jurisdictions.
  
  For purposes of assessing the impacts of today's proposed amendments on small entities, small entity is defined as: (1) A small business as defined by the Small Business Administration's (SBA) regulations at 13 CFR 121.20; (2) a small governmental jurisdiction that is a government of a city, county, town, school district or special district with a population of less than 50,000; and (3) a small organization that is any not-for-profit enterprise which is independently owned and operated and is not dominant in its field.
  
  After considering the economic impacts of today's proposed amendments on small entities, I certify that this action will not have a significant economic impact on a substantial number of small entities. In determining whether a rule has a significant economic impact on a substantial number of small entities, the impact of concern is any significant adverse economic impact on small entities, because the primary purpose of the regulatory flexibility analysis is to identify and address regulatory alternatives ``which minimize any significant economic impact of the rule on small entities.'' 5 U.S.C. 603 and 604. Thus, an agency may certify that a rule will not have a significant economic impact on a substantial number of small entities if the rule relieves regulatory burden, or otherwise has a positive economic effect on all of the small entities subject to the rule.
  
  Today's proposed amendments will not impose any new requirements on small entities, and will reduce some of the burden established under the promulgated rule. We have therefore concluded that today's proposed amendments will relieve regulatory burden by, for example, exempting all emission sources in the affected source not requiring control under the OLD NESHAP from notification, recordkeeping, and reporting requirements, except as otherwise specified for all affected small entities; excluding from the affected source three types of equipment-- storage tanks, transfer racks, and equipment leak components--under certain conditions that are used in special operations and to conduct maintenance activities; and proposing that owners or operators of existing sources be allowed to request a compliance extension of up to 1 year if the additional time is necessary for the installation of controls. We continue to be interested in the potential impacts of the proposed rule on small entities and welcome comments on issues related to such impacts.
  
  [[Page 69219]]
4. Unfunded Mandates Reform Act
  
  Title II of the Unfunded Mandates Reform Act of 1995 (UMRA), Public Law 104-4, establishes requirements for Federal agencies to assess the effects of their regulatory actions on State, local, and tribal governments and the private sector. Under section 202 of the UMRA, the EPA generally must prepare a written statement, including a cost- benefit analysis, for proposed and final rules with ``Federal mandates'' that may result in expenditures to State, local, and tribal governments, in the aggregate, or to the private sector, of $100 million or more in any 1 year. Before promulgating an EPA rule for which a written statement is needed, section 205 of the UMRA generally requires the EPA to identify and consider a reasonable number of regulatory alternatives and adopt the least costly, most cost-effective or least burdensome alternative that achieves the objectives of the rule. The provisions of section 205 do not apply when they are inconsistent with applicable law. Moreover, section 205 allows the EPA to adopt an alternative other than the least costly, most cost- effective, or least burdensome alternative if the Administrator publishes with the final rule an explanation of why that alternative was not adopted. Before the EPA establishes any regulatory requirements that may significantly or uniquely affect small governments, including tribal governments, it must have developed under section 203 of the UMRA a small government agency plan. The plan must provide for notifying potential affected small governments, enabling officials of affected small governments to have meaningful and timely input in the development of EPA regulatory proposals with significant Federal intergovernmental mandates, and informing, educating, and advising small governments on compliance with the regulatory requirements.
  
  EPA has determined that the proposed amendments do not contain a Federal mandate that may result in expenditures of $100 million or more for State, local, and tribal governments, in aggregate, or the private sector in any 1 year, nor do the proposed amendments significantly or uniquely impact small governments, because they contain no requirements that apply to such governments or impose obligations upon them. Thus, the requirements of the UMRA do not apply to the proposed amendments.
5. Executive Order 13132: Federalism
  
  Executive Order 13132, (64 FR 43255, August 10, 1999) requires EPA to develop an accountable process to ensure ``meaningful and timely input by State and local officials in the development of regulatory policies that have federalism implications.'' ``Policies that have federalism implications'' is defined in the Executive Order to include regulations that have ``substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.''
  
  Today's proposed amendments do not have federalism implications. The proposed amendments correct typographical errors, clarify provisions, or eliminate unnecessary recordkeeping and reporting requirements for emission sources for which there are no control requirements. These changes do not modify existing or create new responsibilities among EPA Regional Offices, States, or local enforcement agencies. The proposed amendments will not have new substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government, as specified in Executive Order 13132. Thus, Executive Order 13132 does not apply to the proposed amendments.
6. Executive Order 13175: Consultation and Coordination With Indian Tribal Governments
  
  Executive Order 13175 (65 FR 67249, November 9, 2000), requires EPA to develop an accountable process to ensure ``meaningful and timely input by tribal officials in the development of regulatory policies that have tribal implications.'' The proposed amendments do not have tribal implications as specified in Executive Order 13175. They would not have substantial direct effects on tribal governments, on the relationship between the Federal government and Indian tribes, or on the distribution of power and responsibilities between the Federal government and Indian tribes, as specified in Executive Order 13175. Thus, Executive Order 13175 does not apply to these proposed amendments.
7. Executive Order 13045: Protection of Children From Environmental Health Risks and Safety Risks
  
  Executive Order 13045 (62 FR 19885, April 23, 1997) applies to any rule that: (1) Is determined to be ``economically significant'' as defined under Executive Order 12866, and (2) concerns an environmental health or safety risk that EPA has reason to believe may have a disproportionate effect on children. If the regulatory action meets both criteria, the Agency must evaluate the environmental health or safety effects of the planned rule on children, and explain why the planned regulation is preferable to other potentially effective and reasonably feasible alternatives considered by the Agency.
  
  EPA interprets Executive Order 13045 as applying only to those regulatory actions that are based on health or safety risks, such that the analysis required under section 5-501 of the Executive Order has the potential to influence the regulation. Today's proposed amendments are not subject to Executive Order 13045 because they do not establish an environmental standard intended to mitigate health or safety risks.
8. Executive Order 13211: Actions Concerning Regulations That Significantly Affect Energy, Supply, Distribution, or Use
  
  The proposed rule is not a ``significant energy action'' as defined in Executive Order 13211, ``Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution, or Use'' (66 FR 28355, May 22, 2001) because it is not likely to have a significant adverse effect on the supply, distribution, or use of energy. Further, we have concluded that this rule is not likely to have any adverse energy effects.
National Technology Transfer and Advancement Act

Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (``NTTAA''), Public Law 104-113, 12(d) (15 U.S.C. 272 note) directs EPA to use voluntary consensus standards in its regulatory activities unless to do so would be inconsistent with applicable law or otherwise impractical. Voluntary consensus standards are technical standards (e.g., materials specifications, test methods, sampling procedures, and business practices) that are developed or adopted by voluntary consensus standards bodies. The NTTAA directs EPA to provide Congress, through OMB, explanations when the Agency decides not to use available and applicable voluntary consensus standards. In the preamble to the OLD NESHAP, we indicated that we had revised the rule to include three voluntary consensus methods, including ASTM D7420-99, Standard Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass Spectrometry (GC/MS), as an alternative to Method 18. While we did

[[Page 69220]]

include two of the three voluntary consensus methods, we neglected to add ASTM D7420-99 to the final rule. Therefore, we are proposing language adding ASTM D7420-99 as an alternative to Method 18 to determine compliance with the organic HAP or TOC emission limit under certain circumstances.

List of Subjects in 40 CFR Part 63

Environmental protection, Administrative practice and procedure, Air pollution control, Hazardous substances, Intergovernmental relations, Reporting and recordkeeping requirements.

Dated: October 31, 2005. Stephen L. Johnson, Administrator.

For the reasons set out in the preamble, title 40, chapter I, part 63 of the Code of Federal Regulations is proposed to be amended as follows:

PART 63--[AMENDED]
1. The authority citation for part 63 continues to read as follows:
  
  Authority: 42 U.S.C. 7401, et seq.
2. Section 63.14 is amended by revising paragraph (b)(29) to read as follows:
  
  Sec. 63.14 Incorporation by reference.
  
  * * * * *
  
  (b) * * *
  
  (29) ASTM D6420-99, Standard Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass Spectrometry, IBR approved for Sec. Sec. 63.2354, 63.5799, and 63.5850. * * * * *
  
  Subpart EEEE--[Amended]
3. Section 63.2338 is amended by:
  1. Revising paragraphs (b)(3) and (b)(4);
  2. By adding a new paragraph (b)(5);
  3. Revising paragraph (c)(1);
  4. Removing paragraph (c)(2) and redesignating paragraphs (c)(3) and (c)(4) as (c)(2) and (c)(3), respectively; and
  5. Revising newly designated paragraphs (c)(2) and (c)(3) to read as follows:
  Sec. 63.2338 What parts of my plant does this subpart cover?
  
  * * * * *
  
  (b) * * *
  
  (3) All equipment leak components in organic liquids service that are associated with:
  
  (i) Storage tanks storing organic liquids;
  
  (ii) Transfer racks loading or unloading organic liquids;
  
  (iii) Pipelines that transfer organic liquids directly between two storage tanks that are subject to this subpart;
  
  (iv) Pipelines that transfer organic liquids directly between a storage tank subject to this subpart and a transfer rack subject to this subpart; and
  
  (v) Pipelines that transfer organic liquids directly between two transfer racks that are subject to this subpart.
  
  (4) All transport vehicles while they are loading or unloading organic liquids at transfer racks subject to this subpart.
  
  (5) All containers while they are loading or unloading organic liquids at transfer racks subject to this subpart.
  
  (c) * * *
  
  (1) Storage tanks, transfer racks, transport vehicles, containers, and equipment leak components that are part of an affected source under another 40 CFR part 63 national emission standards for hazardous air pollutants (NESHAP).
  
  (2) Non-permanent storage tanks, transfer racks, transport vehicles, containers, and equipment leak components when used in special situation distribution loading and unloading operations (such as maintenance or upset liquids management).
  
  (3) Storage tanks, transfer racks, transport vehicles, containers, and equipment leak components when used to conduct maintenance activities, such as stormwater management, liquid removal from tanks for inspections and maintenance, or changeovers to a different liquid stored in a storage tank. * * * * *
4. Section 63.2342 is amended by:
  1. Revising paragraph (a) introductory text;
  2. Adding paragraph (a)(3);
  3. Revising paragraph (b)(1);
  4. Adding paragraph (b)(3); and
  5. Revising paragraph (d) to read as follows:
  Sec. 63.2342 When do I have to comply with this subpart?
  
  (a) If you have a new or reconstructed affected source, you must comply with this subpart according to the schedule identified in paragraph (a)(1), (2), or (3) of this section, as applicable. * * * * *
  
  (3) If, after startup of a new affected source, the total actual annual facility-level organic liquid loading volume at that source exceeds the criteria for control in Table 2 to this subpart, items 9 and 10, the owner or operator must comply with the transfer rack requirements specified in Sec. 63.2346(b) immediately; that is, be in compliance the first day of the period following the end of the 3-year period triggering the control criteria.
  
  (b)(1) If you have an existing affected source, you must comply with the emission limitations, operating limits, and work practice standards for existing affected sources no later than February 5, 2007, except as provided in paragraphs (b)(2) and (3) of this section. * * * * *
  
  (3)(i) If an addition or change other than reconstruction as defined in Sec. 63.2 is made to an existing affected facility that causes the total actual annual facility-level organic liquid loading volume to exceed the criteria for control in Table 2 to this subpart, items 7 and 8, the owner or operator must comply with the transfer rack requirements specified in Sec. 63.2346(b) immediately; that is, be in compliance the first day of the period following the end of the 3-year period triggering the control criteria.
  
  (ii) If the owner or operator believes that compliance with the transfer rack emission limits cannot be achieved immediately, as specified in paragraph (b)(3)(i) of this section, the owner or operator may submit a request for a compliance extension, as specified in paragraphs (b)(3)(ii)(A) through (I) of this section. Subject to paragraph (b)(3)(ii)(B) of this section, until an extension of compliance has been granted by the Administrator (or a State with an approved permit program) under this paragraph (b)(3)(ii), the owner or operator of the transfer rack subject to the requirements of this section shall comply with all applicable requirements of this subpart. Advice on requesting an extension of compliance may be obtained from the Administrator (or the State with an approved permit program).
  
  (A) Submittal. The owner or operator shall submit a request for a compliance extension to the Administrator (or a State, when the State has an approved 40 CFR part 70 permit program and the source is required to obtain a 40 CFR part 70 permit under that program, or a State, when the State has been delegated the authority to implement and enforce the emission standard for that source) seeking an extension allowing the source up to 1 additional year to comply with the transfer rack standard, if such additional period is necessary for the installation of controls. The owner or operator of the affected source who has requested an extension of compliance under this paragraph (b)(3)(ii)(A) and who is otherwise required to obtain a title V permit shall apply for such permit, or apply to have the source's
  
  [[Page 69221]]
  
  title V permit revised to incorporate the conditions of the extension of compliance. The conditions of an extension of compliance granted under this paragraph (b)(3)(ii)(A) will be incorporated into the affected source's title V permit according to the provisions of 40 CFR part 70 or Federal title V regulations in this chapter (42 U.S.C. 7661), whichever are applicable.
  
  (B) When to submit. (1) Any request submitted under paragraph (b)(3)(ii)(A) of this section must be submitted in writing to the appropriate authority no later than 120 days prior to the affected source's compliance date (as specified in paragraph (b)(3)(i) of this section), except as provided for in paragraph (b)(3)(ii)(B)(2) of this section. Nonfrivolous requests submitted under this paragraph (b)(3)(ii)(B)(1) will stay the applicability of the rule as to the emission points in question until such time as the request is granted or denied. A denial will be effective as of the date of denial.
  
  (2) An owner or operator may submit a compliance extension request after the date specified in paragraph (b)(3)(ii)(B)(1) of this section provided the need for the compliance extension arose after that date, and before the otherwise applicable compliance date and the need arose due to circumstances beyond reasonable control of the owner or operator. This request must include, in addition to the information required in paragraph (b)(3)(ii)(C) of this section, a statement of the reasons additional time is needed and the date when the owner or operator first learned of the problems. Nonfrivolous requests submitted under this paragraph (b)(3)(ii)(B)(2) will stay the applicability of the rule as to the emission points in question until such time as the request is granted or denied. A denial will be effective as of the original compliance date.
  
  (C) Information required. The request for a compliance extension under paragraph (b)(3)(ii)(A) of this section shall include the following information:
  
  (1) The name and address of the owner or operator and the address of the existing source if it differs from the address of the owner or operator;
  
  (2) The name, address, and telephone number of a contact person for further information;
  
  (3) An identification of the organic liquid distribution operation and of the specific equipment for which additional compliance time is required;
  
  (4) A description of the controls to be installed to comply with the standard;
  
  (5) Justification for the length of time being requested; and
  
  (6) A compliance schedule, including the date by which each step toward compliance will be reached. At a minimum, the list of dates shall include:
  
  (i) The date by which on-site construction, installation of emission control equipment, or a process change is planned to be initiated;
  
  (ii) The date by which on-site construction, installation of emission control equipment, or a process change is to be completed; and
  
  (iii) The date by which final compliance is to be achieved.
  
  (D) Approval of request for extension of compliance. Based on the information provided in any request made under paragraph (b)(3)(ii)(C) of this section, or other information, the Administrator (or the State with an approved permit program) may grant an extension of compliance with the transfer rack emission standard, as specified in paragraph (b)(3)(ii) of this section. The extension will be in writing and will--
  
  (1) Identify each affected source covered by the extension;
  
  (2) Specify the termination date of the extension;
  
  (3) Specify the dates by which steps toward compliance are to be taken, if appropriate;
  
  (4) Specify other applicable requirements to which the compliance extension applies (e.g., performance tests);
  
  (5) Specify the contents of the progress reports to be submitted and the dates by which such reports are to be submitted, if required pursuant to paragraph (b)(3)(ii)(E) of this section.
  
  (6) Under paragraph (b)(3)(ii) of this section, specify any additional conditions that the Administrator (or the State) deems necessary to assure installation of the necessary controls and protection of the health of persons during the extension period.
  
  (E) Progress reports. The owner or operator of an existing source that has been granted an extension of compliance under paragraph (b)(3)(ii)(D) of this section may be required to submit to the Administrator (or the State with an approved permit program) progress reports indicating whether the steps toward compliance outlined in the compliance schedule have been reached.
  
  (F) Notification of approval or intention to deny. (1) The Administrator (or the State with an approved permit program) will notify the owner or operator in writing of approval or intention to deny approval of a request for an extension of compliance within 30 calendar days after receipt of sufficient information to evaluate a request submitted under paragraph (b)(3)(ii) of this section. The Administrator (or the State) will notify the owner or operator in writing of the status of his/her application; that is, whether the application contains sufficient information to make a determination, within 30 calendar days after receipt of the original application and within 30 calendar days after receipt of any supplementary information that is submitted. The 30-day approval or denial period will begin after the owner or operator has been notified in writing that his/her application is complete. Failure by the Administrator to act within 30 calendar days to approve or disapprove a request submitted under paragraph (b)(3)(ii) of this section does not constitute automatic approval of the request.
  
  (2) When notifying the owner or operator that his/her application is not complete, the Administrator will specify the information needed to complete the application and provide notice of opportunity for the applicant to present, in writing, within 30 calendar days after he/she is notified of the incomplete application, additional information or arguments to the Administrator to enable further action on the application.
  
  (3) Before denying any request for an extension of compliance, the Administrator (or the State with an approved permit program) will notify the owner or operator in writing of the Administrator's (or the State's) intention to issue the denial, together with:
  
  (i) Notice of the information and findings on which the intended denial is based; and
  
  (ii) Notice of opportunity for the owner or operator to present in writing, within 15 calendar days after he/she is notified of the intended denial, additional information or arguments to the Administrator (or the State) before further action on the request.
  
  (4) The Administrator's final determination to deny any request for an extension will be in writing and will set forth the specific grounds on which the denial is based. The final determination will be made within 30 calendar days after presentation of additional information or argument (if the application is complete), or within 30 calendar days after the final date specified for the presentation if no presentation is made.
  
  (G) Termination of extension of compliance. The Administrator (or the State with an approved permit program) may terminate an extension of compliance at an earlier date than specified if any specification under paragraph (b)(3)(ii)(D)(3) or (4) of this section is not met. Upon a determination to terminate, the
  
  [[Page 69222]]
  
  Administrator will notify, in writing, the owner or operator of the Administrator's determination to terminate, together with:
  
  (1) Notice of the reason for termination; and
  
  (2) Notice of opportunity for the owner or operator to present in writing, within 15 calendar days after he/she is notified of the determination to terminate, additional information or arguments to the Administrator before further action on the termination.
  
  (3) A final determination to terminate an extension of compliance will be in writing and will set forth the specific grounds on which the termination is based. The final determination will be made within 30 calendar days after presentation of additional information or arguments, or within 30 calendar days after the final date specified for the presentation if no presentation is made.
  
  (H) The granting of an extension under this section shall not abrogate the Administrator's authority under section 114 of the Clean Air Act.
  
  (I) Limitation on use of compliance extension. The owner or operator may request an extension of compliance under the provisions specified in paragraph (b)(3)(ii) of this section only once for each facility. * * * * *
  
  (d) You must meet the notification requirements in Sec. Sec. 63.2343 and 63.2382(a), as applicable, according to the schedules in Sec. 63.2382(a) and (b)(1) through (3) and in subpart A of this part. Some of these notifications must be submitted before the compliance dates for the emission limitations, operating limits, and work practice standards in this subpart.
5. Section 63.2343 is added to subpart EEEE to read as follows:
  
  Sec. 63.2343 What are my requirements for emission sources not requiring control?
  
  This section establishes the notification, recordkeeping, and reporting requirements for emission sources identified in Sec. 63.2338 that do not require control under this subpart (i.e., under paragraphs (a) through (e) of Sec. 63.2346). Such emission sources are not subject to any other notification, recordkeeping, or reporting sections in this subpart, including Sec. 63.2350(c), except as indicated in paragraphs (a) through (d) of this section.
  
  (a) For each storage tank subject to this subpart having a capacity of less than 18.9 cubic meters (5,000 gallons) and for each transfer rack subject to this subpart that only unloads organic liquids (i.e., no organic liquids are loaded at any of the transfer racks), you must keep documentation that verifies that each storage tank and transfer rack identified in paragraph (a) of this section is not required to be controlled. The documentation must be kept up-to-date (i.e., all such emission sources at a facility are identified in the documentation regardless of when the documentation was last compiled) and must be in a form suitable and readily available for expeditious inspection and review according to Sec. 63.10(b)(1), including records stored in electronic form in a separate location.
  
  (b) For each storage tank subject to this subpart having a capacity of 18.9 cubic meters (5,000 gallons) or more that is not subject to control based on the criteria specified in Table 2 to this subpart, items 1 through 6, you must comply with the requirements specified in paragraphs (b)(1) through (3) of this section.
  
  (1)(i) You must submit the information in Sec. 63.2386(c)(1), (c)(2), (c)(3), and (c)(10)(i) in either the Notification of Compliance Status, according to the schedule specified in Table 12 to this subpart, or in your first Compliance report, according to the schedule specified in Sec. 63.2386(b), whichever occurs first.
  
  (ii)(A) If you submit your first Compliance report before your NOCS, the NOCS must contain the information specified in Sec. 63.2386(d)(3) and (4) if any of the changes identified in paragraph (d) of this section have occurred since the filing of the first Compliance report. If none of the changes identified in paragraph (d) of this section have occurred since the filing of the first compliance report, you do not need to report the information specified in Sec. 63.2386(c)(10)(i) when you submit your NOCS.
  
  (B) If you submit your NOCS before your first compliance report, your first Compliance report must contain the information specified in Sec. 63.2386(d)(3) and (4) if any of the changes specified in paragraph (d) of this section have occurred since the filing of the NOCS.
  
  (iii) If you are already submitting a NOCS or a first Compliance report under Sec. 63.2386(c), you do not need to submit a separate NOCS or first Compliance report for each storage tank that meets the conditions identified in paragraph (b) of this section (i.e., a single NOCS or first Compliance report should be submitted).
  
  (2)(i) You must submit a subsequent Compliance report according to the schedule in Sec. 63.2386(b) whenever any of the events in paragraph (d) of this section occur, as applicable.
  
  (ii) Your subsequent Compliance reports must contain the information in Sec. 63.2386(c)(1), (2), (3) and, as applicable, in Sec. 63.2386(d)(3) and (4). If you are already submitting a subsequent Compliance report under Sec. 63.2386(d), you do not need to submit a separate subsequent Compliance report for each storage tank that meets the conditions identified in paragraph (b) of this section (i.e., a single subsequent Compliance report should be submitted).
  
  (3) For each storage tank that meets the conditions identified in paragraph (b) of this section, you must keep documentation, including a record of the annual average true vapor pressure of the total Table 1 organic HAP in the stored organic liquid, that verifies the storage tank is not required to be controlled under this subpart. The documentation must be kept up-to-date and must be in a form suitable and readily available for expeditious inspection and review according to Sec. 63.10(b)(1), including records stored in electronic form in a separate location.
  
  (c) For each transfer rack subject to this subpart that loads organic liquids but is not subject to control based on the criteria specified in Table 2 to this subpart, items 7 through 10, you must comply with the requirements specified in paragraphs (c)(1) through (3) of this section.
  
  (1)(i) You must submit the information in Sec. 63.2386(c)(1), (c)(2), (c)(3), and (c)(10)(i) in either the Notification of Compliance Status, according to the schedule specified in Table 12 to this subpart, or a first Compliance report, according to the schedule specified in Sec. 63.2386(b), whichever occurs first.
  
  (ii)(A) If you submit your first Compliance report before your NOCS, the NOCS must contain the information specified in Sec. 63.2386(d)(3) and (4) if any of the changes identified in paragraph (d) of this section have occurred since the filing of the first Compliance report. If none of the changes identified in paragraph (d) of this section have occurred since the filing of the first compliance report, you do not need to report the information specified in Sec. 63.2386(c)(10)(i) when you submit your NOCS.
  
  (B) If you submit your NOCS before your first compliance report, your first Compliance report must contain the information specified in Sec. 63.2386(d)(3) and (4) if any of the changes specified in paragraph (d) of this section have occurred since the filing of the NOCS.
  
  (iii) If you are already submitting a NOCS or a first Compliance report under Sec. 63.2386(c), you do not need to submit a separate NOCS or first Compliance report for each transfer rack that meets the conditions identified in
  
  [[Page 69223]]
  
  paragraph (b) of this section (i.e., a single NOCS or first Compliance report should be submitted).
  
  (2)(i) You must submit a subsequent Compliance report according to the schedule in Sec. 63.2386(b) whenever any of the events in paragraph (d) of this section occur, as applicable.
  
  (ii) Your subsequent Compliance reports must contain the information in Sec. 63.2386(c)(1), (2), (3) and, as applicable, in Sec. 63.2386(d)(3) and (4). If you are already submitting a subsequent Compliance report under Sec. 63.2386(d), you do not need to submit a separate subsequent Compliance report for each transfer rack that meets the conditions identified in paragraph (c) of this section (i.e., a single subsequent Compliance report should be submitted).
  
  (3) For each transfer rack that meets the conditions identified in paragraph (c) of this section, you must keep documentation, including the records specified in Sec. 63.2390(d), that verifies the transfer rack is not required to be controlled under this subpart. The documentation must be kept up-to-date and must be in a form suitable and readily available for expeditious inspection and review according to Sec. 63.10(b)(1), including records stored in electronic form in a separate location.
  
  (d) If one or more of the events identified in paragraphs (d)(1) through (4) of this section occur since the filing of the NOCS or the last Compliance report, you must submit a subsequent Compliance report as specified in paragraphs (b)(3) and (c)(3) of this section.
  
  (1) Any storage tank or transfer rack became subject to control under this subpart EEE; or
  
  (2) Any storage tank equal to or greater than 18.9 cubic meters (5,000 gallons) became part of the affected source but is not subject to any of the emission limitations, operating limits, or work practice standards of this subpart; or
  
  (3) Any transfer rack (except those racks at which only unloading of organic liquids occurs) became part of the affected source; or
  
  (4) Any of the information required in Sec. 63.2386(c)(1), (2), or (3) has changed.
6. Section 63.2346 is amended by:
  1. Revising paragraph (a)(2);
  2. Revising paragraph (b) introductory text;
  3. Revising paragraph (b)(2);
  4. Revising paragraph (b)(3);
  5. Revising paragraph (d) introductory text;
  6. Revising paragraph (e); and
  7. Removing and reserving paragraph (h) to read as follows:
  Sec. 63.2346 What emission limitations, operating limits, and work practice standards must I meet?
  
  (a) * * *
  
  (2) Route emissions to fuel gas systems or back into a process as specified in 40 CFR part 63, subpart SS. * * * * *
  
  (b) Transfer racks. For each transfer rack that is part of the collection of transfer racks that meets the total actual annual facility-level organic liquid loading volume criterion for control in Table 2 to this subpart, items 7 through 10, you must comply with paragraph (b)(1), (2), or (3) of this section for each arm in the transfer rack loading an organic liquid whose organic HAP content meets the organic HAP criterion for control in Table 2 to this subpart, items 7 through 10. For existing affected sources, you must comply with paragraph (b)(1), (b)(2), or (b)(3)(i) of this section during the loading of organic liquids into transport vehicles. For new affected sources, you must comply with paragraph (b)(1), (b)(2), or (b)(3)(i) and (ii) of this section during the loading of organic liquids into transport vehicles and containers. If the total actual annual facility- level organic liquid loading volume at any affected source is equal to or greater than the loading volume criteria for control in Table 2 to this subpart, but at a later date is less than the loading volume criteria for control, compliance with paragraph (b)(1), (2), or (3) of this section is no longer required. For new sources and reconstructed sources, as defined in Sec. 63.2338(d) and (e), if at a later date, the total actual annual facility-level organic liquid loading volume again becomes equal to or greater than the loading volume criteria for control in Table 2 to this subpart, the owner or operator must comply with paragraph (b)(1), (b)(2), or (b)(3)(i) and (ii) of this section immediately, as specified in Sec. 63.2342(a)(3). For existing sources, as defined in Sec. 63.2338(f), if at a later date, the total actual annual facility-level organic liquid loading volume again becomes equal to or greater than the loading volume criteria for control in Table 2 to this subpart, the owner or operator must comply with paragraph (b)(1), (b)(2), or (b)(3)(i) of this section immediately, as specified in Sec. 63.2342(b)(3)(i), unless an alternative compliance schedule has been approved under Sec. 63.2342(b)(3)(ii) and subject to the use limitation specified in Sec. 63.2342(b)(3)(ii)(I). * * * * *
  
  (2) Route emissions to fuel gas systems or back into a process as specified in 40 CFR part 63, subpart SS.
  
  (3)(i) Use a vapor balancing system that routes organic HAP vapors displaced from the loading of organic liquids into transport vehicles to the storage tank from which the liquid being loaded originated or to a process unit.
  
  (ii) Use a vapor balancing system that routes the organic HAP vapors displaced from the loading of organic liquids into containers directly (e.g., no intervening tank or containment area such as a room) to the storage tank from which the liquid being loaded originated or to a process unit. * * * * *
  
  (d) Transport vehicles. For each transport vehicle equipped with vapor collection equipment that is loaded at a transfer rack that is subject to control based on the criteria specified in Table 2 to this subpart, items 7 through 10, you must comply with paragraph (d)(1) of this section. For each transport vehicle without vapor collection equipment that is loaded at a transfer rack that is subject to control based on the criteria specified in Table 2 to this subpart, items 7 through 10, you must comply with paragraph (d)(2) of this section. * * * * *
  
  (e) Operating limits. For each high throughput transfer rack, you must meet each operating limit in Table 3 to this subpart for each control device used to comply with the provisions of this subpart whenever emissions from the loading of organic liquids are routed to the control device. For each storage tank and low throughput transfer rack, you must comply with the requirements for monitored parameters as specified in subpart SS of this part for storage vessels and, during the loading of organic liquids, for low throughput transfer racks, respectively. Alternatively, you may comply with the operating limits in Table 3 to this subpart. * * * * *
  
  (h) [Reserved] * * * * *
7. Section 63.2350 is amended by revising paragraph (c) to read as follows:
  
  Sec. 63.2350 What are my general requirements for complying with this subpart?
  
  * * * * *
  
  (c) Except for emission sources not required to be controlled as specified in Sec. 63.2343, you must develop and implement a written startup, shutdown, and malfunction (SSM) plan according to the provisions in Sec. 63.6(e)(3).
8. Section 63.2354 is amended by revising paragraph (b)(3) to read as follows:
  
  [[Page 69224]]
  
  Sec. 63.2354 What performance tests, design evaluations, and performance evaluations must I conduct?
  
  * * * * *
  
  (b) * * *
  
  (3) In addition to EPA Method 25 or 25A of 40 CFR part 60, appendix A, to determine compliance with the organic HAP or TOC emission limit, you may use EPA Method 18 of 40 CFR part 60, appendix A, as specified in paragraph (b)(3)(i) of this section. As an alternative to EPA Method 18, you may use ASTM D6420-99, Standard Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography- Mass Spectrometry (GC/MS) (incorporated by reference, see Sec. 63.14), under the conditions specified in paragraph (b)(3)(ii) of this section.
  
  (i)(A) If you use EPA Method 18 to measure compliance with the percentage efficiency limit, you must first determine which organic HAP are present in the inlet gas stream (i.e., uncontrolled emissions) using knowledge of the organic liquids or the screening procedure described in EPA Method 18. In conducting the performance test, you must analyze samples collected as specified in EPA Method 18, simultaneously at the inlet and outlet of the control device. Quantify the emissions for the same organic HAP identified as present in the inlet gas stream for both the inlet and outlet gas streams of the control device.
  
  (B) If you use EPA Method 18 of 40 CFR part 60, appendix A, to measure compliance with the emission concentration limit, you must first determine which organic HAP are present in the inlet gas stream using knowledge of the organic liquids or the screening procedure described in EPA Method 18. In conducting the performance test, analyze samples collected as specified in EPA Method 18 at the outlet of the control device. Quantify the control device outlet emission concentration for the same organic HAP identified as present in the inlet or uncontrolled gas stream.
  
  (ii) You may use ASTM D6420-99 as an alternative to EPA Method 18 if the target concentration is between 150 ppbv and 100 ppmv and either of the conditions specified in paragraph (b)(2)(ii)(A) or (B) of this section exists. For target compounds not listed in Section 1.1 of ASTM D6420-99 and not amenable to detection by mass spectrometry, you may not use ASTM D6420-99.
  
  (A) The target compounds are those listed in Section 1.1 of ASTM D6420-99; or
  
  (B) For target compounds not listed in Section 1.1 of ASTM D6420- 99, but potentially detected by mass spectrometry, the additional system continuing calibration check after each run, as detailed in ASTM D6420-99, Section 10.5.3, must be followed, met, documented, and submitted with the data report, even if there is no moisture condenser used or the compound is not considered water-soluble. * * * * *
9. Section 63.2362 is amended by revising paragraph (b)(1) to read as follows:
  
  Sec. 63.2362 When must I conduct subsequent performance tests?
  
  * * * * *
  
  (b)(1) For each transport vehicle that you own that is equipped with vapor collection equipment and that is loaded with organic liquids at a transfer rack that is subject to control based on the criteria specified in Table 2 to this subpart, items 7 through 10, you must perform the vapor tightness testing required in Table 5 to this subpart, item 2, on that transport vehicle at least once per year. * * * * *
10. Section 63.2382 is amended by revising paragraphs (d)(2)(iv), (v), (vi), (vii), and (viii) to read as follows:
  
  Sec. 63.2382 What notifications must I submit and when and what information should be submitted?
  
  * * * * *
  
  (d) * * *
  
  (2) * * *
  
  (iv) Descriptions of worst-case operating and/or testing conditions for the control device(s).
  
  (v) Identification of emission sources subject to overlapping requirements described in Sec. 63.2396 and the authority under which you will comply.
  
  (vi) The applicable information specified in Sec. 63.1039(a)(1) through (3) for all pumps and valves subject to the work practice standards for equipment leak components in Table 4 to this subpart, item 4.
  
  (vii) If you are complying with the vapor balancing work practice standard for transfer racks according to Table 4 to this subpart, item 3.a, include a statement to that effect and a statement that the pressure vent settings on the affected storage tanks are greater than or equal to 2.5 pounds per square inch gauge (psig).
  
  (viii) The information specified in Sec. 63.2386(c)(10)(i), unless the information has already been submitted with the first Compliance report. If the information specified in Sec. 63.2386(c)(10)(i) has already been submitted with the first Compliance report, the information specified in Sec. 63.2386(d)(3) and (4), as applicable, shall be submitted instead.
11. Section 63.2386 is amended by:
  1. Revising paragraph (b)(3);
  2. Revising paragraph (c)(4);
  3. Redesignating paragraph (c)(10) as (c)(9) and paragraph (c)(9) as (c)(10);
  4. Revising newly designated paragraphs (c)(9) and (c)(10);
  5. Revising paragraph (d) introductory text;
  6. Removing paragraph (d)(3); and
  7. Adding new paragraphs (d)(3) and (d)(4) to read as follows:
  Sec. 63.2386 What reports must I submit and when and what information is to be submitted in each?
  
  * * * * *
  
  (b) * * *
  
  (3) For each affected source that is subject to permitting regulations pursuant to 40 CFR part 70 or 40 CFR part 71, if the permitting authority has established dates for submitting semiannual reports pursuant to 40 CFR 70.6(a)(3)(iii)(A) or 40 CFR 71.6(a)(3)(iii)(A), you may submit the first and subsequent Compliance reports according to the dates the permitting authority has established instead of according to the dates in paragraphs (b)(1) and (2) of this section.
  
  (c) * * *
  
  (4) Any changes to the information listed in Sec. 63.2382(d)(2) that have occurred since the submittal of the Notification of Compliance Status. * * * * *
  
  (9) A listing of all transport vehicles into which organic liquids were loaded at transfer racks that are subject to control based on the criteria specified in Table 2 to this subpart, items 7 through 10, during the previous 6 months for which vapor tightness documentation as required in Sec. 63.2390(c) was not on file at the facility.
  
  (10)(i) A listing of all transfer racks (except those racks at which only unloading of organic liquids occurs) and of tanks greater than or equal to 18.9 cubic meters (5,000 gallons) that are part of the affected source but are not subject to any of the emission limitations, operating limits, or work practice standards of this subpart.
  
  (ii) If the information specified in paragraph (c)(10)(i) of this section has already been submitted with the NOCS, the information specified in paragraphs (d)(3) and (4) of this section, as applicable, shall be submitted instead.
  
  (d) Subsequent Compliance reports. Subsequent Compliance reports must contain the information in paragraphs (c)(1) through (9) of this section and, where applicable, the information in
  
  [[Page 69225]]
  
  paragraphs (d)(1) through (4) of this section. * * * * *
  
  (3)(i) A listing of any storage tank that became subject to controls based on the criteria for control specified in Table 2 to this subpart, items 1 through 6, since the filing of the last Compliance report.
  
  (ii) A listing of any transfer rack that became subject to controls based on the criteria for control specified in Table 2 to this subpart, items 7 through 10, since the filing of the last Compliance report.
  
  (4)(i) A listing of tanks greater than or equal to 18.9 cubic meters (5,000 gallons) that became part of the affected source but are not subject to any of the emission limitations, operating limits, or work practice standards of this subpart, since the last Compliance report.
  
  (ii) A listing of all transfer racks (except those racks at which only the unloading of organic liquids occurs) that became part of the affected source but are not subject to any of the emission limitations, operating limits, or work practice standards of this subpart, since the last Compliance report. * * * * *
12. Section 63.2390 is amended by:
  1. Revising paragraphs (a) and (b);
  2. Revising paragraph (c) introductory text;
  3. Redesignating paragraph (c)(3) as (d);
  4. Adding a new paragraph (c)(3); and
  5. Revising newly designated paragraph (d) to read as follows:
  Sec. 63.2390 What records must I keep?
  
  (a) For each emission source identified in Sec. 63.2338 that does not require control under this subpart, you must keep all records identified in Sec. 63.2343.
  
  (b) For each emission source identified in Sec. 63.2338 that does require control under this subpart:
  
  (1) You must keep all records identified in subpart SS of this part and in Table 12 to this subpart that are applicable, including records related to notifications and reports, SSM, performance tests, CMS, and performance evaluation plans; and
  
  (2) You must keep the records required to show continuous compliance, as required in subpart SS of this part and in Tables 8 through 10 to this subpart, with each emission limitation, operating limit, and work practice standard that applies to you.
  
  (c) For each transport vehicle into which organic liquids are loaded at a transfer rack that is subject to control based on the criteria specified in Table 2 to this subpart, items 7 through 10, you must keep the applicable records in paragraphs (c)(1) and (2) of this section or alternatively the verification records in paragraph (c)(3) of this section. * * * * *
  
  (3) In lieu of keeping the records specified in paragraph (c)(1) or (2) of this section, as applicable, the owner or operator shall record that the verification of DOT tank certification or Method 27 of appendix A to 40 CFR part 60 testing, required in Table 5 to this subpart, item 2, has been performed. Various methods for the record of verification can be used, such as: a check-off on a log sheet, a list of DOT serial numbers or Method 27 data, or a position description for gate security showing that the security guard will not allow any trucks on site that do not have the appropriate documentation.
  
  (d) You must keep records of the total actual annual facility-level organic liquid loading volume as defined in Sec. 63.2406 through transfer racks to document the applicability, or lack thereof, of the emission limitations in Table 2 to this subpart, items 7 through 10.
13. Section 63.2394 is amended by revising paragraph (a) to read as follows:
  
  Sec. 63.2394 In what form and how long must I keep my records?
  
  (a) Your records must be in a form suitable and readily available for expeditious inspection and review according to Sec. 63.10(b)(1), including records stored in electronic form at a separate location. * * * * *
14. Section 63.2396 is amended by revising paragraphs (a) and (b) to read as follows:
  
  Sec. 63.2396 What compliance options do I have if part of my plant is subject to both this subpart and another subpart?
  
  (a) Compliance with other regulations for storage tanks.--(1) After the compliance dates specified in Sec. 63.2342, you are in compliance with the provisions of this subpart for any storage tank that is assigned to the OLD affected source and that is both controlled with a floating roof and is in compliance with the provisions of either 40 CFR part 60, subpart Kb, or 40 CFR part 61, subpart Y, except that records shall be kept for 5 years rather than 2 years for storage tanks that are assigned to the OLD affected source.
  
  (2) After the compliance dates specified in Sec. 63.2342, you are in compliance with the provisions of this subpart for any storage tank with a fixed roof that is assigned to the OLD affected source and that is both controlled with a closed vent system and control device and is in compliance with either 40 CFR part 60, subpart Kb, or 40 CFR part 61, subpart Y, except that you must comply with the monitoring, recordkeeping, and reporting requirements in this subpart.
  
  (3) As an alternative to paragraphs (a)(1) and (2) of this section, if a storage tank assigned to the OLD affected source is subject to control under 40 CFR part 60, subpart Kb, or 40 CFR part 61, subpart Y, you may elect to comply only with the requirements of this subpart for storage tanks meeting the applicability criteria for control in Table 2 to this subpart.
  
  (b) Compliance with other regulations for transfer racks. After the compliance dates specified in Sec. 63.2342, if you have a transfer rack that is subject to 40 CFR part 61, subpart BB, and that transfer rack is in OLD operation, you must meet all of the requirements of this subpart for that transfer rack when the transfer rack is in OLD operation during the loading of organic liquids. * * * * *
15. Section 63.2402 is amended by revising paragraphs (b)(2), (b)(3), and (b)(4) to read as follows:
  
  Sec. 63.2402 Who implements and enforces this subpart?
  
  * * * * *
  
  (b) * * *
  
  (2) Approval of major changes to test methods under Sec. 63.7(e)(2)(ii) and (f) and as defined in Sec. 63.90.
  
  (3) Approval of major changes to monitoring under Sec. 63.8(f) and as defined in Sec. 63.90.
  
  (4) Approval of major changes to recordkeeping and reporting under Sec. 63.10(f) and as defined in Sec. 63.90.
16. Section 63.2406 is amended by:
  1. Revising the introductory text;
  2. Revising the definitions of ``Shutdown,'' ``Startup,'' ``Transfer rack,'' ``Vapor balancing system,'' and ``Vapor collection system,'' and paragraph (3) of the definition for ``Storage tank;'' and
  3. Adding in alphabetical order definitions for ``Bottoms receivers,'' ``High throughput transfer rack,'' ``Low throughput transfer rack,'' ``Surge control vessel,'' and ``Total actual annual facility-level organic liquid loading volume'' to read as follows:
  Sec. 63.2406 What definitions apply to this subpart?
  
  Terms used in this subpart are defined in the CAA, in Sec. 63.2, 40 CFR part 63, subparts H, PP, SS, TT, UU, and WW, and in this section. If the same term is defined in another subpart and in this section, it will have the meaning given in this section for purposes of this
  
  [[Page 69226]]
  
  subpart. Notwithstanding the introductory language in Sec. 63.921, the terms ``container'' and ``safety device'' shall have the meaning found in this subpart and not in Sec. 63.921. * * * * *
  
  Bottoms receiver means a tank that collects distillation bottoms before the stream is sent for storage or for further processing downstream. * * * * *
  
  High throughput transfer rack means those transfer racks that transfer into transport vehicles (for existing affected sources) or into transport vehicles and containers (for new affected sources) a total of 11.8 million liters per year or greater of organic liquids. * * * * *
  
  Low throughput transfer rack means those transfer racks that transfer into transport vehicles (for existing affected sources) or into transport vehicles and containers (for new affected sources) less than 11.8 million liters per year of organic liquids. * * * * *
  
  Shutdown means the cessation of operation of an OLD affected source, or portion thereof (other than as part of normal operation of a batch-type operation), including equipment required or used to comply with this subpart, or the emptying and degassing of a storage tank. Shutdown as defined here includes, but is not limited to, events that result from periodic maintenance, replacement of equipment, or repair.
  
  Startup means the setting in operation of an OLD affected source, or portion thereof (other than as part of normal operation of a batch- type operation), for any purpose. Startup also includes the placing in operation of any individual piece of equipment required or used to comply with this subpart including, but not limited to, control devices and monitors.
  
  Storage tank * * *
  
  (3) Bottoms receivers; * * * * *
  
  Surge control vessel means feed drums, recycle drums, and intermediate vessels. Surge control vessels are used within chemical manufacturing processes when in-process storage, mixing, or management of flow rates or volumes is needed to assist in production of a product. * * * * *
  
  Total actual annual facility-level organic liquid loading volume means the total facility-level actual volume of organic liquid loaded for transport within or out of the facility through transfer racks that are part of the affected source into transport vehicles (for existing affected sources) or into transport vehicles and containers (for new affected sources) based on a 3-year rolling average, calculated annually.
  
  (1) For existing affected sources, each 3-year rolling average is based on actual facility-level loading volume during each calendar year (January 1 through December 31) in the 3-year period. For calendar year 2004 only (the first year of the initial 3-year rolling average), if an owner or operator of an affected source does not have actual loading volume data for the time period from January 1, 2004, through February 2, 2004 (the time period prior to the effective date of the OLD NESHAP), the owner or operator shall compute a facility-level loading volume for this time period as follows: At the end of the 2004 calendar year, the owner or operator shall calculate a daily average facility- level loading volume (based on the actual loading volume for February 3, 2004, through December 31, 2004) and use that daily average to estimate the facility-level loading volume for the period of time from January 1, 2004, through February 2, 2004. The owner or operator shall then sum the estimated facility-level loading volume from January 1, 2004, through February 2, 2004, and the actual facility-level loading volume from February 3, 2004, through December 31, 2004, to calculate the annual facility-level loading volume for calendar year 2004.
  
  (2)(i) For new affected sources, the 3-year rolling average is calculated as an average of three 12-month periods. An owner or operator must select as the beginning calculation date with which to start the calculations as either the initial startup date of the new affected source or the first day of the calendar month following the month in which startup occurs. Once selected, the date with which the calculations begin cannot be changed.
  
  (ii) The initial 3-year rolling average is based on the projected maximum facility-level annual loading volume for each of the 3 years following the selected beginning calculation date. The second 3-year rolling average is based on actual facility-level loading volume for the first year of operation plus a new projected maximum facility-level annual loading volume for second and third years following the selected beginning calculation date. The third 3-year rolling average is based on actual facility-level loading volume for the first 2 years of operation plus a new projected maximum annual facility-level loading volume for the third year following the beginning calculation date. Subsequent 3-year rolling averages are based on actual facility-level loading volume for each year in the 3-year rolling average.
  
  Transfer rack means a single system used to load organic liquids into, or unload organic liquids out of, transport vehicles or containers. It includes all loading and unloading arms, pumps, meters, shutoff valves, relief valves, and other piping and equipment necessary for the transfer operation. Transfer equipment and operations that are physically separate (i.e., do not share common piping, valves, and other equipment) are considered to be separate transfer racks. * * * * *
  
  Vapor balancing system means a piping system that collects organic HAP vapors displaced from transport vehicles or containers during loading and routes the collected vapors to the storage tank from which the liquid being loaded originated or compresses the vapors for direct conveyance to a chemical manufacturing process unit. For containers, the piping system must route the displaced vapors directly to the appropriate storage tank or process unit in order to qualify as a vapor balancing system.
  
  Vapor collection system means any equipment located at the source (i.e., at the OLD operation) that is not open to the atmosphere; that is composed of piping, connections, and, if necessary, flow-inducing devices; and that is used for:
  
  (1) Containing and conveying vapors displaced during the loading of transport vehicles to a control device;
  
  (2) Containing and directly conveying vapors displaced during the loading of containers; or
  
  (3) Vapor balancing. This does not include any of the vapor collection equipment that is installed on the transport vehicle. * * * * *
17. Table 2 to Subpart EEEE of Part 63 is amended by revising entries 1, 6, 7, 8, 9, and 10 to read as follows:
  
  [[Page 69227]]
  
  Table 2 to Subpart EEEE of Part 63.--Emission Limits * * * * * * *
  
  If you own or operate . . . And if . . . Then you must . . .
18. A storage tank at an a. The stored
  1. Reduce emissions existing affected source organic liquid is of total organic with a capacity >=18.9
  not crude oil and HAP (or, upon cubic meters (5,000
  
  if the annual
  
  approval, TOC) by gallons) and =27.6 than or equal to 20 kilopascals (4.0 ppmv, on a dry psia) and =76.6 than or equal to 20 kilopascals (11.1 ppmv, on a dry psia).
  
  basis corrected to 3% oxygen for combustion devices using supplemental combustion air, by venting emissions through a closed vent system to any combination of control devices meeting the applicable requirements of 40 CFR part 63, subpart SS; OR ii. Comply with the work practice standards specified in Table 4 to this subpart, item 2.a, for tanks storing the liquids described in that table. 7. A transfer rack at an a. The total Table 1 i. For all such existing facility where the organic HAP content loading arms at the total actual annual
  
  of the organic
  
  rack, reduce facility-level organic
  
  liquid being loaded emissions of total liquid loading volume
  
  through one or more organic HAP (or, through transfer racks is of the transfer upon approval, TOC) equal to or greater than rack's arms is at from the loading of 800,000 gallons and less least 98% by weight organic liquids than 10 million gallons. and is being loaded either by venting into a transport the emissions that vehicle.
  
  occur during loading through a closed vent system to any combination of control devices meeting the applicable requirements of 40 CFR part 63, subpart SS, achieving at least 98 weight-percent HAP reduction, OR, as an option, to an exhaust concentration less than or equal to 20 ppmv, on a dry basis corrected to 3% oxygen for combustion devices using supplemental combustion air; OR ii. During the loading of organic liquids, comply with the work practice standards specified in item 3 of Table 4 to this subpart. 8. A transfer rack at an a. One or more of i. See the existing facility where the the transfer rack's requirements in total actual annual
  
  arms is loading an items 7.a.i and facility-level organic
  
  organic liquid into 7.a.ii of this liquid loading volume
  
  a transport
  
  table. through transfer racks is vehicle. >=10 million gallons. 9. A transfer rack at a new a. The total Table 1 i. See the facility where the total organic HAP content requirements in actual annual facility- of the organic
  
  items 7.a.i and level organic liquid
  
  liquid being loaded 7.a.ii of this loading volume through
  
  through one or more table. transfer racks is less than of the transfer 800,000 gallons.
  
  rack's arms is at least 25% by weight and is being loaded into a transport vehicle. b. One or more of i. For all such the transfer rack's loading arms at the arms is filling a rack during the container with a loading of organic capacity equal to liquids, comply or greater than 55 with the provisions gallons.
  
  of Sec. Sec. 63.924 through 63.927 of 40 CFR part 63, Subpart PP--National Emission Standards for Containers, Container Level 3 controls; OR ii. During the loading of organic liquids, comply with the work practice standards specified in item 3.a of Table 4 to this subpart.
  
  [[Page 69228]]
19. A transfer rack at a new a. One or more of i. See the facility where the total the transfer rack's requirements in actual annual facility- arms is loading an items 7.a.i and level organic liquid
  
  organic liquid into 7.a.ii of this loading volume through
  
  a transport
  
  table. transfer racks is equal to vehicle.
  1. For all such or greater than 800,000 b. One or more of loading arms at the gallons.
  the transfer rack's rack during the arms is filling a loading of organic container with a liquids, comply capacity equal to with the provisions or greater than 55 of Sec. Sec. gallons.
  
  63.924 through 63.927 of 40 CFR part 63, Subpart PP--National Emission Standards for Containers, Container Level 3 controls; OR ii. During the loading of organic liquids, comply with the work practice standards specified in item 3.a of Table 4 to this subpart.
20. Table 3 to Subpart EEEE of Part 63 is amended by revising entries 3, 5, and 6 to read as follows:
  
  Table 3 to Subpart EEEE of Part 63.--Operating Limits--High Throughput Transfer Racks * * * * * * *
  
  For each existing, each reconstructed, and each new affected
  
  You must . . . source using . . .
  
  * * * * * * * 3. An absorber to comply with an a. Maintain the daily average emission limit in Table 2 to this concentration level of organic subpart.
  
  compounds in the absorber exhaust less than or equal to the reference concentration established during the design evaluation or performance test that demonstrated compliance with the emission limit; OR b. Maintain the daily average scrubbing liquid temperature less than or equal to the reference temperature established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND Maintain the difference between the specific gravities of the saturated and fresh scrubbing fluids greater than or equal to the difference established during the design evaluation or performance test that demonstrated compliance with the emission limit.
  
  * * * * * * * 5. An adsorption system with
  1. Maintain the daily average adsorbent regeneration to comply concentration level of organic with an emission limit in Table 2 to compounds in the adsorber this subpart.
    
    exhaust less than or equal to the reference concentration established during the design evaluation or performance test that demonstrated compliance with the emission limit; OR b. Maintain the total regeneration stream mass flow during the adsorption bed regeneration cycle greater than or equal to the reference stream mass flow established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND Before the adsorption cycle commences, achieve and maintain the temperature of the adsorption bed after regeneration less than or equal to the reference temperature established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND Achieve a pressure reduction during each adsorption bed regeneration cycle greater than or equal to the pressure reduction established during the design evaluation or performance test that demonstrated compliance with the emission limit. 6. An adsorption system without
  2. Maintain the daily average adsorbent regeneration to comply concentration level of organic with an emission limit in Table 2 to compounds in the adsorber this subpart.
    
    exhaust less than or equal to the reference concentration established during the design evaluation or performance test that demonstrated compliance with the emission limit; OR b. Replace the existing adsorbent in each segment of the bed with an adsorbent that meets the replacement specifications established during the design evaluation or performance test before the age of the adsorbent exceeds the maximum allowable age established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND Maintain the temperature of the adsorption bed less than or equal to the reference temperature established during the design evaluation or performance test that demonstrated compliance with the emission limit.
    
    * * * * * * *
21. Table 4 to Subpart EEEE to Part 63 is revised to read as follows:
  
  [[Page 69229]]
  
  Table 4 to Subpart EEEE of Part 63.--Work Practice Standards [As stated in Sec. 63.2346, you may elect to comply with one of the work practice standards for existing, reconstructed, or new affected sources in the following table. If you elect to do so, . . .]
  
  For each . . .
  
  You must . . .
22. Storage tank at an
  1. Comply with the requirements of 40 CFR existing, reconstructed, or part 63, subpart WW (control level 2), new affected source meeting if you elect to meet 40 CFR part 63, any set of tank capacity and subpart WW (control level 2), organic HAP vapor pressure requirements as an alternative to the criteria specified in Table emission limit in Table 2 to this 2 to this subpart, items 1 subpart, items 1 through 5; or through 5.
  2. Comply with the requirements of Sec. 63.984 for routing emissions to a fuel gas system or back to a process. 2. Storage tank at an
  3. Comply with the requirements of Sec. existing, reconstructed, or 63.984 for routing emissions to a fuel new affected source meeting gas system or back to a process. any set of tank capacity and organic HAP vapor pressure criteria specified in Table 2 to this subpart, item 6. 3. Transfer rack subject to a. If the option of a vapor balancing control based on the
    
    system is selected, install and, during criteria specified in Table the loading of organic liquids, operate 2 to this subpart, items 7 a system that meets the requirements in through 10, at an existing, Table 7 to this subpart, item 3.b.i. and reconstructed, or new
    
    item 3.b.ii, as applicable; or affected source.
  4. Comply with the requirements of Sec. 63.984 during the loading of organic liquids, for routing emissions to a fuel gas system or back to a process. 4. Pump, valve, and sampling Comply with the requirements for pumps, connection that operates in valves, and sampling connections in 40 organic liquids service at CFR part 63, subpart TT (control level least 300 hours per year at 1), subpart UU (control level 2), or an existing, reconstructed, subpart H. or new affected source. 5. Transport vehicles
    
    Follow the steps in 40 CFR 60.502(e) to equipped with vapor
    
    ensure that organic liquids are loaded collection equipment that only into vapor-tight transport are loaded at transfer racks vehicles, and comply with the provisions that are subject to control in 40 CFR 60.502(f), (g), (h), and (i), based on the criteria
    
    except substitute the term transport specified in Table 2 to this vehicle at each occurrence of tank truck subpart, items 7 through 10. or gasoline tank truck in those paragraphs. 6. Transport vehicles
    
    Ensure that organic liquids are loaded equipped without vapor
    
    only into transport vehicles that have a collection equipment that current certification in accordance with are loaded at transfer racks the U.S. DOT pressure test requirements that are subject to control in 49 CFR 180 (cargo tanks) or 49 CFR based on the criteria
    
    173.31 (tank cars). specified in Table 2 to this subpart, items 7 through 10.
23. Table 5 to Subpart EEEE of Part 63 is revised to read as follows:
  
  Table 5 to Subpart EEEE of Part 63.--Requirements for Performance Tests and Design Evaluations [As stated in Sec. Sec. 63.2354(a) and 63.2362, you must comply with the requirements for performance tests and design evaluations for existing, reconstructed, or new affected sources as follows]
  
  According to the For . . .
  
  You must conduct . . . According to . . .
  
  Using . . .
  
  To determine . . .
  
  following requirements . . .
24. Each existing, each
  1. A performance test i. Sec. 63.985
  (1) EPA Method 1 or (A) Sampling port (i) Sampling sites reconstructed, and each new
  
  to determine the
  
  (b)(1)(ii), Sec.
  
  1A in appendix A of locations and the must be located at affected source using a nonflare organic HAP (or, upon 63.988(b), Sec.
  
  40 CFR part 60, as required number of the inlet and outlet control device to comply with an approval, TOC)
  
  63.990(b), or Sec. appropriate.
  
  traverse points. of each control emission limit in Table 2 to this control efficiency of 63.995(b).
  
  device if complying subpart, items 1 through 10.
  
  each nonflare control
  
  with the control device, OR the
  
  efficiency exhaust concentration
  
  requirement or at of each combustion
  
  the outlet of the device; OR
  
  control device if complying with the exhaust concentration requirement; AND (ii) the outlet sampling site must be located at each control device prior to any releases to the atmosphere. (2) EPA Method 2, 2A, (A) Stack gas
  
  See the requirements 2C, 2D, 2F, or 2G in velocity and
  
  in items appendix A of 40 CFR volumetric flow rate. 1.a.i.(1)(A) (i) and part 60, as
  
  (ii) of this table. appropriate.
  
  [[Page 69230]]
  
  (3) EPA Method 3 or (A) Concentration of See the requirements 3B in appendix A of CO2 and O2 and dry in items 40 CFR part 60, as molecular weight of 1.a.i.(1)(A) (i) and appropriate.
  
  the stack gas.
  
  (ii) of this table. (4) EPA Method 4 in (A) Moisture content See the requirements appendix A of 40 CFR of the stack gas. in items part 60.
25. a.i.(1)(A) (i) and (ii) of this table. (5) EPA Method 18, (A) Total organic HAP (i) The organic HAP 25, or 25A in
  
  (or, upon approval, used for the appendix A of 40 CFR TOC), or
  
  calibration gas for part 60, as
  
  formaldehyde
  
  EPA Method 25A must appropriate, or EPA emissions.
  
  be the single Method 316 in
  
  organic HAP appendix A of 40 CFR
  
  representing the part 63 for
  
  largest percent by measuring
  
  volume of emissions; formaldehyde.
  
  AND (ii) During the performance test, you must establish the operating parameter limits within which total organic HAP (or, upon approval, TOC) emissions are reduced by the required weight- percent or, as an option for nonflare combustion devices, to 20 ppmv exhaust concentration. b. A design evaluation Sec. 63.985
  
  ..................... ..................... During a design (for nonflare control (b)(1)(i).
  
  evaluation, you must devices) to determine
  
  establish the the organic HAP (or,
  
  operating parameter upon approval, TOC)
  
  limits within which control efficiency of
  
  total organic HAP, each nonflare control
  
  (or, upon approval, device, or the
  
  TOC) emissions are exhaust concentration
  
  reduced by at least of each combustion
  
  95 weight-percent or control device.
  
  as an option to 20 ppmv exhaust concentration. 2. Each transport vehicle that you A performance test to ...................... EPA Method 27 in Vapor tightness...... The pressure change own that is equipped with vapor determine the vapor
  
  appendix A of 40 CFR
  
  in the tank must be collection equipment and is loaded tightness of the tank
  
  part 60.
  
  no more than 250 with organic liquids at a transfer and then repair as
  
  pascals (1 inch of rack that is subject to control needed until it
  
  water) in 5 minutes based on the criteria specified in passes the test.
  
  after it is Table 2 to this subpart, items 7
  
  pressurized to 4,500 through 10, at an existing,
  
  pascals (18 inches reconstructed, or new affected
  
  of water). source.
  
  [[Page 69231]]
26. Table 6 to Subpart EEEE of Part 63 is amended by revising entry 2 to read as follows:
  
  Table 6 to Subpart EEEE of Part 63.--Initial Compliance With Emission Limits * * * * * * *
  
  You have For each . . .
  
  For the following demonstrated initial emission limit . . . compliance if . . .
  
  * * * * * * * 2. Transfer rack that is Reduce total organic Total organic HAP subject to control based on HAP (or, upon
  
  (or, upon approval, the criteria specified in approval, TOC)
  
  TOC) emissions from Table 2 to this subpart, emissions from the the loading of items 7 through 10, at an loading of organic organic liquids, existing, reconstructed, or liquids by at least based on the new affected source.
  
  98 weight-percent, results of the or as an option for performance testing combustion devices or design to an exhaust
  
  evaluation concentration of =300 hours per year at an according to one of subpart you have existing, reconstructed, or the subparts listed selected, OR new affected source.
  
  in Table 4 to this ii. Provide written subpart, item 4.a. specifications for your equivalent control approach.
  
  [[Page 69232]]
27. Table 8 to Subpart EEEE of Part 63 is revised to read as follows:
  
  Table 8 to Subpart EEEE of Part 63.--Continuous Compliance With Emission Limits [As stated in Sec. Sec. 63.2378(a) and (b) and 63.2390(b), you must
  
  show continuous compliance with the emission limits for existing, reconstructed, or new affected sources according to the following table]
  
  You must demonstrate For the following
  
  continuous For each . . .
  
  emission limit . . . compliance by . . .
28. Storage tank at an
  1. Reduce total i. Performing CMS existing, reconstructed, or organic HAP (or, monitoring and new affected source meeting upon approval, TOC) collecting data any set of tank capacity emissions from the according to Sec. and liquid organic HAP
  closed vent system Sec. 63.2366, vapor pressure criteria and control devices 63.2374, and specified in Table 2 to by 95 weight-
  
  63.2378; AND this subpart, items 1
  
  percent or greater, ii. Maintaining the through 6.
  
  or as an option to operating limits 20 ppmv or less of established during total organic HAP the design (or, upon approval, evaluation or TOC) in the exhaust performance test of combustion
  
  that demonstrated devices.
  
  compliance with the emission limit. 2. Transfer rack that is a. Reduce total i. Performing CMS subject to control based on organic HAP (or, monitoring and the criteria specified in upon approval, TOC) collecting data Table 2 to this subpart, emissions during according to Sec. items 7 through 10, at an the loading of
  
  Sec. 63.2366, existing, reconstructed, or organic liquids 63.2374, and new affected source.
  
  from the closed 63.2378 during vent system and loading of organic control device by AND 98 weight-percent ii. Maintaining the or greater, or as operating limits an option to 20 established during ppmv or less of the design total organic HAP evaluation or (or, upon approval, performance test TOC) in the exhaust that demonstrated of combustion
  
  compliance with the devices.
  
  emission limit during the loading of organic liquids.
29. Table 9 to Subpart EEEE of Part 63 is amended by revising entries 2, 3, 4, 5, 6, and 7 to read as follows:
  
  Table 9 to Subpart EEEE of Part 63.--Continuous Compliance With Operating Limits--High Throughput Transfer Racks * * * * * * *
  
  You must demonstrate For each existing,
  
  For the following
  
  continuous reconstructed and each new operating limit . . compliance by . . . affected source using . . .
  
  .
  
  * * * * * * * 2. A catalytic oxidizer to a. Replace the
  1. Replacing the comply with an emission existing catalyst existing catalyst limit in Table 2 to this bed before the age bed before the age subpart.
  of the bed exceeds of the bed exceeds the maximum
  
  the maximum allowable age
  
  allowable age established during established during the design
  
  the design evaluation or
  
  evaluation or performance test performance test that demonstrated that demonstrated compliance with the compliance with the emission limit; AND emission limit; AND ii. Keeping the applicable records required in Sec. 63.998. b. Maintain the i. Continuously daily average
  
  monitoring and temperature at the recording the inlet of the
  
  temperature at the catalyst bed
  
  inlet of the greater than or catalyst bed at equal to the
  
  least every 15 reference
  
  minutes and temperature
  
  maintaining the established during daily average the design
  
  temperature at the evaluation or
  
  inlet of the performance test catalyst bed that demonstrated greater than or compliance with the equal to the emission limit; AND reference temperature established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND ii. Keeping the applicable records required in Sec. 63.998. c. Maintain the i. Continuously daily average
  
  monitoring and temperature
  
  recording the difference across temperature at the the catalyst bed outlet of the greater than or catalyst bed every equal to the
  
  15 minutes and minimum temperature maintaining the difference
  
  daily average established during temperature the design
  
  difference across evaluation or
  
  the catalyst bed performance test greater than or that demonstrated equal to the compliance with the minumum temperature emission limit. difference established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND ii. Keeping the applicable records required Sec. 63.998.
  
  [[Page 69233]]
30. An absorber to comply a. Maintain the i. Continuously with an emission limit in daily average
  
  monitoring the Table 2 to this subpart. concentration level organic of organic
  
  concentration in compounds in the the absorber absorber exhaust exhaust and less than or equal maintaining the to the reference daily average concentration
  
  concentration less established during than or equal to the design
  
  the reference evaluation test concentration that demonstrated established during compliance with the the design emission limit; OR evaluation or performance test that demonstrated compliance with the emission limit; AND ii. Keeping the applicable records required in Sec. 63.998. b. Maintain the i. Continuously daily average
  
  monitoring the scrubbing liquid scrubbing liquid temperature less temperature and than or equal to maintaining the the reference
  
  daily average temperature
  
  temperature less established during than or equal to the design
  
  the reference evaluation or
  
  temperature performance test established during that demonstrated the design compliance with the evaluation or emission limit; AND. performance test Maintain the
  
  that demonstrated difference between compliance with the the specific
  
  emission limit; AND gravities of the ii. Maintaining the saturated and fresh difference between scrubbing fluids the specific greater than or gravities greater equal to the
  
  than or equal to difference
  
  the difference established during established during the design
  
  the design evaluation or
  
  evaluation or performance test performance test that demonstrated that demonstrated compliance with the compliance with the emission limit. emission limit; AND iii. Keeping the applicable records required in Sec. 63.998. 4. A condenser to comply a. Maintain the i. Continuously with an emission limit in daily average
  
  monitoring the Table 2 to this subpart. concentration level organic of organic
  
  concentration at compounds at the the condenser exit exit of the
  
  and maintaining the condenser less than daily average or equal to the concentration less reference
  
  than or equal to concentration
  
  the reference established during concentration the design
  
  established during evaluation or
  
  the design performance test evaluation or that demonstrated performance test compliance with the that demonstrated emission limit; OR compliance with the emission limit: AND ii. Keeping the applicable records required in Sec. 63.998. b. Maintain the i. Continuously daily average
  
  monitoring and condenser exit
  
  recording the temperature less temperature at the than or equal to exit of the the reference
  
  condenser at least temperature
  
  every 15 minutes established during and maintaining the the design
  
  daily average evaluation or
  
  temperature less performance test than or equal to that demonstrated the reference compliance with the temperature emission limit. established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND ii. Keeping the applicable records required in Sec. 63.998. 5. An adsorption system with a. Maintain the i. Continuously adsorbent regeneration to daily average
  
  monitoring the comply with an emission concentration level daily average limit in Table 2 to this of organic
  
  organic subpart.
  
  compounds in the concentration in adsorber exhaust the adsorber less than or equal exhaust and to the reference maintaining the concentration
  
  concentration less established during than or equal to the design
  
  the reference evaluation or
  
  concentration performance test established during that demonstrated the design compliance with the evaluation or emission limit; OR performance test that demonstrated compliance with the emission limit; AND ii. Keeping the applicable records required in Sec. 63.998. b. Maintain the i. Maintaining the total regeneration total regeneration stream mass flow stream mass flow during the
  
  during the adsorption bed
  
  adsorption bed regeneration cycle regeneration cycle greater than or greater than or equal to the
  
  equal to the reference stream reference stream mass flow
  
  mass flow established during established during the design
  
  the design evaluation or
  
  evaluation or performance test performance test that demonstrated that demonstrated compliance with the with the emission emission limit; AND limit; AND Before the
  
  ii. Maintaining the adsorption cycle temperature of the commences, achieve adsorption bed and maintain the after regeneration temperature of the less than or equal adsorption bed
  
  to the reference after regeneration temperature less than or equal established during to the reference the design temperature
  
  evaluation or established during performance test the design
  
  that demonstrated evaluation or
  
  compliance with the performance test; emission limit: AND AND
  
  [[Page 69234]]
  
  Achieve greater than iii. Achieving or equal to the greater than or pressure reduction equal to the during the
  
  pressure reduction adsorption bed
  
  during the regeneration cycle regeneration cycle established during established during the design
  
  the design evaluation or
  
  evaluation or performance test performance test that demonstrated that demonstrated compliance with the compliance with the emission limit. emission limit; AND iv. Keeping the applicable records required in Sec. 63.998. 6. An adsorption system a. Maintain the i. Continuously without adsorbent
  
  daily average
  
  monitoring the regeneration to comply with concentration level organic an emission limit in Table of organic
  
  concentration in 2 to this subpart.
  
  compounds in the the adsorber adsorber exhaust exhaust and less than or equal maintaining the to the reference concentration less concentration
  
  than or equal to established during the reference the design
  
  concentration evaluation or
  
  established during performance test the design that demonstrated evaluation or compliance with the performance test emission limit; OR that demonstrated compliance with the emission limit; AND ii. Keeping the applicable records required in Sec. 63.998. b. Replace the
  1. Replacing the existing adsorbent existing adsorbent, in each segment of in each segment of the bed before the the bed with an age of the
  adsorbent that adsorbent exceeds meets the the maximum
  
  replacement allowable age
  
  specifications established during established during the design
  
  the design evaluation or
  
  evaluation or performance test performance test that demonstrated before the age of compliance with the the adsorbent emission limit; AND exceeds the maximum Maintain the
  
  allowable age temperature of the established during adsorption bed less the design than or equal to evaluation or the reference
  
  performance test temperature
  
  that demonstrated established during compliance with the the design
  
  emission limit; AND evaluation or
  
  ii. Maintaining the performance test temperature of the that demonstrated adsorption bed less compliance with the than or equal to emission limit. the reference temperature established during the design evaluation or performance test that demonstrated compliance with the emission limit; AND iii. Keeping the applicable records required in Sec. 63.998. 7. A flare to comply with an a. Maintain a pilot i. Continuously emission limit in Table 2 flame in the flare operating a device to this subpart.
  
  at all times that that detects the vapors may be
  
  presence of the vented to the flare pilot flame; (Sec.
  
  ii. Keeping the 63.11(b)(5)); AND applicable records required in Sec. 63.998. b. Maintain a flare i. Maintaining a flame at all times flare flame at all that vapors are times that vapors being vented to the are being vented to flare Sec.
  
  the flare; AND 63.11(b)(5)); AND ii. Keeping the applicable records required in Sec. 63.998. c. Operate the flare i. Operating the with no visible flare with no emissions, except visible emissions for up to 5 minutes exceeding the in any 2
  
  amount allowed; AND consecutive hours ii. Keeping the (Sec.
  
  applicable records 63.11(b)(4)); AND required in Sec. EITHER
  
  63.998. d.1. Operate the i. Operating the flare with an exit flare within the velocity that is applicable exit within the
  
  velocity limits; applicable limits AND in Sec.
  
  ii. Operating the 63.11(b)(7) and (8) flare with the gas and with a net
  
  heating value heating value of greater than the the gas being
  
  applicable minimum combusted greater value; AND than the applicable iii. Keeping the minimum value in applicable records Sec.
  
  required in Sec. 63.11(b)(6)(ii); OR 63.998. 2. Adhere to the i. Operating the requirements in flare within the Sec.
  
  applicable limits 63.11(b)(6)(i). in Sec. 63.11(b)(6)(i); AND ii. Keeping the applicable records required in Sec. 63.998.
  
  * * * * * * *
31. Table 10 to Subpart EEEE of Part 63 is amended by revising entries 1, 2, 4, and 5 to read as follows:
  
  [[Page 69235]]
  
  Table 10 to Subpart EEEE of Part 63.--Continuous Compliance With Work Practice Standards * * * * * * *
  
  You must demonstrate For the following
  
  continuous For each . . .
  
  standard . . . compliance by . . .
32. Internal floating roof a. Install a
  1. Visually (IFR) storage tank at an floating roof
    
    inspecting the existing, reconstructed, or designed and
    
    floating roof deck, new affected source meeting operated according deck fittings, and any set of tank capacity, to the applicable rim seals of each and vapor pressure criteria specifications in IFR once per year specified in Table 2 to Sec. 63.1063(a) (Sec. this subpart, items 1
    
    and (b).
    
    63.1063(d)(2)); AND through 5.
    
    ii. Visually inspecting the floating roof deck, deck fittings, and rim seals of each IFR either each time the storage tank is completely emptied and degassed or every 10 years, whichever occurs first (Sec. 63.1063(c)(1), (d)(1), and (e)); AND iii. Keeping the tank records required in Sec. 63.1065. 2. External floating roof a. Install a
  2. Visually (EFR) storage tank at an floating roof
    
    inspecting the existing, reconstructed, or designed and
    
    floating roof deck, new affected source meeting operated according deck fittings, and any set of tank capacity, to the applicable rim seals of each and vapor pressure criteria specifications in EFR either each specified in Table 2 to Sec. 63.1063(a) time the storage this subpart, items 1
    
    and (b).
    
    tank is completely through 5.
    
    emptied and degassed or every 10 years, whichever occurs first (Sec. 63.1063(c)(2), (d), and (e)); AND ii. Performing seal gap measurements on the secondary seal of each EFR at least once every year, and on the primary seal of each EFR at least every 5 years (Sec. 63.1063(c)(2), (d), and (e)); AND iii. Keeping the tank records required in Sec. 63.1065.
    
    * * * * * * * 4. Transfer rack that is a. Ensure that
  3. Ensuring that subject to control based on organic liquids are organic liquids are the criteria specified in loaded into
    
    loaded into Table 2 to this subpart, transport vehicles transport vehicles items 7 through 10, at an in accordance with in accordance with existing, reconstructed, or the requirements in the requirements in new affected source.
    
    Table 4 to this Table 4 to this subpart, items 5 or subpart, items 5 or 6, as applicable. 6, as applicable. b. Install and, i. Monitoring each during the loading potential source of of organic liquids, vapor leakage in operate a vapor the system balancing system. quarterly during the loading of a transport vehicle or the filling of a container using the methods and procedures described in the rule requirements selected for the work practice standard for equipment leak components as specified in Table 4 to this subpart, item 4. An instrument reading of 500 ppmv defines a leak. Repair of leaks is performed according to the repair requirements specified in your selected equipment leak standards. c. Route emissions i. Continuing to to a fuel gas
    
    meet the system or back to a requirements process.
    
    specified in Sec. 63.984(b). 5. Equipment leak component, a. Comply with the i. Carrying out a as defined in Sec.
    
    requirements of 40 leak detection and 63.2406, that operates in CFR part 63,
    
    repair program in organic liquids service at subpart TT, UU, or accordance with the least 300 hours per year. H.
    
    subpart selected from the list in item 5.a of this table.
    
    * * * * * * *
33. Table 11 to Subpart EEEE of Part 63 is revised to read as follows:
  
  Table 11 to Subpart EEEE of Part 63.--Requirements for Reports [As stated in Sec. 63.2386(a) and (b), you must submit compliance reports and startup, shutdown, and malfunction reports according to the following table]
  
  The report must You must submit the
  
  You must submit . . .
  
  contain . . .
  
  report . . .
34. Compliance report, or a. The information Semiannually, and it Periodic Report.
  
  specified in Sec. must be postmarked 63.2386(c), (d), by January 31 or (e). If you had a July 31, in startup, shutdown, accordance with or malfunction
  
  Sec. 63.2386(b). during the reporting period and you took actions consistent with your SSM plan, the report must also include the information in Sec. 63.10(d)(5)(i); AND
  
  [[Page 69236]]
  1. The information See the submission required by 40 CFR requirement in item part 63, subpart 1.a of this table. TT, UU, or H, as applicable, for pumps, valves, and sampling connections; AND c. The information See the submission required by Sec. requirement in item 63.999(c); AND
35. a of this table. d. The information See the submission specified in Sec. requirement in item 63.1066(b)
36. a of this table. including: notification of inspection, inspection results, requests for alternate devices, and requests for extensions, as applicable. 2. Immediate startup,
  1. The information i. By letter within shutdown, and malfunction required in Sec. 7 working days report if you had a
  63.10(d)(5)(ii). after the end of startup, shutdown, or
  
  the event unless malfunction during the
  
  you have made reporting period, and you
  
  alternative took an action that was not
  
  arrangements the consistent with your SSM
  
  permitting plan.
  
  authority (Sec. 63.10(d)(5)(ii)).
37. Table 12 to Subpart EEEE of Part 63 is amended by revising entries Sec. 63.6(e)(3), Sec. 63.7(g), Sec. 63.9(h)(1)-(6), Sec. 63.9(j), and Sec. 63.10(e)(3)(iv)-(v) to read as follows:
  
  Table 12 to Subpart EEEE of Part 63.--Applicability of General Provisions to Subpart EEEE * * * * * * *
  
  Citation
  
  Subject
  
  Brief description Applies to subpart EEEE
  
  * * * * * * * Sec. 63.6(e)(3)................. Startup, Shutdown, Requirement for SSM plan; Yes; however, the 2-day and Malfunction
  
  content of SSM plan;
  
  reporting requirement in (SSM) Plan.
  
  actions during SSM.
  
  paragraph Sec. 63.6(e)(3)(iv) does not apply and Sec. 63.6(e)(3) does not apply to emissions sources not requiring control.
  
  * * * * * * * Sec. 63.7(g).................... Performance Test Data Must include raw data in Yes; however, performance Analysis.
  
  performance test report; test data is to be must submit performance submitted with the NOCS test data 60 days after according to schedule end of test with the
  
  specified in Sec. notification of
  
  63.9(h)(1)-(6) of this compliance status (NOCS); table. keep data for 5 years.
  
  * * * * * * * Sec. 63.9(h)(1)-(6)............. Notification of
  
  Contents due 60 days after Yes; however, there are Compliance Status. end of performance test no opacity standards and or other compliance
  
  all initial NOCS, demonstration, except for including all opacity/VE, which are due performance test data, 30 days after; when to are to be submitted at submit to Federal vs. the same time, either State authority.
  
  within 240 days after the compliance date or within 60 days after the last performance test demonstrating compliance has been completed, whichever occurs first.
  
  * * * * * * * Sec. 63.9(j).................... Change in Previous Must submit within 15 days Yes; except for emission Information.
  
  after the change.
  
  sources not required to be controlled as specified in Sec. 63.2343.
  
  [[Page 69237]]
  
  * * * * * * * Sec. 63.10(e) (3)(iv)-(v)....... Excess Emissions Requirement to revert to Yes. Reports.
  
  quarterly submission if there is an excess emissions or parameter monitoring exceedance (now defined as deviations); provision to request semiannual reporting after compliance for 1 year; submit report by 30th day following end of quarter or calendar half; if there has not been an exceedance or excess emissions (now defined as deviations), report contents in a statement that there have been no deviations; must submit report containing all of the information in Sec. Sec. 63.8(c)(7)-(8) and 63.10(c)(5)-(13).
  
  * * * * * * *
  
  [FR Doc. 05-22108 Filed 11-10-05; 8:45 am]
  
  BILLING CODE 6560-50-P

Subscribers can access the reported version of this case.

You can sign up for a trial and make the most of our service including these benefits.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Subscribers are able to see a list of all the cited cases and legislation of a document.

You can sign up for a trial and make the most of our service including these benefits.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Subscribers are able to see a list of all the documents that have cited the case.

You can sign up for a trial and make the most of our service including these benefits.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Subscribers are able to see the revised versions of legislation with amendments.

You can sign up for a trial and make the most of our service including these benefits.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Subscribers are able to see any amendments made to the case.

You can sign up for a trial and make the most of our service including these benefits.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Subscribers are able to see a visualisation of a case and its relationships to other cases. An alternative to lists of cases, the Precedent Map makes it easier to establish which ones may be of most relevance to your research and prioritise further reading. You also get a useful overview of how the case was received.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Subscribers are able to see the list of results connected to your document through the topics and citations Vincent found.

You can sign up for a trial and make the most of our service including these benefits.

Request your trial

Why Sign-up to vLex?

Over 100 Countries

Search over 120 million documents from over 100 countries including primary and secondary collections of legislation, case law, regulations, practical law, news, forms and contracts, books, journals, and more.
Thousands of Data Sources

Updated daily, vLex brings together legal information from over 750 publishing partners, providing access to over 2,500 legal and news sources from the world’s leading publishers.
Find What You Need, Quickly

Advanced A.I. technology developed exclusively by vLex editorially enriches legal information to make it accessible, with instant translation into 14 languages for enhanced discoverability and comparative research.
Over 2 million registered users

Founded over 20 years ago, vLex provides a first-class and comprehensive service for lawyers, law firms, government departments, and law schools around the world.

Air pollutants, hazardous; national emission standards: Organic liquids distribution (non-gasoline),

You can sign up for a trial and make the most of our service including these benefits.

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users

You can sign up for a trial and make the most of our service including these benefits.

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users

You can sign up for a trial and make the most of our service including these benefits.

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users

You can sign up for a trial and make the most of our service including these benefits.

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users

You can sign up for a trial and make the most of our service including these benefits.

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users

You can sign up for a trial and make the most of our service including these benefits.

Why Sign-up to vLex?

Over 100 Countries

Thousands of Data Sources

Find What You Need, Quickly

Over 2 million registered users